LNP™ THERMOCOMP™ Compound JF004L

Identification & Functionality

Chemical Family

Polysulfones

Fillers Included

Glass Fiber

Polymer Name

Polyethersulfone (PES)

Plastics & Elastomers Functions

Resin

Technologies

Plastics

Product Families

Plastics — Engineering & Specialty Polymers

High Performance Thermoplastics

Features & Benefits

Labeling Claims

Food Contact Acceptable,

No Added PFAS

Materials Features

Cost Effective,

Food Contact Acceptable,

High Impact Resistance,

High Modulus,

High Stiffness,

High Temperature Resistance,

Low Extractables,

Low Leachable,

No Added PFAS,

Very Good Heat Resistance

Applications & Uses

Markets

Building & Construction,

Consumer Goods,

Electrical & Electronics,

Printing & Packaging

Applications

Consumer Goods — Appliances & Electronics

Building & Construction — Building Materials

Pipes & Plumbing

Electrical & Electronics — Devices & Assemblies

Consumer Electronics

Printing & Packaging — Packaging

Food & Beverage Packaging,

Industrial & Transport Packaging,

Non-Food Consumer Packaging

Plastics & Elastomers End Uses

Appliances,

Consumer Applications,

Food Packaging,

Home Appliances,

Hoses,

Pipes,

Water Management

Plastics & Elastomers Processing Methods

Injection Molding

Properties

Mechanical Properties

	Value	Units	Test Method / Conditions
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹	98	MPa	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	98	MPa	ASTM D638
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹	2.7	%	ASTM D638
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	2.9	%	ASTM D638
Tensile Modulus (at 50 mm/min) ¹¹	6360	MPa	ASTM D638
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹	152	MPa	ASTM D790
Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹	152	MPa	ASTM D790
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	6300	MPa	ASTM D790
Tensile Stress (Yield, 5 mm/min) ¹¹	94	MPa	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	93	MPa	ISO 527
Tensile Strain (Yield, 5 mm/min) ¹¹	2.1	%	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	2.1	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	6640	MPa	ISO 527
Flexural Stress ¹¹	149	MPa	ISO 178
Flexural Stress (Break, 2 mm/min) ¹¹	148	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	6300	MPa	ISO 178

Physical Properties

	Value	Units	Test Method / Conditions
Specific Gravity ¹¹	1.54	—	ASTM D792
Density ¹¹	1.53	g/cm³	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.37	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.3 - 0.6	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.5 - 0.7	%	ASTM D955
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.55	%	ISO 62

Thermal Properties

	Value	Units	Test Method / Conditions
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	216	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	211	°C	ASTM D648
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹	216	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹	210	°C	ISO 75/Af

Impact Properties

	Value	Units	Test Method / Conditions
Izod Impact (Unnotched, at 23°C) ¹¹	563	J/m	ASTM D4812
Izod Impact (Notched, at 23°C) ¹¹	50	J/m	ASTM D256
Multi-Axial Impact ¹¹	2	J	ISO 6603
Instrumented Dart Impact Total Energy (at 23°C) ¹¹	11	J	ASTM D3763
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹	32	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹	5	kJ/m²	ISO 180/1A

Injection Molding

	Value	Units	Test Method / Conditions
Drying Temperature ⁷	120 - 150	°C	—
Drying Time ⁷	4	Hrs	—
Maximum Moisture Content ⁷	0.05	%	—
Melt Temperature ⁷	355 - 370	°C	—
Front - Zone 3 Temperature ⁷	370 - 380	°C	—
Middle - Zone 2 Temperature ⁷	360 - 370	°C	—
Rear - Zone 1 Temperature ⁷	345 - 355	°C	—
Mold Temperature ⁷	140 - 150	°C	—
Back Pressure ⁷	0.3 - 0.7	MPa	—
Screw Speed ⁷	60 - 100	rpm	—

Note

• ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
• ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
• ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

 

Packaging & Availability

Country Availability

Canada,

China (Mainland),

Mexico,

USA

Regional Availability

• Americas
• Asia
• Europe
• North America