Knowde Enhanced TDS
Identification & Functionality
- Plastics & Elastomers Functions
- Technologies
- Product Families
- Compatibility
Crestaform® Rapid has been designed to work with any UV LCD 3D printer that is open to 3rd party resins, including, but not limited to:
- Anycubic
- Elegoo
- Phrozen
- Creality
Features & Benefits
- Materials Features
- Product Benefits
Crestaform® Rapid comes with the following benefits:
- Excellent mechanical performance
- High reactivity and printing speed
- Rigorous test regime and best in industry quality assurance
- Globally available technical support
- Reputable manufacturer with over 100 years of experience and expertise
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Produt Application
Instructions to use the Crestaform® Rapid resin:
- Always shake or mix the resin thoroughly before use
- Open the container and pour the appropriate amount of resin into the tank according to the size of the printer model
- Make sure to not spill the resin onto the printer, LCD screen or anywhere outside of the resin tank
- If not used for a long time, please filter the resin and pour the resin into the storage container
Recommended cleaning
- Soak the print in a clean IPA bath for a minimum of 5 minutes. Alternatively, rinse the part with IPA until all the visible uncured resin has been removed. Reusing IPA in multiple cleans can reduce the cleanliness and clarity of a print.
- Leave the print to dry of any residual solvent prior to post-curing.
Recommended post-curing
- Post-cure every print for a minimum of 10 minutes under a dedicated curing UV light operating at 405nm wavelength. Alternatively, leave the print to cure for a minimum of 2 hours under direct sunlight.
- Temperature-assisted UV curing will increase the rigidity of the print.
Properties
- Physical Properties
- Mechanical Properties
- Notes
* Post-cured at 405nm UV light for 16 mins at 600C + 405mm UV
Value | Units | Test Method / Conditions | |
Viscosity | 1.2 - 2.0 | Poise | — |
Liquid Density | 1.05 - 1.07 | g/cm³ | — |
Value | Units | Test Method / Conditions | |
Tensile Strength* | 53 | MPa | ISO 527-2 Type 1A |
Tensile Modulus* | 2.4 | GPa | ISO 527-2 Type 1A |
Elongation (at Break)* | 3.2 | % | ISO 527-2 Type 1A |
Flexural Strength* | 86 | MPa | ISO 178 |
Flexural Modulus* | 2.5 | GPa | ISO 178 |
Heat Deflection Temperature (1.8MPa)* | 60 | °C | ISO 75-2, Method A |
Hardness* | 84 | Shore D | ISO 868 |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Typical Printing Parameters
Layer height: 50μm
Printing Temperature: 23°CLCD type
RGB UV LCD Monochromatic UV LCD
Base layer exposure time 50 - 80 sec 30 - 60 sec Normal layer exposure time 4 - 6 sec 1.5 - 2.5 sec
Packaging & Availability
- Packaging Type
- Packaging Information
Crestaform® Rapid is supplied in 1000 gr bottles. Bulk supply available.
Storage & Handling
- Handling Information
Do’s
- Always wear Personal Protection Equipment (PPE), protective eyewear and chemical nitrile gloves when handling resin.
- Shake the resin well every time before you use it or decant from the container.
- If spilled, please clean the spill immediately with paper towel, and Isopropyl alcohol.
- Store it in its original container at room temperature, away from children, untrained personnel, direct or indirect sunlight, heat sources, sparks and open flames.
- Use it in well ventilated rooms.
- Use every sensible preventive precaution to avoid skin contact, spillage of resin, eye contact or swallowing. Make note of Local Poison Centers availability.
Dont’s
- Expose resin to direct or indirect sunlight or UV light – while handling and storing the resin heat sources, sparks and open flame
- Touch the resin with bare hands. Always wear appropriate gloves. If skin contact occurs, wash it with soapy water. If you feel unwell, please consult immediately medical assistance
- Swallow the resin or printed objects
- Expose to children or pets
- Handle before completing training
- Expose persons sensitive to the resin components
- Inhale the resin fumes. Use only in well ventilated rooms or areas
- Pour the resin or used IPA into the draining system
- Storage Information
Crestaform® Rapid should be stored in the dark, in suitable, closed containers. It is recommended that the storage temperature should be between 15°C and 30°C. Ideally, containers should be opened only immediately prior to use. Keep out direct light/sunlight.