Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Flexural Modulus (at 1.3 mm/min, 50 mm span) ᶦ 15000 MPa ASTM D790 Flexural Modulus (at 2 mm/min) ᶦ 18100 MPa ISO 178 Flexural Strength (at 1.3 mm/min, 50 mm span) ᶦ 290 MPa ASTM D790 Flexural Strength (at 2 mm/min) ᶦ 340 MPa ISO 178 Tensile Modulus (at 1 mm/min) ᶦ 23000 MPa ISO 527 Tensile Modulus (at 5 mm/min) ᶦ 23000 MPa ASTM D638 Tensile Strain (Break, 5 mm/min) ᶦ 2.9 % ISO 527 Tensile Strain (Break, Type I, 5 mm/min) ᶦ 3.2 % ASTM D638 Tensile Stress (Break, 5 mm/min) ᶦ 230 MPa ISO 527 Tensile Stress (Break, Type I, 5 mm/min) ᶦ 205 MPa ASTM D638 - Physical Properties
Value Units Test Method / Conditions Density ¹¹ 1.24 g/cm³ ISO 1183 Moisture Absorption (at 23°C, 50% RH, Equilibrium) ¹¹ 0.8 - 0.9 % ISO 62-4 Water Absorption (at 23°C, saturated) ¹¹ 5 - 5.5 % ISO 62-1 Specific Gravity ¹¹ 1.24 - ASTM D792 Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ 0.1 - 0.3 % ASTM D570 Water Absorption (at 23°C, 24hrs) ¹¹ 0.9 - 1.2 % ASTM D570 Mold Shrinkage (flow) ᵍ ¹¹ 0.2 - 0.4 % SABIC method Mold Shrinkage (xflow) ᵍ ¹¹ 1 - 1.3 % SABIC method - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 261 °C ISO 75/Bf Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 251 °C ISO 75/Af Vicat Softening Temperature (Rate B/50) ¹¹ 250 °C ISO 306 Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ 0.000004 1/°C ISO 11359-2 Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ 0.000067 1/°C ISO 11359-2 Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ 0.000006 1/°C ISO 11359-2 Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ 0.000076 1/°C ISO 11359-2 Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ 261 °C ASTM D648 Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 251 °C ASTM D648 Vicat Softening Temperature (Rate B/120) ¹¹ 249 °C ASTM D1525 - Impact Properties
Value Units Test Method / Conditions Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ 65 kJ/m² ISO 179/1eU Charpy Impact (at 23°C, V-notch Edgew 80*10*3 sp=62mm) ¹¹ 9 kJ/m² ISO 179/1eA Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ 11 kJ/m² ISO 180/1A Izod Impact (Notched, at 23°C) ¹¹ 99 J/m ASTM D256 Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ 65 kJ/m² ISO 180/1U Izod Impact (Unnotched, at 23°C) ¹¹ 930 J/m ASTM D4812 - Injection Molding
Value Units Test Method / Conditions Back Pressure ⁷ 0.2 - 0.3 MPa - Drying Temperature ⁷ 80 °C - Drying Time (Cumulative) ⁷ 4 Hrs - Front - Zone 3 Temperature ⁷ 295 - 305 °C - Maximum Moisture Content ⁷ 0.15 - 0.25 % - Melt Temperature ⁷ 280 - 305 °C - Middle - Zone 2 Temperature ⁷ 280 - 295 °C - Mold Temperature ⁷ 95 - 110 °C - Rear - Zone 1 Temperature ⁷ 265 - 275 °C - Screw Speed ⁷ 30 - 60 rpm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᶦ mechanical properties have been tested after conditioning (48hrs/ 50%R.H.),The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Country Availability
- Regional Availability