Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- Durable, long lasting finish.
- Excellent weather resistance.
- Good wear and abrasion resistance.
- UV stable for superior color retention.
- Outstanding hiding power.
- Environmentally friendly; VOC compliant.
- Fast drying for quicker recoating.
- Moisture vapor permeable – “breathable”.
- Good resistance to moisture absorption.
- Water-based for easy clean-up.
Applications & Uses
- Markets
- Compatible Substrates & Surfaces
- Usage
- As a color top coat for many Miracote products/systems.
- Stand-alone protective coating for concrete surfaces.
- For use in recoating other acrylic-based topcoats.
- Exterior and interior concrete and other surfaces.
- Horizontal, vertical and overhead applications.
- Installation Steps
- Surface preparation - All surfaces must be clean, sound, dry and free from any bond inhibiting substances including, but not limited to, grease, oil and any other contaminants or loosely adhered materials. For concrete substrates, a minimum concrete surface profile of CSP-1 to CSP-3 is required depending on overall substrate and application conditions, and coating or sealing requirements. At the time of application, minimum and maximum substrate temperatures must be 50°F (10°C) and 90°F (32.2°C), respectively. Temperatures outside these limits may negatively affect film formation, and lead to other application issues detrimental to performance and esthetics. When pressure-washing concrete always allow the substrate to thoroughly dry prior to application.
- Mixing - Prior to use, mechanically agitate or mix MiraGard Colorbond XL with drill and paddle at low speed to ensure any settlement of solids are brought back into suspension and to minimize air entrapment.
- Application - Using spray equipment: Apply one to two thin even coats depending on substrate porosity, performance and service conditions. The application of two coats is recommended and will always provide the best results. Do not over-apply or allow to puddle onto the surface. Using Brushes/Rollers: Apply MiraGard Colorbond XL in a continuous uniform film using conventional short nap high quality roller covers, lambswool applicators, or by natural bristle brush.
- For Best Results
- Always install a minimum 4’ by 4’ test area or job site mock-up for owner approval of acceptable color, texture, finish, adhesion, and any other critical requirement prior to proceeding.
- Always protect materials from excessive heat and cold, and precondition to room temperature as necessary.
- Regularly check wet film thickness with a mil gage. Monitor consumption to ensure correct application rates are obtained.
- The proper application of this product is the sole responsibility of the end user. Job site visits by Miracote representatives are only for observation and making recommendations, and do not assume any liability for supervision or quality control.
- It is recommended to apply in two coats at the published coverage rates. Do not apply in one thick coat.
- For enhanced chemical resistance, cleanability and stain resistance apply MiraGard HDWB clear acrylic sealer.
- Measure substrate temperatures to ensure that material is applied when temperatures are between 50°F (4.5°C) and 90°F (32.2°C) during placement.
Properties
- Typical Physical Properties
Value | Units | Test Method / Conditions | |
Solids Content | 55.0 | % | — |
Gloss 60° Gloss Meter | min. 75 | — | — |
Flexibility | Excellent | — | — |
Weathering | Excellent | — | — |
Abrasion Resistance | Excellent | — | — |
Curing Time (Dry to touch, 77°F) | 1.0 | hour | — |
Curing Time (Re-coat, 77°F) | 4.0 | hours | — |
Curing Time (Traffic, 77°F) | 24.0 | hours | — |
Temperature Limit (Continous) | 180.0 | °F | — |
Temperature Limit (Intermittent) | 255.0 | °F | — |
Technical Details & Test Data
- Coverage Rates
250-300 sq. ft./gal @ 6.4 to 5.3 mils (wft) per coat.
- Mix Ratio
Single component. Thoroughly mix prior to use.
- Limitations
- Apply only to clean, relatively dry surfaces.
- Must be applied only to properly prepared substrates.
- Seven to ten days cure required for peak hot tire resistance.
Packaging & Availability
- Packaging Type
- Packaging & Colours
- 1-gallon can
- 5-gallon pail
- 20 Standard Miracote Colors: Refer to color chart L-544
- Custom colors and color matching are available.
Storage & Handling
- Shelf Life & Storage
One year from the date of manufacture provided containers remain unopened and material is stored in a protected environment free from moisture, excessive heat, freezing temperatures, and direct sunlight.