Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Recommended Preparation
- Clean the substrate with Isopropyl Alcohol, MG #824, so the surface is free of oils, dust, and other residues.
- Features & Benefits
- Xylene and toluene free
- Fluoresces under UV-A light
Applications & Uses
- Application Method
Properties
- Typical Properties
- Cured Properties
- Uncured Properties
- Cure Instructions
Allow to dry at room temperature for 24 hours, or after letting sit for 10 minutes, cure the coating in an oven at one of these time/temperature options:
Temperature 65 °C 80 °C 100 °C 120 °C Time 30 min 20 min 10 min 5 min
| Value | Units | Test Method / Conditions | |
| Minimum Recoat Time | 3 | minute | — |
| Recommended Film Thickness | 25-75 | μm | — |
| Theoretical Coverage @ 25 μm | 94020 | cm2/L | — |
| Dry Time To Handle (1 coat) | 10 | minute | — |
| Dry Time To Handle (2 coats) | 20 | minute | — |
| Value | Units | Test Method / Conditions | |
| Resistivity | 4.6 x 10¹⁴ | Ω·cm | — |
| CTE Prior Tg | 72 | ppm/°C | — |
| Dielectric Strength | 1000 | V/mil | — |
| Dielectric Withstand Voltage | min. 1 500 | V/mil | — |
| Service Temperature Range | -65 to 125 | °C | — |
| Insulation Resistance | 1 x 10¹³ | Ω | — |
| Moisture Insulation Resistance | 1 x 10¹² | Ω | — |
| Dielectric Constant (at 1 MHz) | 2.85 | — | — |
| Dissipation Factor (at 1 MHz) | 0.004 | — | — |
| Glass Transition Temperature (Tg) | 27 | °C | — |
| Value | Units | Test Method / Conditions | |
| Solid Content | 30 | % | — |
| Calculated VOC | 654 | g/L | — |
| Viscosity (at 25˚C) | 115 | cP | — |
| Density | 0.92 | g/mL | — |
Regulatory & Compliance
- Chemical Inventories
- Quality Standards
- Certified
- UL 94 V-0 (File# E203094)
- IPC-CC-830B
Technical Details & Test Data
- Spray
- Shake the can vigorously.
- Spray a test pattern to ensure good flow quality.
- Tilt the board at 45° and spray a thin, even coat from a distance of 20–25 cm (8–10 in). Use spray-andrelease strokes with an even motion to avoid paint buildup in one spot. Start and end each stroke off the surface.
- Wait 3 min before applying another coat, to avoid trapping solvent.
- Rotate the board 90° and spray again to ensure good coverage.
- Apply additional coats until desired thickness is achieved (go to step 3).
- Let dry 3 min at room temperature before applying heat cure.
- After use, clear the nozzle by inverting the can and briefly spraying until clear propellant comes out.
Packaging & Availability
- Available Packaging
Cat. No. Packaging Net Vol. Net Wt. 419D-340G Aerosol 410 mL 340 g
Storage & Handling
- Shelf Life
- 5 years
- Storage and Handling
- Store between -5 and 40 ˚C in a in a dry area, away from sunlight (see SDS).