Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Applications
- Application Method
- Cure Method
- Processing
- The processing of two component products from side by side cartridges is very simple
- The cartridge is inserted into a suitable dispensing gun. The closing cap of the cartridge is then removed and replaced by an according static mixing nozzle
- By activating the trigger of the dispensing gun, the two components are pressed out and automatically mixed in the static mixer
- In order to prevent mixing errors, dispose the first half of the content in the mixing nozzel prior to application
- Processing should be carried out rapidly after mixing the components as an indication, the pot life can be used
- When the pot life is exceeded, the mixing tube should be replaced with a new one
- Close the cartridge with the cap after use
- Surfaces should be clean, thus free of dirt, grease, oil, dust or process chemicals
- Please take care of respective minimum curing temperature and time
Properties
- Physical Form
- Typical Properties
- Cured Properties
- Uncured Properties
- Note
*Curing temperatures refer to the temperature in the respective bond line. When choosing the respective curing conditions, the time needed to heat the substrate has to be considered. Depending on the type of heat source (convection oven, hot stamp, heating plate) the heat input may vary.
| Value | Units | Test Method / Conditions | |
| Curing Time (23°C) | 24.0 | Hours | — |
| Curing Time (80°C) | 60.0 | Minutes | — |
| Curing Temperature | min. 15 | °C | — |
| Value | Units | Test Method / Conditions | |
| Coefficient of Thermal Expansion (<Tg) | 28.0 | ppm | ISO 11359-2 |
| Coefficient of Thermal Expansion (>Tg) | 91.0 | ppm | ISO 11359-2 |
| Degradation Temperature | 300.0 | °C | TM 302 |
| Elongation at Break | 3.5 | % | TM 605 |
| Glass Transition Temperature (Tg) | 65.0 | °C | TM 501 |
| Hardness | 85.0 | Shore D | DIN EN ISO 868 |
| Lap Shear Strength (Al/Al) | 14.0 | N/mm² | TM 604 |
| Maximum Service Temperature (Continuous) | -55 to 150 | °C | TM 302 |
| Maximum Service Temperature (Short-Term) | -55 to 240 | °C | TM 302 |
| Tensile Strength | 27.0 | N/mm² | TM 605 |
| Thermal Conductivity | 2.1 - 2.3 | W/m.K | TM 502 |
| Young's Modulus | 5000.0 | N/mm² | TM 605 |
| Value | Units | Test Method / Conditions | |
| Chemical Basis | Epoxy | — | — |
| Consistency | Creamy paste | — | TM 101 |
| Density (A-Part) | 1.9 | g/cm³ | TM 201.2 |
| Density (B-Part) | 1.7 | g/cm³ | TM 201.2 |
| Density (Mix) | 1.8 | g/cm³ | TM 201.2 |
| Mixing Ratio (Volume) | 7260 | — | — |
| Mixing Ratio (Weight) | 1900-01-03T04:47:00+00:00 | — | — |
| Number of Components | 2.0 | — | — |
| Type of Filler | Boron nitride | — | — |
| Viscosity Mix (84s⁻¹, 23°C) | 180000.0 | mPa.s | TM 202.1 |
Packaging & Availability
- Standard Pack Sizes
- 50 mL 2K cartridges
- Customized Packaging
Storage & Handling
- Pot Life (23°C)
- 30 Minutes
- Shelf Life
- 12 months at 23°C