Products in Building Envelope & Roofing: Epoxy & Epoxy Derivatives

Circa 1850® NU-LUSTRE-57 cures to a thick, high gloss coat in about 24 hours. One coat is usually all that is needed to produce the desired finish. Additional coats may be applied after previous coats have cured for a minimum of 24 hours, lightly sanding in between coats. NU-LUSTRE-57 may be applied over almost any surface, rough or smooth. It may be applied over leather, wood, varnish, ceramics, rocks, stones, dried flowers, shells, and many others. It is ideal as a gap/cavity/crack filler. If in doubt, test a small sample of the item you wish to cover. NU-LUSTRE-57 will NOT ADHERE to silicone or wax. Before starting on your project, we strongly suggest you do a TEST PIECE to help you become familiar with this type of product, and for you to decide whether this will be the right product for the type of project you are doing.

Circa 1850® NU-LUSTRE-27 cures to a thick, high gloss coat in about 24 hours. One coat is usually all that is needed to produce the desired finish. Additional coats may be applied after previous coats have cured for a minimum of 24 hours, lightly sanding in between coats. NU-LUSTRE-27 may be applied over almost any surface, rough or smooth. It may be applied over leather, wood, varnish, ceramics, rocks, stones, dried flowers, shells, and many others. It is ideal as a gap/cavity/crack filler. If in doubt, test a small sample of the item you wish to cover. NU-LUSTRE-27 will NOT ADHERE to silicone or wax. Before starting on your project, we strongly suggest you do a TEST PIECE to help you become familiar with this type of product, and for you to decide whether this will be the right product for the type of project you are doing.

Circa 1850® NU-LUSTRE-55 cures to a thick, high gloss coat in about 24 hours. One coat is usually all that is needed to produce the desired finish. Additional coats may be applied after previous coats have cured for a minimum of 24 hours, lightly sanding in between coats. NU-LUSTRE-55 may be applied over almost any surface, rough or smooth. It may be applied over leather, wood, varnish, ceramics, rocks, stones, dried flowers, shells, and many others. It is ideal as a gap/cavity/crack filler. If in doubt, test a small sample of the item you wish to cover. NU-LUSTRE-55 will NOT ADHERE to silicone or wax. Before starting on your project, we strongly suggest you do a TEST PIECE to help you become familiar with this type of product, and for you to decide whether this will be the right product for the type of project you are doing.

Circa 1850® NU-LUSTRE-66 cures to a thick, high gloss coat in about 24 hours. One coat is usually all that is needed to produce the desired finish. Additional coats may be applied after previous coats have cured for a minimum of 24 hours, lightly sanding in between coats. NU-LUSTRE-66 may be applied over almost any surface, rough or smooth. It may be applied over leather, wood, varnish, ceramics, rocks, stones, dried flowers, shells, and many others. It is ideal as a gap/cavity/crack filler. If in doubt, test a small sample of the item you wish to cover. NU-LUSTRE-66 will NOT ADHERE to silicone or wax. Before starting on your project, we strongly suggest you do a TEST PIECE to help you become familiar with this type of product, and for you to decide whether this will be the right product for the type of project you are doing.

BECKOPOX™ EP 2340W/56WA is a liquid binder and resin within the epoxy and epoxy derivatives family, provided by CASE Ingredients. Notably APEO-free, formaldehyde-free, solvent-free, and VOC-free, it showcases enhanced chemical resistance and hardness. Tailored for the building and construction and paints and coatings sectors, its applications span decorative paints, building envelopes and roofing, and EIFS and insulation. This product, compatible with epoxies, is available as both an epoxy and waterborne coating, eliminating the need for a primer due to its primerless feature.

GP® CL-7003 phenolic resin from Georgia-Pacific Chemicals is a thermoplastic novolac. It is used as a crosslinking resin for epoxy and polyester resins. Its low phenol content, convenient softening point, and melt viscosity are conducive for use in powder coatings.

GP® CL-7004 phenolic resin from Georgia-Pacific Chemicals is a thermoplastic novolac. It is used as a crosslinking resin for epoxy and polyester resins. Its low phenol content, convenient softening point, and melt viscosity are conducive for use in powder coatings.

GP® CL-7002 phenolic resin from Georgia-Pacific Chemicals is a thermoplastic novolac. It is used as a crosslinking resin for epoxy and polyester resins. Its low phenol content, convenient softening point, and melt viscosity are conducive for use in powder coatings.

EBECRYL® 600, the diacrylate ester of bisphenol A epoxy resin, is distinguished by its light color and rapid cure response. Widely utilized in UV/EB applications, including inks, coatings, and overprint varnishes, EBECRYL® 600 stands out for its versatile performance. This product is particularly suitable for applications involving metal and wood substrates. Key features encompass faster cycle time, low energy consumption, long pot life, improved hardness, high gloss, improved chemical resistance, and low-temperature curing. It finds applications in decorative paints, wood coatings and finishes, EIFS, and insulation, utilizing radiation cure methods.

BECKOPOX™ EP 387W/52WA is an epoxy and epoxy derivative binder and resin by CASE Ingredients, labeled benzyl alcohol-free and VOC-free. Noted for its corrosion resistance, improved flexibility, and matte gloss capability, it serves the building and construction and paints and coatings sectors. Applications encompass decorative paints, EIFS, insulation, and industrial coatings on both metal and plastic substrates.

Kemperol® 022 is a two-component, high performance, cold-liquid applied, solvent-free, low VOC, crack-spanning resin for waterproofing beneath tile and stone applications.

CHS-EPOXY 514 is a Bisphenol A/F resin modified by monofunctional reactive diluent.

TouchStone™ T-2000 Epoxy is a two component, water cleanable, 100% solid epoxy adhesive compound developed for setting of ceramic tile and stone on horizontal or vertical surfaces.

Minchem PE120 is an epoxy-based acid-resistant primer or expansion joint material designed to seal and enhance existing concrete or metal surfaces. PE120 is a black plasticized epoxy system composed of a blended epoxy solution and hardener, combined with compatible carbon-pitch additives, to produce a permanently flexible compound with excellent adhesion to most dry surfaces.

DURACLAD C-507 HT is a high temperature tile adhesive.

Duresco NU 6110 T/NU 6110 V is a Glass fiber reinforced epoxy molding compound with very good mechanical properties for high temperature applications.

PanTINT® 73 are pigment dispersions for industrial solvent based epoxy coatings. They consist of industrial quality organic and inorganic pigments finely milled in Bisphenol A carrier resin. The pigments chosen for the PanTINT 73 exhibit color strength, durability, chemical resistance and light fastness. Most are suitable for interior and exterior applications. The epoxy carrier resin along with a proprietary additive package allow for high pigment solids and superior compatibility with a number of epoxy based systems. The 73 series’ will be compatible with a wide range of epoxy resin formulations for industrial, maintenance and architectural coating applications.

AmCoat Industries Rhino Rust Bond is a 100% solids epoxy primer designed to prime and encapsulate rusted metal surfaces. This 100% solids two component epoxy seals out air and moisture from the surface while providing a strong bond to ferrous metal surfaces. RHINO RUST BOND is a great alternative when sand blasting is not practical or cost effective. RUST BOND doesn't shrink resulting in very low surface tension, high spread rates, and great edge retention for metal edges and corners. This primer is typically used as part of two or three coat system utilizing RHINO URETHANE as the protective finish coat.

Northern Industries Hydro Seal 75 is a high strength, hydrophobic, breathing type, two-component, modified epoxy coating manufactured from a balanced ratio of fillers, and water extended resins and hardeners. Our exclusive formula combines flexibility with the hardness of epoxy resins.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

APCM DA 4092 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

PanTINT® 73 are pigment dispersions for industrial solvent based epoxy coatings. They consist of industrial quality organic and inorganic pigments finely milled in Bisphenol A carrier resin. The pigments chosen for the PanTINT 73 exhibit color strength, durability, chemical resistance and light fastness. Most are suitable for interior and exterior applications. The epoxy carrier resin along with a proprietary additive package allow for high pigment solids and superior compatibility with a number of epoxy based systems. The 73 series’ will be compatible with a wide range of epoxy resin formulations for industrial, maintenance and architectural coating applications.

True-Bond Gel™ is perfect for repairing cracked walls and even ceilings without the need for forms. Holds up to the same durability standards as all True-Bond™ materials. True-Bond Gel™ is concrete filler and bonder that will not separate from concrete. Resurfaces chipped and pitted concrete. Resists wear, corrosives, weather, impact. Bonds cracked curbing, masonry, swimming pools and is Waterproof. One application lasts for many years.

Biresin® CR131 is an epoxy resin system suitable for the production of high performance fiber reinforced composites parts and molds with thermal properties up to 130°C.

CoatMasters® 6007 HP is a two-component system based on high solids and high molecular weight epoxy resin and curing agent, for superior corrosion resistance from chemicals, such as acids and alkalis exposures. The epoxy coating mixture provides high crosslinking film density, adhesion, and does not contain any coal-tar. It is a self-priming coating applicable in multiple coats with excellent recoat-ability characteristics up to several days. It can be top-coated with polyurethanes and polyaspartic coating systems for specified finishes. The product is mainly used to provide superior corrosion and waterproofing protection on concrete structures and steel pipe, applied on either above or below ground installations. The filled systems provides higher abrasion and wear resistance and increased overall fluid resistance, ideal for filling voids or uneven surfaces on concrete applications, composite materials, and other metal substrates. It meets or exceeds the performance requirements of the US Army Corps of Engineers, Paint Specification C200. The CM 6007 Epoxy HP Coating (Polyamide Filled System) exhibits overall aged flexibility and outperforms other coal-tar formulated epoxy systems due to its increased recoatability period and higher temperature resistance to 400 °F. The higher solids characteristics and superior performance enables the material to be applied at a lower dry film thickness (DFT) thus providing increased coverage. It is available in various colors, such as black, blue, green, and red colors.

GacoFlex® E5990 is a 100% solids two-component penetrating epoxy sealer which forms a tight bond to concrete substrates and cures to form a clear hard continuous film.

CamCoat 2191 by Champion Advanced Materials (Singhania Group) is cycloaliphatic epoxy resin. It offers good weather resistance. It is suitable for use in coatings. CamCoat 2191 is used in outdoor applications.

Polygem 307 Ceramic Tile Adhesive is our industry standard epoxy tile adhesive. The 307 is a thixotropic gel that can adhere tiles applied to vertical and overhead surfaces. The Polygem 307 Ceramic Tile Adhesive is formulated to provide for a tenacious bond to most ceramic, metal, concrete, fiberglass or wood surfaces. Polygem 307 Ceramic Tile Adhesive is moisture resistant and will even cure underwater.

Northern Industries Adhere 101 is a water-based, heavy bodied, two component epoxy designed to seal above or below grade concrete and plywood sub-floors. Adhere 101 is supplied in natural white or a universal pigment may be used to create most pastel colors. ADHERE 101 is a white, heavy bodied, odorless, water-base epoxy designed for use as a waterproof primer for Northern Seamless Flooring. ADHERE 101 is primarily used as a primer for solvent base urethanes, all different types of epoxies, and a wide variety of acrylic paints and coatings. Because of outstanding chemical resistance and waterproof adhesion, ADHERE 101 is the choice of seamless flooring contractors, painting contractors, and waterproofing contractors.

VF 30™ is a low viscosity, high solids epoxy developed as a penetrating concrete primer for polyurea applications. VF 30 penetrates and strengthens the surface of the concrete, reduces pin-hole formations and provides a chemically reactive surface to accept VersaFlex polyurea systems. Adhesion is increased with the use of VF 30 by up to three times that of unprimed concrete.

CHS-EPOXY 501 is a Bisphenol A/F resin modified by monofunctional reactive diluent.

True-Bond CT™ is the answer for expansion joints or asphalt surfaces. From hairline cracks to crater-like potholes this product comes through every time. With up to 35% elasticity it is extremely flexible to temperature changes, yet incredibly hard and durable. Serves as an excellent waterproofing membrane for bridges and concrete overlays. Perfect for expansion joints, roof repairs and bridge footings, True-Bond CT™ boasts a minimum tensile elongation of 35%. True-Bond CT™ is asphalt filler and bonder that will not separate from bituminous surfaces. Repairs blacktop and concrete. Resists wear, corrosives, weather, impact. Waterproofing membrane for bridges and concrete overlays Bonds expansion joints and bridge footings. One application lasts for years.

Biresin® CR141 is a three component, anhydride cured, low viscosity epoxy resin system suitable for the production of high performance fi bre reinforced composites.

PanTINT® 73 are pigment dispersions for industrial solvent based epoxy coatings. They consist of industrial quality organic and inorganic pigments finely milled in Bisphenol A carrier resin. The pigments chosen for the PanTINT 73 exhibit color strength, durability, chemical resistance and light fastness. Most are suitable for interior and exterior applications. The epoxy carrier resin along with a proprietary additive package allow for high pigment solids and superior compatibility with a number of epoxy based systems. The 73 series’ will be compatible with a wide range of epoxy resin formulations for industrial, maintenance and architectural coating applications.

Duropoxi F is a two-component, 100% solids, chemical resistant, exterior grade epoxy adhesive. Non-sag gel epoxy. Flexible.

APCM DA 409U/S2-glass is a tough, versatile, modified epoxy resin prepreg that cures at 250ºF. The S-2 glass is a Zentron High Strength fiber. Standard weight is 260g/m2 with a 38% resin content. Other weights and resin contents available upon request.