Knowde Enhanced TDS
Identification & Functionality
- Agrochemical Functions
- CAS No.
- 9003-11-6
- EC No.
- 618-355-0
- Technologies
Features & Benefits
- Agrochemicals Features
Applications & Uses
- Markets
- Applications
- TOXIMUL 8322 is a 100% active nonionic surfactant used as an emulsifier in a variety of agricultural formulations.
- Emulsifiable Concentrates
- Microemulsions
- Suspension Concentrates
- Suspoemulsions
Properties
- Formulation Type
- Physical Form
- Appearance
- White to yellow solid (at 25°C)
- Soluble in
- Water, Methanol, Xylene
- Insoluble in
- Kerosene
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Acid Value | max. 1 | mg KOH/g | — |
| Melt Range | -6.96 to 48.21 | ºC | — |
| Cloud Point (1% in 10% NaCl solution) | 63 | °C | — |
| Melted Quantity (at 25ºC) | 6.79 | % | — |
| Density (at 50°C) | 1.06 | g/ml | — |
| Base | PPG/PEG | — | — |
| HLB | 15 | — | — |
| Flash Point | min. 223 | °C | PMCC Flash Point Tester |
| pH (in 1% aqueous) | 6 | — | — |
| Average Molecular Weight | 6500 | — | — |
| Pour Point | 35 | °C | — |
| Surface Tension (0.1% Aqueous) | 35.1 | dynes/cm | — |
| Regulated Volatile Organic Chemicals | 0 | % | U.S. EPA |
| Viscosity (at 45°C) | 1060 | cPs | — |
| Water Content | max. 0.5 | % | — |
Regulatory & Compliance
- Chemical Inventories
- Clearances
- The international inventories (country clearances) of TOXIMUL 8322 can be found in Section 15 of the Safety Data Sheet (SDS). It is the responsibility of the formulator to review the chemical control regulations for each country where the end product is intended to be sold or used.
- TOXIMUL 8322 is approved for use as an inert ingredient under U.S. EPA 40 CFR 180.940a, 180.940c and 180.960.
Technical Details & Test Data
- Melt Point Determination of TOXIMUL® 8322
- Rheology of TOXIMUL® 8322
Safety & Health
- Other Data DOT Classification
- Non-Hazardous
Packaging & Availability
- Packaging Type
Storage & Handling
- Storage & Handling
- Normal safety precautions (i.e., gloves and safety goggles) should be employed when handling TOXIMUL 8322. Contact with the eyes and prolonged contact with the skin should be avoided. Wash thoroughly after handling materials.
- Bulk Storage Information: Stainless steel and glass fiber-reinforced polyester tanks are recommended. Many oven-cured phenolic and epoxy/phenolic linings may also be used. Elevated storage temperature may be desirable to maintain ease of pumping. Temperatures up to 130°F (54°C) can be maintained for long periods of time without degradation of the product.
- TOXIMUL 8322 which has been stored in drums at temperatures below 75°F (24°C) may become a white paste. It can be cleared and fluidized by warming with a drum heater or in a steam room. Drums should be vented prior to heating to avoid excessive pressure build up. Product temperatures over 130°F (54°C) are not recommended.
- Workplace Exposure
Occupational exposure can occur primarily through skin contact or via inhalation of vapors and mists. Engineering controls, personal protective equipment, and other workplace practices should be used to control these exposures.