Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
- Product Highlights
- High gloss and deep piano black available.
- Other premium colors such as white, red, orange, blue, etc. are possible
- Excellent mechanical properties
- Superb weather-resistance and UV-resistance
- Ductility with good impact resistance
- Good scratch resistance
- Bio-based material
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Application Information
Drying Condition:
- Pre-dry is necessary.
- Please dry until moisture content can be less than 500 ppm (less than 0.05%) prior to using. It can be carried out as follows:
Dryer Temperature Hours Hot-air Dryer 95°C More than 7 hours
Vacuum Dryer 90°C More than 7 hours
- The maximum recommended temperature must not be exceeded as this may cause aggregation or other defects.
Start-up:
- Purge machine completely with DURABIO or other acceptable purging material.
- DURABIO is not compatible with conventional polycarbonate, purge machine completely if conventional polycarbonate resin was in the previously in the machine.
Properties
- Mechanical Properties
- Typical Properties
- Thermal Properties
- Processing Information (Injection Molding)
| Value | Units | Test Method / Conditions | |
| Tensile Modulus | 2200.0 | MPa | ISO527 |
| Tensile Strength | 63.0 | MPa | ISO527 |
| Elongation (at break) | 120.0 | % | ISO527 |
| Flexural Modulus | 2200.0 | MPa | ISO178 |
| Flexural Strength | 90.0 | MPa | ISO178 |
| Charpy Impact Strength (Notched, at 23°C) | 60.0 | kJ/m² | ISO179-1/1eA |
| Charpy Impact Strength (Unnotched, at 23°C) | No Break | kJ/m² | ISO179-1/1eU |
| Value | Units | Test Method / Conditions | |
| Density | 1.3 | g/cm³ | ISO1183 |
| Melt Volume Flow Rate (at 230°C, 2.16kg) | 8.0 | cm³/10min | ISO1133 |
| Melt Mass Flow Rate (at 230°C, 2.16kg) | 9.0 | g/10min | ISO1133 |
| Value | Units | Test Method / Conditions | |
| Heat Deflection Temperature (at 1.80MPa) | 88.0 | °C | ISO75-1, ISO75-2 |
| Heat Deflection Temperature (at 0.45MPa) | 100.0 | °C | ISO75-1, ISO75-2 |
| Value | Units | Test Method / Conditions | |
| Hopper Area Temperature | approx. 50 | °C | — |
| Barrel Temperature (Rear Hopper side) | 220 - 240 | °C | — |
| Barrel Temperature (Center) | 220 - 250 | °C | — |
| Barrel Temperature (Front Nozzle side) | 220 - 250 | °C | — |
| Nozzle Temperature | 220 - 250 | °C | — |
| Mold Temperature | 60 - 100 | °C | — |
| Screw Speed (Refill) | 30 - 60 | rpm | — |
| Back Pressure (Refill) | 10 - 25 | MPa | — |
| Decompression (Refill) | 1 - 4 | mm | — |
| Injection Rate (Injection) | 10 - 60 | cm³/sec | — |
| Holding Pressure (Injection) | 40 - 100 | MPa | — |
| Holding Time (Injection) | 3 - 10 | sec | — |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Packaging Type
- Packaging Information
DURABIO is typically packed in 25kg paper bags with polyethylene inner liner.
Storage & Handling
- Storage Information
- Do not store outdoors. Keep dry at ambient temperature.
- Avoid humid environment, heat and direct sunlight.
- The material needs to be pre-dried before processing.