Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
Applications & Uses
- Applications
- Cure Method
- Applications
- Field Assembly
- Dispense via dual cartridge
- Optics
- Active alignment of optics such as lenses, prisms, diodes, filters, etc. to opto-circuit
- Fiber Optics
- Field assembly of connectors and couplers
- Also suggested for fiber optic splicing
- Medical
- Adhesion to most metals, plastics, ceramics, and glasses found in tubing, substrates or housing.
- General
- Arts and crafts repair, restoration, and hobbyists.
- Field Assembly
- Instructions for Use
- Mix Resin: Hardener – 100:100 grams by weight or 1:1 by volume and vacuum degas.
- Cure as recommended achieving the desired properties.
- Typical cured properties were determined using recommended cure schedule.
- Some difference in properties may occur with the alternate or other cure schedules.
Properties
- Typical Cured Properties
- Handling Properties
| Value | Units | Test Method / Conditions | |
| Specific Gravity | 1.1 | — | — |
| Hardness | 80 | Shore D | — |
| Lap Shear Strength to Aluminium (at -55°C) | 2300 | psi | — |
| Lap Shear Strength to Aluminium (at 25°C) | 2800 | psi | — |
| Lap Shear Strength to Aluminium (at 95°C) | 150 | psi | — |
| Die Shear Strength | 1800 | psi | — |
| T-peel Strength | 45 | pli | — |
| Service Temperature Range | -55 to 125 | °C | — |
| Glass Transition Temperature (Tg) | min. 55 | °C | — |
| Coefficient of Linear Thermal Expansion (Below Tg) | 62 | 10⁻⁶/°C | — |
| Coefficient of Linear Thermal Expansion (Above Tg) | min. 200 | 10⁻⁶/°C | — |
| Dielectric Strength | 450 | Volts/mil | — |
| Dielectric Constant (at 1 kHz) | 3.2 | — | — |
| Dissipation Factor (at 1 kHz) | 0.02 | — | — |
| Volume Resistivity | 1x10¹³ | ohm-cm | — |
| Value | Units | Test Method / Conditions | |
| Adhesive | Part A | — | — |
| Hardener | Part B | — | — |
| Mix Ratio by Weight (Resin/Hardener) | 100/100 | — | — |
| Mix Ratio by Volume (Resin/Hardener) | 1/1 | — | — |
| Mixed Viscosity (at 25°C) | 20,000 - 30,000 | cps | — |
| Pot Life (at 25°C, 10 grams) | 10 - 12 | minutes | — |
Regulatory & Compliance
- Certifications & Compliance
- Certification
ISO-10993-5 compliant for cytotoxicity
Technical Details & Test Data
- Curing Information
Recommended Cure : 18-24 hours at 25°C
Safety & Health
- Safety Information
- For Industrial Use Only : Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning : Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet (MSDS) for additional health and safety information.
Packaging & Availability
- Packaging Type
- Availability
Available in 50mL, 200mL, and 400mL dual cartridges.
Storage & Handling
- Shelf Life
- 1 Year
- Storage & Shelf Life
One year when stored in unopened containers at an average temperature of 25°C.