Products

Viscoat #190 (EOEOEA, EEEA, CBA) is famous polar acrylate but our EEEA called V#190 has different properties compared with other company’s products. Our V#190 is highly distillated, so that it has very low viscosity and color, and no difunctional impurities derived from polyethylene glycol. Our competitors’ product have relatively higher viscosity, higher color, and cannot be a comonomer for acrylic copolymer. Recently, very low volatiles during UV radiation properties are reported [1]. So if you use our products, you can cut down on the frequency of UV lamp maintenance and the work environment will improve because the volatiles will be reduced. V#190 is suitable for adhesives because it has low Tg and high elongation properties along with a polar nature (enough polarity to aid in adhesion, but still an effective diluent for non-polar resins).

Viscoat #155 (CHA) has a simple structure. Cycloalkyl structure induces weatherability with low viscosity, good compatibility and lower shrinkage. As compared with isobornyl acrylate, its viscosity is very low. CHA has relatively higher Tg than other acrylic monomers. Sometimes CHA is used for photoresist because it is easy to hydrolysis because cyclohexanol is secondary alcohol.

MEDOL-10 has a novel unique structure. It was developed for replacement of THFA, tetrahydrofurfuryl acrylate. MEDOL-10 only has exclamation pictogram on REACH. Its viscosity is low enough for many applications like UV inkjet ink. Some of paper said high polarity pendant group induces high curing speed [1]. Dioxolane structure induces high solvency as same as THFA because both THF and dioxolane are good solvent.

Viscoat #196, TMCHA is a good UV diluent with high Tg and low viscosity. It is also highly distillated, so that it has higher purity than the competitors’ product. It has lower smell among cycloaliphatic acrylate.

HPA is one of the reasonable hydroxyalkyl acrylates like HEA. It is second choice for crosslinking site of acrylic resin of paintings, adhesives, inks etc. HPA is also useful to control Hydrophilicity and adhesiveness to polar substrate because of it polar hydroxyalkyl moiety. HPA has low di-ester because the reactivity of secondary hydroxyl group is lower than primary hydroxyl group.

HEA is the most reasonable hydroxyalkyl acrylate. It is first choice for crosslinking site of acrylic resin of paintings, adhesives, inks etc. HEA is also useful to control Hydrophilicity and adhesion to polar substrate because of it polar hydroxyalkyl moiety. Our HEA has lower Di-ester impurities than any other companies. It is useful for many industries who want to control cross-linking side reaction. Be careful handling HEA because it has toxicity, corrosivity, mutagenicity because of its fundamental reactivity. We also have lower toxic hydroxyalkyl acrylate, 4-HBA (4-hydroxybutyl acrylate).

Viscoat #150 (THFA) is widely used for UV diluent applications because it is almost colorless and has a high solvency derived from THF group. Because of this high solvency, THFA has strong adhesion properties with several plastics especially PC. You can cut down on the frequency of UV lamp maintenance and the working environment will improve because of limited volatiles. Recently the dynamics of poly(THFA) hydrogels have been well studied. Inter molecular interaction of these gels could be formed by hydrogen bonding or entanglement of bulky THF groups Blood Compatibility of poly(THFA) is also studied. Its pendant group is bio-based. It helps carbon-neutral business. The differences between our product and competitor's product are lower color, lower viscosity and better quality consistency. These differences are derived from our unique distillation process.

4-HBA is used for acrylic resins, adhesives, UV diluent. It is water miscible. Its OH group of co-polymer is higher reactivity than the other hydroxyalkyl monomers like HEMA and HEA because of the longer alkyl chain between OH group and polymer main chain. The 2K urethane painting with 4-HBA has higher scratch resistance and stronger mechanical properties because it can form higher crosslinking density due to highly reactive OH group. 4-HBA is also used for UV diluent application because the lower toxicity than the other hydroxyalkyl acrylates, like HEA and HPA which are classified as CMR substances in most of countries.

BAC-45 is UV curable polyolefin. It is one of the highest elastic and most hydrophobic monomer among the acrylate oligomers due to polybutadiene structure. It does not have urethane bonding compared with the competitors' products.

V-3F is registered in many countries.It has fluorine properties like water / oil repellency, low surface tension, low RI, and low gas transparency. This Product is not applicable PFOA / PFOS problem due to shorter alkyl chain so far. Please be aware these monomers are easy to volatile because F atoms induce weak intermolecular interaction. Recently these materials are studied specialty application like living radical polymerization, oligomer for nano-imprint photolithography, and synthetic opal.

Lauryl acrylate is made from renewal source so that it helps your carbon-neutral business. Our LA is a single component C12, however, our competitors’ lauryl (meth)acrylate include not only C12 lauryl, but also C14 myristyl because of its alcohol nature. Long alkyl chain moiety induces low viscosity, surface tension and polarity. LA is used for UV inkjet inks because of its soft and flexibilizing properties [1]. And it is also used for adhesives and finish coatings because of its slippage. Recently high purity LA is investigated for polymer brush made by ATRP (Atom Transfer Radical Polymerization) with Stearyl acrylate [2], or fabrication of ultrahydrophobilc on silicon wafer 3]. They are called as Side Chain Crystallization polymer, and have not only Tg, but also melting point (Tm) even though usual acrylic polymers do not have Tm.

Our IBXA is the world highest purity of isobornyl acrylate with great quality consistency. It is commonly used for painting resins, adhesives and UV diluents. Viscosity of an Acrylic Polyol (which is raw material of urethane/melamine 2K coatings) has a very high viscosity because of its hydrogen bonding. High viscosity induces low working efficiency, low solid contents and of course high VOC. Frank et al. [1] reported that polymerization hydroxyl acrylics with bulky acrylic monomers inhibit this hydrogen bond, resulting in high solids and low viscosity Acrylic Polyols. IBXA is one of the most famous bulky acrylics. IBXA have the highest Tg in mono functional acrylics (except methacrylate), so it is useful in the application that cannot use methacrylates like the adhesive industry or for UV diluents. Recently, poly(IBXA) is employed in microfluidic devices because of desirable properties, such as inertness, transparency, and resolution [2]

Osaka Organic Chemical Industry LTD STA has a very long alkyl chain moiety. Its homopolymers are called Side Chain Crystallization polymers and have not only a Tg but also a melting point (Tm), even though usual acrylic polymers do not have a Tm. The product properties are achieved by its long alkyl chain, comb-like amorphous/semi-crystal phase transition. STA is highly purified, so it can be used for emulsion polymerization due to the absence of alcohol.

OXE-30 have different two polymerization moieties, radical and cationic polymerization moieties. OXE-30 is a methacrylate analog. We can make cationic polymerizerable acrylic resin. It is well known that oxetane group has lower reactivity than epoxy group, however, we can use slight amount of epoxy group to accelerate of polymerization of oxetane group because its slowest step is ring opening reaction. We cannot offer glycidyl acrylate due to too much toxicity, so that OXE-10 is a one of the simplest structure for UV/cationic dual cure system.

V-8FM is registered in many countries.It has fluorine properties like water / oil repellency, low surface tension, low RI, and low gas transparency. This Product is not applicable PFOA / PFOS problem due to shorter alkyl chain so far. Please be aware these monomers are easy to volatile because F atoms induce weak intermolecular interaction. Recently these materials are studied specialty application like living radical polymerization, oligomer for nano-imprint photolithography, and synthetic opal.

GMEC is methacrylate monomer with propylene carbonate (PC) moiety. The reactivity of this monomer has been widely studied [1, 2, 3] but it seems that it has not been commercially available. Thermosetting coatings based on the cyclic carbonate-amine reaction are attractive because polyurethane coatings can be made neither isocyanate nor tin catalyst under moderate conditions like 80˚C [1, 2, next page]. That means we can make acryl urethane paint without residual isocyanate and harmful tin. In addition, PC is well used as battery electrolyte solution of ultracapacitor because of its high polarizability, electrolyte solubility, and boiling point. Therefore, the polymer having cyclic carbonate group solves great amount of electrolyte, then the solution (or gel) has high ionic conductivity [3].

2-MTA is high polarity, low viscosity acrylate monomer. It is the first choice if you need high polarity monomer. It brings soft, flexible and elongate properties to your materials because of methoxyethyl moiety. It is used for acryl rubber to add cold resistance derived from low Tg.

V#802 has unique structure. Some pentaerthritols are connected each other and then acrylated, so it has high functionality, 7-10. The properties of V#802 are extended DPHA. Although Double bond equivalent is PETA < DPHA < #802, it has very hard property and high sensitivity. It has high molecular weight and viscosity, but the compatibility is not so bad. V#802 is solved into IPA, Toluene, Ethyl acetate, MEK and so on. .

RILY is specialty methacrylate, which has phenolic hydroxyl group. It has good rigidity, mechanical property and solvent resistance due to aromatic ring. It can be solved into several solvents as described below. It is well used in electronic material industry.

Viscoat #216 (BACA) is a urethane mono-functional acrylate. It has higher purity than our competitors’ product. Due to high purity, it has lower viscosity as UV diluent, and it can form linear copolymer as usual distillated mono-functional acrylate. Users can make better shelf life product due to absence of multi-functional impurities. You can design a polymer that has very high polarity pendant group.

V-4F is registered in many countries.It has fluorine properties like water / oil repellency, low surface tension, low RI, and low gas transparency. This Product is not applicable PFOA / PFOS problem due to shorter alkyl chain so far. Please be aware these monomers are easy to volatile because F atoms induce weak intermolecular interaction. Recently these materials are studied specialty application like living radical polymerization, oligomer for nano-imprint photolithography, and synthetic opal.

ISTA from Osaka Organic Chemical is highly purified by distillation. It has highly branched bulky pendant group. Because of this structure, it has low polarity, low permittivity, high Tg, low surface tension, high dispersive power and high anti-hydrolysis properties. Main application is adhesives to control Tg, surface tension, permittivity and slippage properties. ISTA is also highly distilled even though it has high molecular weight. It has the lowest acrylic equivalent monomer in the distilled monomer We can handle ISTA easily because it is liquid product compared with linier stearyl acrylate, a solid acrylate.

OXE-10 have different two polymerization moieties, radical and cationic polymerization moieties. OXE-10 is an acrylate analog. We can make cationic polymerizerable acrylic resin. It is well known that oxetane group has lower reactivity than epoxy group, however, we can use slight amount of epoxy group to accelerate of polymerization of oxetane group because its slowest step is ring opening reaction. We cannot offer glycidyl acrylate due to too much toxicity, so that OXE-10 is a one of the simplest structure for UV/cationic dual cure system.

MPE550A are poly(EO) mono-ether mono-acrylates. Basically this structures tend to have diester impurities because its raw material, methoxy poly(EO) tends to have polyethyleneglycol impurities, however, we are controlling diesters’ content for resin/adhesive manufactures. You can put this very high polar moiety into your copolymers easily. MPE400A has shorter poly(EO) chain than MPE550A.

V-8F is registered in many countries.It has fluorine properties like water / oil repellency, low surface tension, low RI, and low gas transparency. This Product is not applicable PFOA / PFOS problem due to shorter alkyl chain so far. Please be aware these monomers are easy to volatile because F atoms induce weak intermolecular interaction. Recently these materials are studied specialty application like living radical polymerization, oligomer for nano-imprint photolithography, and synthetic opal.

Branched C8 structure like 2-ethylhexyl acrylate and iso-octyl acrylate are famous, but NOAA has linear C8 structure. C8 moiety of NOAA is derived from renewal resources nevertheless the others are derived from petrol. NOAA has very soft property due to its linear structure. It is well used for soft material like adhesives. NOAA can be a co-monomer with the other various monomers because it is highly distillated.

V#192HP is a highly purified ester of phenoxyethanol and acrylic acid. V#192HP is used for UV diluent inks for the same reason. Generally, aromatic moiety gives tough films with excellent solvent resistance but the adhesion may not be as good as the aliphatic cyclic monomers, but adhesion property of V#192HP is relatively better in the aromatic monofunctional acrylate group [1]. V#192HP is also used for adhesives because of good compatibility and adhesion properties. Sometimes its raw material, phenoxyethanol is considered as Endocrine Disruptors, however, our highly distilled products has really limited amount of it.

V-13F is registered in many countries.It has fluorine properties like water / oil repellency, low surface tension, low RI, and low gas transparency. This Product is not applicable PFOA / PFOS problem due to shorter alkyl chain so far. Please be aware these monomers are easy to volatile because F atoms induce weak intermolecular interaction. Recently these materials are studied specialty application like living radical polymerization, oligomer for nano-imprint photolithography, and synthetic opal.

BZA is the simplest mono functional acrylate that has aromatic ring. As the result BZA is one of the highest refractive index monomer among mono functional distilled high purity acrylate and that has high heat resistance. Polymer of BZA has good dispersant property with some of pigment due aromatic ring. Osaka Organic Chemical is the Lead Registrant of BZA in REACh. BZA is also known as low viscosity monomer. Our product is highly distilled. We can make homo- or co-polymer of the monomer because of high purity. Quality consistency is also very good.

Viscoat#200 (CTFA) is highly purified. Generally, our competitors’ CTFA includes TMPTA and its oligomeric multi-functional impurities because of synthetic limitation. However, our product highly purified so that it does not have TMPTA and multifunctional impurities. The viscosity is lower than the others due to absent of the oligomeric impurities. CTFA is one of the lowest odor monomer among the UV diluent.

MPE400A are poly(EO) mono-ether mono-acrylates. Basically this structures tend to have diester impurities because its raw material, methoxy poly(EO) tends to have polyethyleneglycol impurities, however, we are controlling diesters’ content for resin/adhesive manufactures. You can put this very high polar moiety into your copolymers easily. MPE400A has shorter poly(EO) chain than MPE550A.