LNP™ STAT-KON™ Compound EX07311P

Identification & Functionality

Additives Included

Heat Stabilizer,

Lubricant (PTFE)

Chemical Family

Polyetherimide (PEI),

Polyimides (PI)

Fillers Included

Carbon Fiber,

Glass Fiber,

PTFE

Polymer Name

Polyether Imide (PEI)

Plastics & Elastomers Functions

Resin

Technologies

Plastics

Product Families

Plastics — Engineering & Specialty Polymers

High Performance Thermoplastics

Features & Benefits

Materials Features

Dimensional Stability,

ESD Protection,

Electrically Conductive,

Friction Resistant,

Heat Stabilized,

High Stiffness,

High Strength,

High Temperature Resistance,

Light Weight,

Low Liquid Particle Count,

Low Outgassing,

Lubricated,

Very Good Heat Resistance,

Wear Resistant

Applications & Uses

Markets

Consumer Goods,

Electrical & Electronics,

Industrial

Applications

Consumer Goods — Appliances & Electronics

Industrial — Chemical & Industrial Manufacturing

Equipment & Parts

Electrical & Electronics — Devices & Assemblies

Consumer Electronics,

Displays,

Industrial Automation

Electrical & Electronics — Parts & Components

Connectors,

Semiconductor Manufacturing,

Switches & Relays

Plastics & Elastomers End Uses

Cell Phones,

Circuit Protection,

Computer Components,

Displays,

Electrical Components,

Electrical/Electronic Applications,

Industrial Applications,

Semiconductor Applications,

Tablets

Plastics & Elastomers Processing Methods

Injection Molding

Properties

Mechanical Properties

	Value	Units	Test Method / Conditions
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	175	MPa	ASTM D638
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	2.1	%	ASTM D638
Tensile Modulus (at 5 mm/min) ¹¹	15000	MPa	ASTM D638
Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹	200	MPa	ASTM D790
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	11500	MPa	ASTM D790
Tensile Stress (Break, 5 mm/min) ¹¹	174	MPa	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	1.9	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	15200	MPa	ISO 527
Flexural Stress (Yield, at 2 mm/min) ¹¹	203	MPa	ISO 178
Flexural Strain (Break, at 2 mm/min) ¹¹	1.7	%	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	13200	MPa	ISO 178

Physical Properties

	Value	Units	Test Method / Conditions
Density ¹¹	1.56	g/cm³	ASTM D792
Density ¹¹	1.56	g/cm³	ISO 1183
Mold Shrinkage (flow) ᵍ ¹¹	0.29	%	SABIC method
Mold Shrinkage (xflow) ᵍ ¹¹	0.36	%	SABIC method
Wear Factor Washer ¹¹	20	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.4	—	ASTM D3702 Modified: Manual
Melt Volume Rate (at 345°C, 10.0 kg) ¹¹	30	cm³/10 min	ISO 1133

Thermal Properties

	Value	Units	Test Method / Conditions
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	202	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000089	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000438	1/°C	ASTM E831
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹	204	°C	ISO 75/Af

Electrical Properties

	Value	Units	Test Method / Conditions
Volume Resistivity ᵈ ¹¹	100000 - 1000000	Ω.cm	ASTM D257
Surface Resistivity ᵈ ¹¹	100000 - 1000000	Ω	ASTM D257
Surface Resistivity (ROA) ¹¹	100000 - 1000000	Ω	IEC 60093

Impact Properties

	Value	Units	Test Method / Conditions
Izod Impact (Notched, at 23°C) ¹¹	56	J/m	ASTM D256
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹	6	kJ/m²	ISO 180/1A

Injection Molding

	Value	Units	Test Method / Conditions
Drying Temperature ⁷	150	°C	—
Drying Time ⁷	4 - 6	Hrs	—
Maximum Moisture Content ⁷	0.02	%	—
Melt Temperature ⁷	360 - 375	°C	—
Rear - Zone 1 Temperature ⁷	355 - 365	°C	—
Middle - Zone 2 Temperature ⁷	360 - 370	°C	—
Front - Zone 3 Temperature ⁷	365 - 375	°C	—
Nozzle Temperature ⁷	365 - 375	°C	—
Mold Temperature ⁷	140 - 180	°C	—
Back Pressure ⁷	0.3 - 0.7	MPa	—
Screw Speed (Circumferential speed) ⁷	0.2 - 0.3	m/s	—
Vent Depth ⁷	0.025 - 0.076	mm	—

Note

• ᵈ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding. Do NOT mix NORYL GTX* resin with other grades of NORYL* resins. Polystyrene and acrylic regrind are effective purging Materials. Use temperature range appropriate for particular purging resin. Regrind must also be dried. Maximum 25% regrind. Dry at recommended temperatures and times for optimum performance. Overdrying can cause loss of physical properties and/or create appearance defects. Do not exceed recommended basic drying time and temperature above or:\n4-8 hrs at 95°C (200°F), 10 hrs max\n6-12 hrs at 80°C (175°F), 16 hrs max\n8-16 hrs at 65°C (150°F), 24 hrs max\nAVOID air circulating tray ovens. Moisture levels in heated ambient air can exceed moisture level in the resin itself, causing moisture ABSORPTION not drying. Avoid melt temperature in excess of 300°C (575°F) and residence times over 6-8 minutes (may affect properties and/or appearance). Nozzle temperature controls assist in elimination of drool premature freeze-off. Shot sizes in excess of 50% barrel capacity can lead to difficulties in providing a consistent, homogenous plastic melt.
• ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
• ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
• ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

 

Packaging & Availability

Country Availability

Canada,

China (Mainland),

Mexico,

USA

Regional Availability

• Americas
• Asia
• Europe
• North America