LNP™ LUBRICOMP™ Compound LL004C

Identification & Functionality

Additives Included

Lubricant (PTFE)

Chemical Family

Polyether Ether Ketone (PEEK)

Fillers Included

PTFE

Polymer Name

Polyetheretherketone (PEEK)

Plastics & Elastomers Functions

Resin

Technologies

Plastics

Product Families

Plastics — Engineering & Specialty Polymers

High Performance Thermoplastics

Features & Benefits

Materials Features

Electrically Conductive,

Friction Resistant,

High Temperature Resistance,

Low Liquid Particle Count,

Low Outgassing,

Unreinforced,

Very Good Heat Resistance,

Wear Resistant

Applications & Uses

Markets

Consumer Goods,

Electrical & Electronics,

Industrial

Applications

Consumer Goods — Appliances & Electronics

Industrial — Chemical & Industrial Manufacturing

Equipment & Parts

Electrical & Electronics — Devices & Assemblies

Consumer Electronics,

Displays,

Industrial Automation

Electrical & Electronics — Parts & Components

Connectors,

Semiconductor Manufacturing,

Switches & Relays

Plastics & Elastomers End Uses

Cell Phones,

Computer Components,

Displays,

Electrical Components,

Electrical/Electronic Applications,

Industrial Applications,

Semiconductor Applications,

Tablets,

Trays

Plastics & Elastomers Processing Methods

Injection Molding

Properties

Mechanical Properties

	Value	Units	Test Method / Conditions
Tensile Stress (Yield) ¹¹	74	MPa	ASTM D638
Tensile Stress (Yield) ¹¹	73	MPa	ISO 527
Tensile Stress (Break) ¹¹	69	MPa	ASTM D638
Tensile Stress (Break) ¹¹	69	MPa	ISO 527
Tensile Strain (Yield) ¹¹	5.8	%	ASTM D638
Tensile Strain (Yield) ¹¹	5	%	ISO 527
Tensile Strain (Break) ¹¹	11.8	%	ISO 527
Tensile Strain (Break) ¹¹	23.3	%	ASTM D638
Tensile Modulus (at 50 mm/min) ¹¹	2890	MPa	ASTM D638
Flexural Stress ¹¹	118	MPa	ISO 178
Flexural Stress ¹¹	117	MPa	ASTM D790
Flexural Modulus ¹¹	2960	MPa	ASTM D790
Flexural Modulus ¹¹	3320	MPa	ISO 178
Tensile Modulus (at 1 mm/min) ¹¹	3060	MPa	ISO 527

Physical Properties

	Value	Units	Test Method / Conditions
Density ¹¹	1.37	g/cm³	ISO 1183
Density ¹¹	1.37	g/cm³	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.06	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	1.3	%	ISO 294
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	1.3	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	1.9	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	1.85	%	ISO 294
Wear Factor Washer ¹¹	128	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.52	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.43	—	ASTM D3702 Modified: Manual

Impact Properties

	Value	Units	Test Method / Conditions
Izod Impact (Unnotched, at 23°C) ¹¹	1548	J/m	ASTM D4812
Izod Impact (Notched, at 23°C) ¹¹	96	J/m	ASTM D256
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹	3	J	ASTM D3763
Multi-Axial Impact ¹¹	1	J	ISO 6603
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹	91	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹	8	kJ/m²	ISO 180/1A

Injection Molding

	Value	Units	Test Method / Conditions
Drying Temperature ⁷	150	°C	—
Drying Time ⁷	4 - 6	Hrs	—
Front - Zone 3 Temperature ⁷	380 - 400	°C	—
Middle - Zone 2 Temperature ⁷	380 - 400	°C	—
Rear - Zone 1 Temperature ⁷	370 - 380	°C	—
Mold Temperature ⁷	175 - 190	°C	—
Back Pressure ⁷	0.3 - 0.7	MPa	—
Screw Speed ⁷	60 - 100	rpm	—

Note

• ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
• ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
• ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

 

Packaging & Availability

Regional Availability

• Americas
• Asia
• Europe
• North America