Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Break, Type I, 5 mm/min) ¹¹ 314 MPa ASTM D638 Tensile Strain (Break, Type I, 5 mm/min) ¹¹ 1.7 % ASTM D638 Tensile Modulus (at 5 mm/min) ¹¹ 31700 MPa ASTM D638 Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹ 477 MPa ASTM D790 Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ 27100 MPa ASTM D790 Tensile Stress (Break, 5 mm/min) ¹¹ 319 MPa ISO 527 Tensile Strain (Break, 5 mm/min) ¹¹ 1.5 % ISO 527 Tensile Modulus (at 1 mm/min) ¹¹ 35320 MPa ISO 527 Flexural Stress ¹¹ 457 MPa ISO 178 Flexural Modulus (at 2 mm/min) ¹¹ 27230 MPa ISO 178 Shear Modulus ¹¹ 4756 MPa ASTM D732 Shear Strength ¹¹ 119 MPa ASTM D732 - Physical Properties
Value Units Test Method / Conditions Specific Gravity ¹¹ 1.4 - ASTM D792 Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ 0.05 % ASTM D570 Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ 0.15 - 0.3 % ASTM D955 Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ 0.7 - 1.4 % ASTM D955 Poisson's Ratio ¹¹ 0.44 - ASTM E132 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 332 °C ASTM D648 Coefficient of Thermal Expansion (at -40°C to 150°C, flow) ¹¹ 0.000005 1/°C ASTM E831 Coefficient of Thermal Expansion (at -40°C to 150°C, xflow) ¹¹ 0.00003 1/°C ASTM E831 - Electrical Properties
Value Units Test Method / Conditions Surface Resistivity ¹¹ 1000 - 10000 Ω ASTM D257 - Impact Properties
Value Units Test Method / Conditions Izod Impact (Unnotched, at 23°C) ¹¹ 936 J/m ASTM D4812 Izod Impact (Notched, at 23°C) ¹¹ 75 J/m ASTM D256 Instrumented Dart Impact Total Energy (at 23°C) ¹¹ 6 J ASTM D3763 - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 150 °C - Drying Time ⁷ 4 - 6 Hrs - Front - Zone 3 Temperature ⁷ 380 - 400 °C - Middle - Zone 2 Temperature ⁷ 380 - 400 °C - Rear - Zone 1 Temperature ⁷ 370 - 380 °C - Mold Temperature ⁷ 175 - 190 °C - Back Pressure ⁷ 0.3 - 0.7 MPa - Screw Speed ⁷ 60 - 100 rpm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Country Availability
- Regional Availability