Products

Mortartec Silicate™ DS is an industrial-grade repair mortar designed for dry shotcrete only applications to repair deteriorated concrete, where an early cure, high-density overlay is required. The material is a blend of Portland cement, graded silica sand, fibers and silica fume- incorporating corrosion and rust inhibitors. The mortar is spray applied, typically from ½” to 4” in depth (overhead and vertically) with incredible adhesion. Uses include repairing concrete walls, ceilings, brick, etc. Mortartec Silicate DS provides an extremely dense matrix and will accept coatings at earlier ages than typical Portland cement repair products.

CPP™ Sprayliner™ is two-component moisture insensitive, highly adhesive, chemical resistant, 100% solids, high strength and reinforced epoxy. Equal to “standard” CPP once cured, this version is packaged more conveniently for spray applicators seeking to utilize plural-component heated spray application. The material can be sprayed ultra-high build, between 1/16” - 1/4” (62.5 - 250 miles) per pass. Blended with reinforcing agents and various fibers, the Epoxytec CPP™ Sprayliner™ when cured creates reinforcement lining as a fiber-reinforced-polymer (FRP), with high strength and flexural properties for partially or fully deteriorated structures.

Mortartec Cermaico™ is a next-generation, epoxy-modified mortar. A highly advanced, formulated epoxy blend incorporating cutting-edge waterborne epoxide technology with proprietary engineered curing; combined with a specific balance of Portland cement, hardened ceramics, graded silica aggregate, synthetic fibers and silica fume to produce one of the most coveted mortars in the industrial market today. This results in a smooth mortar application with one of the hardest mortar surfaces in the industry once cured. The Mortartec Ceramico is industrial-grade and exhibits excellent performance properties unlike any mortar technology before it, with incredible adhesive properties, enhanced barrier sealing capabilities assisting with minimizing out-gassing and moisture vapor transmission (MVT).

Uroseal™ 45V polyurethane joint sealant is a two-components, aliphatic, chemically curing, 100% solid urethane sealant formulated as a high build coating / joint sealing system for vertical and overhead use. Once cured, the material forms a high-quality elastomeric sealant. Uroseal™ 45V is ideally suited for indoors or outdoors with use on concrete, wood, and most construction materials. Uroseal™ 45V produces a flexible, long‐lasting sealant with extraordinary adhesion, cohesion, and elasticity that resists deterioration caused by weathering, stress, movement, water, oils, and many chemicals. Provides corrosion protection and chemical resistance; and because of its mixed gel‐state, it is specially designed for use on vertical and overhead applications.

Mortartec Silicate™ is an industrial-grade blend of Portland cement, graded silica sand, fibers and silica fume. The mortar may be hand or spray applied, typically from ½” to 2” in depth. Uses include repairing concrete walls, ceilings, lining brick or concrete infrastructure, etc. Mortartec Silicate provides an extremely dense matrix and will accept coatings at earlier ages than typical Portland cement repair products.

CPP™ Gel™ is a two-component, high strength, extremely forgiving/tolerant, vertical and overhead, non-sag. fast set epoxy paste, packaged in a convenient 1-to-1 mix ratio to use as needed and restock. The Epoxytec CPP Gel provides a point-of-use application to save time and material. The material has a wide variety of applications and is often sought for concrete, steel, and other substrate repairs, filling, patching and as an adhesive. Epoxy-based material is a sealed and protective solution to combat corrosion.

CPP™ Gel: Crack Injection is two-component moisture insensitive, highly adhesive, chemical resistant, 100% solids, high strength epoxy paste and reinforced structural-grade epoxy. Similar to “standard” CPP once cured, this version is packaged more conveniently for Crack Injection and repair by extrusion. Contains no solvents. CPP™ Gel: Crack Injection bonds to concrete, steel, wood, brick, some plastics and most construction materials. Application temperature range is between 40°F and 100°F.