Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Polymer Name
- Technologies
Features & Benefits
- Labeling Claims
- Materials Features
- Features
- Selenis Maven MS 110 Ge is a copolyester with a slow crystallization rate and is suitable for the extrusion of heavy gage sheets, allowing for thicknesses up to 6mm, without crystallization occurring. Selenis Maven MS 110 Ge is the most adequate solution for flat sheets up to this thickness range, when excelent clarity, surface gloss, and neutral edge color are required.
- Selenis Maven MS 110 Ge is recommended when a combination of decorative capability, enhanced graphics, good impact strength at low temperatures and good chemical resistance to detergents and other household cleaning agents, are essential.
- Selenis Maven MS 110 Ge is easy to process on standard extrusion lines. Sheets made with Selenis Maven MS 110 Ge may be personalized though different methods of decoration, due to its inherent surface tension. Selenis Maven MS 110 Ge is BPA and styrene free, and is fully recyclable code 1.
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Application
- Indoor and outdoor sign boards
- Panels for graphic arts
- Roofing
- Flat displays
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Intrinsic Viscosity | 0.84 - 0.88 | dl/g | ISO 1628-5 |
| Color b* | max. 0 | — | ASTM D6290 |
| Color L* | min. 87 | — | ASTM D6290 |
| Acetaldehyde | max. 1 | ppm | ASTM F2013 |
| Melting Point | 225 - 235 | °C | ASTM D3418 |
| Crystallinity | min. 48 | % | ASTM D1505 |
| Specific Density Crystalline | min. 1.39 | g/cm3 | — |
| Bulk Density | 0.84 | g/cm3 | — |
| Moisture | max. 0.2 | % | — |
| Particle size | 270 - 370 | mg/20 chips | — |
| Pellet Shape | Cylindrical | — | — |
| Food Approval Pharmacopeia | YES | — | — |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Technical Details
Specifications
This table contains Selenis Maven MS 110 Ge characteristics and their methods of analysis. Some properties are subject to limits; others are presented with their typical values. Small variations of the typical values do not affect the application performance of the polymer.
All properties are measured under laboratory conditions by the analytical method shown. Limits in these specifications are applicable only to data obtained by the referenced test methods. Different methods or conditions of analysis may give rise to different values. A Certificate of Analysis, with representative average values of certain properties, can be sent to the customer when requested.
Processing
In order to obtain maximum product performance, Selenis Maven MS 110 Ge should be dried to achieve a moisture level below 0.004 % (40 ppm) before processing. Typical drying requirements include a dehumidifying air hopper dryer with regenerative desiccant beds, -40°C dew point air, 150oC drying temperature, and a residence time between 4-6 hours, with no temperature ramp.
Typical processing temperatures are between 265 – 275oC and should be chosen in function of the needs of the transformation technology.
Safety & Health
- Health and Safety Consideration
Read and follow all information presented in the Safety Data Sheet (SDS) for this product.
Storage & Handling
- Storage and Handling Conditions
- Selenis Maven MS 110 Ge is an inert material in storage and no hazards are likely to arise; however the polymer should be stored in an area properly protected from risk of fire.
- Selenis Maven MS 110 Ge should be stored in the original container, tightly closed in a dry, cool and well-ventilated place. Avoid direct light contact if the container is stored indoors.