Products

Maverix Cleaner 505 is a strong water-based cleaner that strips wax-based release coatings from composite or metal molds. This is a good cleaner for removing the yellowish-brown build-up from composite tooling that occurs with repeated use. Cleaner 505 also cleans light films of styrene buildup. It is a concentrated, heavy-duty, water-based cleaner that dissolves and removes the build-up that occurs over time from the interaction of mold release and rubber curing during many hours of repeated cycles. It will strip elastomer residues and particles from the mold to yield a clean metal surface for sustained production.

Maverix Cleaner 202 strips polymer-based, semi-permanent release coatings from composite or metal molds. It is a concentrated heavy-duty degreaser used to remove mold release coatings and pigment build-up from rotational molds. It is also used for general mold and part cleaning.

Maverix Cleaner 303 is a strong solvent-based cleaner that removes wax-based release coatings from composite or metal molds. Simply wipe 303 onto the mold surface and allow a short contact time for the chemistry to break down the residues and wipe clean. 303 will not harm mold surfaces, even those with class-A finishes.

Maverix Mold Cleaner – G is a gelled product that clings to vertical surfaces, stays in place, and does not run down the tooling surface. It is a non-flammable cleaner that dissolves, encapsulates, and lifts all thermoset resins, epoxies, phenolics, urethanes, and thermoplastics from metal molds. The gel strips residue build-up from the tooling surface without attacking the metal.

Maverix Cleaner 8700 is a heavy-duty general-purpose cleaner and degreaser used to clean equipment, presses, hydraulic fluid, and parts. 8700 is concentrated so it can be diluted with water to meet the needs of any specific application.

Maverix Mold Cleaner – L is the liquid version, which is also non-flammable and dissolves, encapsulates, and lifts all thermoset resins, epoxies, phenolics, urethanes, and thermoplastics from metal molds. The liquid form allows Cleaner – L to be used in dip tanks and parts cleaning operations.

Mavcoat® 524 Mold Cleaner is a special V.O.C. Free cleaner that contains no chlorinated solvents, CFCs, or ozone-depleting chemicals. The nozzle delivers powerful flushing steam to remove contaminants from mold surfaces. No wiping is necessary because the product evaporates completely while flushing away dirt, grease, and protection films such as Mavcoat® Mold Saver.

Mavcoat® CRW releases hardened concrete from all forms and formliners that yields clean, easy stripping without bugholes and stains. CRW is a concentrated product used in applications that require a stronger release agent in hard to demold situations. CRW meets California, OTC, and all other Federal VOC regulations. Mavcoat CRW will not separate, so there is no need to mix before use.

Mavcoat® 902M is the water-based version of Mavcoat® T-100. T-100 is solvent-based that uses non-silicone polymers to allow finished parts to be painted, printed, plated, or post decorated in any way.

Mavcoat® HR-W27 is water-based chemistry that releases all flexible polyurethane foam systems from molds made of steel, aluminum, epoxy, fiberglass, or urethane. HR-W27 is ideal for high resiliency seating foam or visco-elastic foam used in pillow or bedding applications.

Mavcoat® EP-111 is considered the workhorse in the industry. It is a semi-permanent, water-based, non-silicone coating that yields a matte finish with excellent cosmetics. The surface is free of porosity and pinholes. There is little to no transfer making for superior adhesion of paint, print, or decals. It is good for high volume production where release is applied to hot molds and yields multiple releases with a single application.

Mavcoat® 1000 coats and impregnates the nylon tape that is used to wrap mandrel-built rubber hoses. It prevents the tape from sticking to the rubber hose, making the re-usable nylon tape easy to remove. Tape life is prolonged, saving the operation money. Mavcoat® 1000 is a concentrated polymer solution that is diluted with water. It is also non-silicone so there is no contamination of the finished hose.

Mavcoat® TM-10 is a water-based semi-permanent release that is an alternative for Teflon coating your molds. The Mavcoat® TM-10 will produce a semi-gloss finish on your parts without any white haze. This will eliminate the need to flame treat most parts. The TM-10 will release all densities of linear and crosslink polyethylene resins as well as polycarbonate.

Mavcoat® PU-54 is a non-silicone water-based release coating specially formulated for release of rigid and flexible polyurethane foams and cast elastomers.

Mavcoat® MD-W54 is a semi-permanent water-based release agent for the most difficult compounds including AFLAS and other fluoroelastomers in complex molds.

Mavcoat® TPC-1 is a versatile coating designed to release all injection molded thermoplastic resins. It produces a very low coefficient of static friction so parts release easily. It resists film buildup, eliminates knit lines, and yields multiple releases with a single application. TPC-1 is food grade and meets FDA regulation 21 CFR181.28 as a release agent.

Mavcoat® EM is a ready-to-use, water-based system for high-volume production where application to hot molds is made frequently because a semi-permanent coating is not wanted or needed. Mavcoat® EM produces a glossy surface finish on all thermoset composite systems.

Mavcoat® GSMR is a concentrated, water-based coating used for mandrel-built parts that ease extraction of parts from mandrel because high-slip lubricity polymers reduce friction at the mold surface. Mavcoat® GSMR is concentrated so it can be shipped overseas and diluted with water at the manufacturing site. It yields superior release of all thermoset composite systems.

Mavcoat® HVP-E is odorless, solvent-based chemistry that releases all self-skinning urethane foam systems from molds made of steel, aluminum, epoxy, fiberglass, or urethane. The developed skin is uniform, demolds easily and with excellent cosmetics.

Mavcoat® STM is used to prevent uncured rubber from sticking to itself when rubber is stacked or coiled. Mavcoat® STM replaces messy talc and stearate-based dispersion. It is non-silicone, water-based, and clear. It does not contaminate the rubber or cause defects during molding operations.

Mavcoat® MBH is a specialized technology for making Mandrel-Built Hose on straight mandrels. It can be used as-is or diluted with water. Mavcoat® MBH will release all organic rubber elastomers. The technology seals, releases and lubricates the mandrel, which is then tightly wrapped with rubber and cured. The coating produces a very low coefficient of friction, so extraction is easy, and the finished hose slides from the mandrel with little effort.

Mavcoat® CFR-5 is the water-based version of Mavcoat® DHSR. It is a water-based coating that will prevent any rigid polyurethane foam from sticking to your parts' surface. During the foam filling process excess rigid foam will expand out vent holes attaching itself to the exterior of the part. Apply Mavcoat® CFR-5 anywhere rigid foam may come into contact to prevent the foam from sticking. Cured rigid foam can be easily removed without damaging or staining your part. The Mavcoat® CFR-5 will not discolor your parts' surface and it can be easily removed with soap and water.

Mavcoat® KCP contains unique additives for high slip and is used for difficult-to-release parts in the most demanding applications. Mavcoat® KCP is fast evaporating, solvent-based, and semi-permanent capable of releasing all thermoset composites. It is a quick-cure, fast evaporating, semi-permanent mold release coating for the release of reinforced polyester and vinyl-ester resins. Upon evaporation and cure, parts demold with a high gloss finish.

Mavcoat® Roto is a semi-permanent release that has the unique ability to release all densities of linear and crosslink polyethylene resins. We guarantee no pock-marking (coining) on crosslink parts when using Roto. And most importantly, Mavcoat® Roto maintains product dimensions without warping the part no matter how much is applied.

Mavcoat® BR is a water-based emulsion used to release rubber mats and all other parts made from recycled crumb rubber using urethane binder systems. Emulsion concentrate is usually diluted with water at varying levels to achieve the release needed for a given binder system. It prevents binder from building up on mold surface and keeps tooling clean to yield longer production runs between cleaning cycles.

Mavcoat® T-100 is solvent-based and uses non-silicone polymers that allow finished parts to be painted, printed, plated, or post decorated in any way. Mavcoat® T-100 provides the release of cast elastomers from all types of tooling that allows finished parts to be painted or post-decorated. Mavcoat® T-100 provides the release of integral skin foams from all tooling such as metalized epoxy, aluminum, or fiberglass.

Mavcoat® ND seals porosity of metal tools and accepts the mold release coating.

Mavcoat® FR-2 will make it easier to remove any build-up on your flanges. Only a thin film of the Mavcoat® FR-2 is needed to prevent material from sticking in the flanges. Keeping the flanges clean and free of build-up will eliminate air bubbles from forming along the parting line.

Mavcoat® MMR is the ready-to-use version of Mavcoat® GSMR so it does not require dilution. Mavcoat® MMR is a water-based coating used in high-volume production environments. Since it contains high-slip lubricity polymers, MMR yields superior release for parts built on mandrels or in compression and vacuum bagging operations. It is semi-permanent and will yield multiple parts with a single application or can be applied before every cycle in difficult demolding situations. It produces a glossy surface finish and releases all thermosets.

Mavcoat® NB is the “workhorse” and one of the best-selling odorless solvent-based products. It is designed for hand casting or high-volume automated production lines. It can be wiped on or spray applied with an airbrush. It is good for releasing all Shore A and some Shore D polyurethanes.

Mavcoat® EP-524 is a water-based, non-silicone, semi-permanent mold release coating that yields excellent cosmetic finish. It utilizes our proprietary ceramic-based technology which offers high thermal stability and releases polyester, epoxy, vinyl ester and other thermoset resins.

Mavcoat® CDNA is a specialized release coating for molded parts that must be free of any residue because the finished parts will be painted or bonded to after molding.

Mavcoat® RT-44 anti-static coating can be added to your dry powder or applied directly to the mold surface. This will improve granite appearance and eliminate color swirling that can occur with some dry blended materials.

Mavcoat® MD-4 is a water-based, semi-permanent release coating for all organic rubber elastomers. It contains a novel binder system that adheres strongly to the mold surface and a unique lubricity additive that allows for good rubber flow throughout the mold. Mavcoat® MD-4 is a non-silicone ceramic-based technology and can be used to make food grade products because it meets 21 CFR 181.28.

Mavcoat® AD seals the porosity of composite tools made from polyester, vinyl-ester, epoxy, and all other resin surfaces and accepts the mold release coating. AD helps to improve the surface quality of finished parts even for class A finished molds.

Mavcoat® FGR-4 is a quick-cure, fast evaporating, semi-permanent mold release coating for the release of reinforced polyester and vinyl-ester resins. FGR-4 is a stronger, polymer-based release that works better for non-gel coated parts and can be wiped or sprayed onto the mold surface.