Products

Ertalyte® TX Polyethylene Terephthalate Polyester PET is an unreinforced, semi-crystalline grade that offers superior dimensional stability, excellent wear resistance, a low coefficient of friction, high strength and rigidity, outstanding stain resistance, and great chemical and abrasion resistance. This grade is designed to withstand high pressure and velocity conditions and environments with soft metal and plastic mating surfaces where noise abatement is critical.Features:Superior dimensional stabilityExcellent wear resistanceLow coefficient of frictionHigh strength and rigidityOutstanding stain resistanceGreat chemical and abrasion resistanceBenefits:Withstands high pressure and velocity conditionsLow moisture absorption rate ensures mechanical and electrical properties are unaffected by moistureLow wear rate compared to unmodified polyestersIdeal for use in environments with soft metal and plastic mating surfaces where noise abatement is criticalApplications:High pressure and velocity applicationsFood processing and packagingPharmaceuticalOil and gas industriesMechanical precision parts that must endure high loads and wear conditions.

Ketron® Sterra™ HPV PEEK shapes are carbon fiber reinforced with graphite and PTFE lubricants. This gives them the lowest coefficient of friction and the best machinability of all PEEK materials. Due to Ketron® Sterra™ HPV PEEK’s combination of low wear, low friction, and high LPV, this grade is often chosen as a solution for service bearings, bushings, insulators, valves, and seals. As part of the Sterra™ product portfolio, this material contains recycled content and exhibits a significantly lower carbon footprint compared to similar materials derived from non-recycled feedstocks.

Ketron® Sterra™ 1000 PEEK is an unfilled, general-purpose grade known for its exceptional elongation and toughness. It is ideal for instrument and seal components, where ductility and inertness are crucial. Ketron® Sterra™ 1000 PEEK portfolio, featuring recycled content for a reduced carbon footprint compared to non-recycled materials.

Semitron® MPR 1000 - an advanced engineering material that is specially developed for use in the semiconductor and electronics industry. This material boasts excellent heat resistance and low erosion rates in plasma chambers, making it a top choice for vacuum chamber applications such as etch, CVD, and ion implant.Features:Longevity: Increased life in plasma chambers (up to 25X over polyimide in ozone)Clean: Low ionic metal content and low out-gassingValue: Lower overall cost in use compared to traditional materials used in vacuum chamber applications such as quartz, ceramics, and engineering plasticsBenefits:Long-lasting performance in plasma-based vacuum chambersLow maintenance and cost-effective solutionClean and efficient, suitable for semiconductor and electronics industryApplications:Clamp ringsTrench ringsScrewsPinsShower headsCentering pinsFocus ringsInsulatorsVacuum padsWafer guidesSemitron® MPR 1000 is a versatile material that is ideal for use in vacuum chamber applications within the semiconductor and electronics industry. With its outstanding heat resistance and low erosion rates, this material is a cost-effective and efficient solution that ensures longevity and clean performance in plasma-based vacuum chambers.

Ketron® Sterra™ CA30 PEEK is a 30% carbon fiber-reinforced grade that exhibits even higher stiffness, mechanical strength, and creep and wear resistance than Ketron GF30 PEEK. With a significantly reduced thermal expansion, optimum load carrying capabilities, and high thermal conductivity rates, Ketron® Sterra™ CA30 PEEK components are often favored for their ability to extend part life and rapidly dissipate heat in bearing applications. As part of the Sterra™ product portfolio, this material contains recycled content and exhibits a significantly lower carbon footprint compared to similar materials derived from non-recycled feedstocks.

Techtron® HPV PPS is a high-performance polymer that combines the excellent chemical and corrosion resistance of Polyphenylene Sulfide (PPS) with the added wear resistance and strength of glass fiber reinforcement and internal lubrication. This compression-molded material is designed to excel in demanding environments and applications where wear resistance and dimensional stability are required.Key features:Superior wear resistance: internally lubricated and glass fiber-reinforced, allowing it to withstand high loads and minimize wear and tearOutstanding chemical and hydrolysis resistance: suitable for use in harsh environments and chemicalsExcellent dimensional stability: minimal moisture absorption and low coefficient of linear thermal expansion, making it easy to maintain tight tolerancesGreat electrical insulating and dielectric propertiesLow coefficient of friction and inherent low flammabilityGlass fiber reinforced: increased strength and stiffness, ideal for wear componentsFood grade availableBenefits:Improved performance and durability of components in demanding environmentsIncreased resistance to chemicals, corrosion, and wearEnhanced precision and dimensional stabilityImproved electrical insulation and dielectric propertiesReduced friction and lower flammability riskMore cost-effective than advanced engineering plastics for certain applicationsApplications:Wear components such as bushings and bearings, CIP wash down parts, and pump, valve, and compressor applications in the aerospace, food processing, and oil and gas industries.Industrial equipment such as industrial drying and food processing ovens (bearings, rollers, etc.)Chemical process equipment (pump-, valve & compressor components)Electrical insulating systemsCost-effective alternative to advanced engineering plastics in certain applicationsTechtron® HPV is a versatile and reliable material that can help improve the performance and longevity of your products. It's available in a range of shapes and sizes, including food grade, making it easy to incorporate into your designs.

Fluorosint® 500 is an advanced polymer material that combines the excellent chemical resistance, low friction, and high temperature properties of PTFE (polytetrafluoroethylene) with added stability and wear resistance. This material is designed to excel in demanding applications where high performance, reliability, and tight dimensional control are required.Key features:Nine times greater resistance to deformation under load than unfilled PTFE: provides excellent wear and deformation resistanceLow coefficient of linear thermal expansion: approaches the expansion rate of aluminum and is 1/4 that of virgin PTFE, eliminating fit and clearance problems for designersPTFE base: provides excellent chemical resistance, low friction, and high temperature propertiesStock shapes available: allows for easy incorporation into your designs and efficient productionBenefits:High resistance to deformation under load, making it ideal for sealing applications where tight dimensional control is requiredLow coefficient of linear thermal expansion, eliminating fit and clearance problems in high temperature and dynamic environmentsEnhanced performance and durability of your products in high temperature and chemical environmentsImproved reliability and safety in critical applications.Applications:Sealing applications where tight dimensional control is requiredHigh temperature and dynamic environments where fit and clearance are a concernChemical processing industries where high chemical and hydrolysis resistance is neededAny application that requires stability and wear resistance in harsh environments.Fluorosint® 500 is a versatile and reliable material that can help improve the performance and longevity of your products. It's available in stock shapes as well as custom shapes, it allows for efficient production and the ability to create complex geometries. With its added stability and wear resistance, Fluorosint® 500 is an excellent choice for applications in chemical processing, aerospace, automotive and other industries where tight dimensional control and high-performance sealing are required.

Ketron® 1000 PEEK is a high-performance polymer that offers excellent mechanical properties and chemical resistance. It is widely used in a variety of applications where high strength and stiffness, low friction, and excellent dimensional stability are required. This material is ideal for instrument and seal components, where its high elongation and toughness make it an excellent choice. Its non-toxic and biocompatible properties make it suitable for use in medical and food processing applications.   Key features: High strength and stiffness Low friction Excellent dimensional stability High elongation and toughness EU 10/2011 and FDA compliant   Benefits: Improved performance and durability of components Increased resistance to chemicals and high temperatures Enhanced biocompatibility and safety in medical and food processing applications Greater design flexibility and compatibility with a wide range of applications and industries   Application: Structural parts: Ketron® PEEK is often used for structural components that are subject to high temperatures and chemical exposure. For example, it is commonly used for vacuum wand handles in semiconductor manufacturing. Bushings, bearings, seals, and back-up rings: Ketron® PEEK is an excellent choice for components that are subject to wear and tear. Its low coefficient of friction and high strength make it suitable for use in a wide range of applications, from aircraft to oil field drilling.   Ketron® 1000 PEEK is available in a range of shapes and sizes, making it easy to incorporate into your designs. It is a versatile and reliable material that can help improve the performance and longevity of your products.

TIVAR® Sterra™ UHMW-PE shapes are produced from reprocessed industrial UHMW materials and repurposed for use in a variety of industries, such as construction and heavy equipment, agriculture and grain handling, bulk material and parcel handling, automotive, and transportation. As a premium grade that is both economical and eco-friendly, TIVAR® Sterra™ UHMW-PE components exhibit excellent abrasion and corrosion resistance, outstanding impact strength, minimal moisture absorption, and a low coefficient of friction. For these reasons, TIVAR® Sterra™ UHMW-PE is often a favored solution for wear and outrigger pads, strips, rails, and guides, rollers, conveyors, chutes, hoppers, impact plates, and asphalt equipment components. As part of the Sterra™ product portfolio, this material contains recycled content and exhibits a significantly lower carbon footprint compared to similar materials derived from non-recycled feedstocks.

Duratron® D7015G PI Polyimide is a high-performance bearing grade material that offers exceptional temperature and wear resistance. With a low coefficient of friction, this material is ideal for use in applications where high loads and speeds are a critical factor.Features:15% graphite added for long wear and frictionSuperior temperature and wear resistanceLow coefficient of frictionMaintains performance abilities with or without lubricationBenefits:Excellent choice for bearing, bushing, and seal applications where higher loads or speeds are a significant factorProvides long-lasting performance in harsh environmentsLow maintenance and long-lasting partsApplications:Bearings and bushings in high-temperature environmentsSeals for high-speed or high-load applicationsMachine parts and components in harsh environments where temperature and wear resistance are needed.

Duratron® T5530 PAI is a high-performance, glass-reinforced polyamide-imide material that offers exceptional rigidity, retention of stiffness, low thermal expansion, and outstanding load-carrying capabilities. This 30% glass-reinforced grade is ideal for structural applications in the semiconductor, electronics, and aerospace industries, where high strength, stiffness, and dimensional stability are required.Features:High rigidity and retention of stiffnessLow thermal expansionOutstanding load-carrying capabilities30% glass reinforced for added strength and stiffnessBenefits:Suitable for structural applications in harsh environmentsOffers exceptional dimensional stability up to 260°CIdeal for precision parts in the electronic and semiconductor industriesApplications:Aerospace and defenseSemiconductor and electronicsIndustrial machinery and equipmentMedical devicesPrecision parts in high-temperature environmentsNote: The suitability of Duratron T5530 PAI for sliding parts should be carefully evaluated as the glass fibers may cause abrasion to the mating surface.

Duratron® CU60 PBI, the ultimate engineering plastic for high-performance applications. This advanced material is made from Polybenzimidazole (PBI) and is the highest performing engineering plastic offered by Mitsubishi Chemical Advanced Materials. With superior mechanical properties, heat resistance, and mechanical property retention over 400°F / 205°C, Duratron® CU60 PBI is the ideal choice for applications where extreme temperatures and high loads are present.Features:Superior mechanical properties, heat resistance, and mechanical property retention over 400°F / 205°CBetter wear resistance and load carrying capabilities at extreme temperatures than any other reinforced or unreinforced advanced engineering plastic"Clean" in terms of ionic impurity and does not outgas (except water)Excellent ultrasonic transparency, making it an ideal choice for probe tip lenses in ultrasonic measuring equipmentExcellent thermal insulation, other plastics in melt do not stick to Duratron CU60 PBIBenefits:Duratron® CU60 PBI offers unmatched performance in high-heat applications, making it ideal for high heat bushings, connectors, valve seats, and probe tip lenses in semiconductor manufacturingIts superior wear resistance and load carrying capabilities make it a great choice for aerospace and other high-performance industriesIts "clean" characteristics make it ideal for use in vacuum chamber applications in semiconductor manufacturingIts excellent thermal insulation and non-stick properties make it ideal for contact seals and insulator bushings in plastic production and molding equipmentDuratron CU60 PBI is an ideal replacement for metals and ceramics in pump components, valve seats, bearings, rollers, and high-temperature insulatorsApplications:High-performance vacuum chamber applications in semiconductor manufacturingAerospace and other high-performance industriesHigh heat bushings, connectors, valve seats, and probe tip lensesContact seals and insulator bushings in plastic production and molding equipmentPump components, valve seats, bearings, rollers, and high-temperature insulatorsCritical components to decrease maintenance costs and to gain valuable production "uptime".

Nylatron® SA Flame Retardant (FR) Polyamide PA66 shapes were specifically developed to meet the requirements of the plastic flammability test, as outlined in UL 94 and EN 45545-2 regulations. This grade of Nylatron® is designed for applications within the transportation and railway markets, and is ideal for use in cable holders, clamps, channels, and connections/sockets.Features:Universally flame retardantFully compliant with REACHLow moisture absorptionAbsence of heavy metals and halogens – RoHS compliantBenefits:Meets V-0 criteria from a thickness of 1mmCompliant with the EN 45545-2 regulation, a standard specific to railway applicationsSuitable for use in transportation and railway marketsApplications:Cable holdersClampsChannelsConnections / socketsAdditional Note: Parts manufactured from Nylatron 66SA FR can be disposed according to WEEE.

Nylatron® FST Polyamide PA66 is a fire, smoke, and toxicity retardant engineering plastic that is designed to withstand extreme temperatures up to 347° F / 175° C. This grade is JAR / FAR 25.853 compliant, making it the first engineering plastic to achieve this standard. It is specifically developed for aircraft interior environments and is often used as a replacement for metal parts in various applications such as brackets, seal bushings, slide rails, and duct seals.Features:Fire, smoke, and toxicity retardantWithstands temperatures up to 347° F / 175° CJAR / FAR 25.853 compliantBenefits:Provides superior fire safety for aircraft interior environmentsCan withstand extreme temperatures, making it suitable for high-temperature applicationsMeets industry standards for fire and smoke safety, making it a reliable and safe choice for various applicationsApplications:Aircraft interior environmentsBracketsSeal bushingsSlide railsDuct sealsOther high-temperature and fire safety applications.

Fluorosint® 135 is an advanced polymer material that combines the excellent chemical resistance, low friction and high temperature properties of PTFE (polytetrafluoroethylene) with the added low coefficient of friction, strength, stiffness and high pressure velocity capabilities. This material is designed to excel in demanding applications where high performance and reliability are required.Key features:Low coefficient of friction: provides excellent wear and deformation resistanceHigh strength and stiffness: provides superior mechanical performance at elevated temperaturesPTFE base: provides excellent chemical resistance, low friction and high temperature propertiesStock shapes available: allows for easy incorporation into your designs and efficient productionHigh temperature resistance: able to maintain stability and strength in high temperature environments.Benefits:Low coefficient of friction, making it ideal for seals, bearings, and washer applicationsImproved strength and stiffness of components in demanding environments and high temperaturesIncreased resistance to wear and tear, impact and high temperaturesEnhanced performance and durability of your products in high temperature and chemical environmentsImproved reliability and safety in critical applications.Applications:Low friction seals, bearings and washer applicationsHigh-performance wear applications where extreme conditions are present such as high temperature, pressure and chemical exposureComponents that require high strength and stiffness, such as gears, bearing components, and bushings in high temperature environmentsIndustrial and manufacturing equipment where high strength and stiffness is needed, such as in high temperature environments and chemical processesComponents that need high chemical resistance, low friction, and high temperature properties such as valves, pumps, and heat exchangers.Fluorosint® 135 is a versatile and reliable material that can help improve the performance and longevity of your products. It's available in stock shapes as well as custom shapes, it allows for efficient production and the ability to create complex geometries. It's also important to mention that the temperature and chemical resistance can vary depending on the grade of PTFE used as well as other additives, always consult with the manufacturer for the exact properties of the final material.

Duratron® D7000 PI Polyimide shapes - a high-performance material ideal for demanding applications that require exceptional thermal resistance, low wear and friction, strength, and impact resistance. With superior electrical and thermal insulation properties, outstanding mechanical performance, great chemical resistance, and outstanding dimensional stability, Duratron® D7000 PI is an ideal solution for designs that reduce weight, extend service life, and reduce overall costs.Features:Superior electrical and thermal insulation propertiesOutstanding mechanical performanceGreat chemical resistanceHigh strength and toughnessOutstanding dimensional stabilityBenefits:Ideal for designs that reduce weightExtends service life before maintenance or replacementReduces overall costs by increasing process uptimeApplications:AerospaceTransportationIndustrialDuratron® D7000 PI is available in stock shapes and direct formed parts, perfect for smaller series and designs where tolerances and geometry of the end part require machining. The material is also available in Hot Compression Molded (HCM) shapes, providing designers with the greatest economy and flexibility.