company tower banner
SABIC's Specialties Business Company Logo

LNP™ LUBRICOMP™ Compound IFL21

1 of 365 products in this brand
LNP LUBRICOMP IFL21 compound is based on Nylon 6/12 resin containing 5% glass fiber, 10% PTFE. Added features of this grade include: Wear Resistant.

Polymer Name: Polyamide 612 (PA 612)

Processing Methods: Injection Molding

Fillers Included: Glass Fiber, PTFE

Additives Included: Heat Stabilizer, Lubricant (PTFE), Mold Release Agent

Flexural Modulus: 3020.0 - 3020.0 MPa

Technical Data Sheet

Knowde Enhanced TDS

Identification & Functionality

Chemical Family
Fillers Included
Plastics & Elastomers Functions
Technologies

Features & Benefits

Applications & Uses

Plastics & Elastomers Processing Methods

Properties

Mechanical Properties
ValueUnitsTest Method / Conditions
Tensile Stress (Break) ¹¹70MPaASTM D638
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹63MPaASTM D638
Tensile Strain (Break) ¹¹2.8%ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹63MPaASTM D638
Tensile Modulus (at 50 mm/min) ¹¹3620MPaASTM D638
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹2.2%ASTM D638
Flexural Stress ¹¹110MPaASTM D790
Flexural Stress ¹¹97MPaISO 178
Tensile Strain (Break, Type I, 5 mm/min) ¹¹2.2%ASTM D638
Flexural Modulus ¹¹3330MPaASTM D790
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹99MPaASTM D790
Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹98MPaASTM D790
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹2870MPaASTM D790
Tensile Stress (Yield, 5 mm/min) ¹¹64MPaISO 527
Tensile Stress (Break, 5 mm/min) ¹¹64MPaISO 527
Tensile Strain (Yield, 5 mm/min) ¹¹2.4%ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹2.4%ISO 527
Tensile Modulus (at 1 mm/min) ¹¹3500MPaISO 527
Flexural Modulus (at 2 mm/min) ¹¹3020MPaISO 178
Physical Properties
ValueUnitsTest Method / Conditions
Density ¹¹1.17g/cm³ASTM D792
Specific Gravity ¹¹1.17-ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹0.2%ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹0.4 - 0.7%ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹0.8 - 1.1%ASTM D955
Wear Factor Washer ¹¹12910^-10 in^5-min/ft-lb-hrASTM D3702 Modified: Manual
Wear Factor Ring ¹¹710^-10 in^5-min/ft-lb-hrASTM D3702 Modified: Manual
Dynamic COF ¹¹0.36-ASTM D3702 Modified: Manual
Static COF ¹¹0.32-ASTM D3702 Modified: Manual
Moisture Absorption (at 23°C, 50% RH) ¹¹0.25%ISO 62
Thermal Properties
ValueUnitsTest Method / Conditions
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹183°CASTM D648
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹200°CASTM D648
Coefficient of Thermal Expansion (at -30°C to 30°C, flow) ¹¹0.0000821/°CASTM D696
Coefficient of Thermal Expansion (at -30°C to 30°C, xflow) ¹¹0.0001251/°CASTM D696
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹197°CISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹162°CISO 75/Af
Impact Properties
ValueUnitsTest Method / Conditions
Izod Impact (Unnotched, at 23°C) ¹¹270J/mASTM D4812
Izod Impact (Notched, at 23°C) ¹¹30J/mASTM D256
Multi-Axial Impact ¹¹1JISO 6603
Instrumented Dart Impact Total Energy (at 23°C) ¹¹3JASTM D3763
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹17kJ/m²ISO 180/1U
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹3kJ/m²ISO 180/1A
Injection Molding
ValueUnitsTest Method / Conditions
Drying Temperature ⁷80°C-
Drying Time ⁷4Hrs-
Maximum Moisture Content ⁷0.12 - 0.2%-
Melt Temperature ⁷270 - 275°C-
Front - Zone 3 Temperature ⁷270 - 280°C-
Middle - Zone 2 Temperature ⁷260 - 270°C-
Rear - Zone 1 Temperature ⁷255 - 265°C-
Mold Temperature ⁷65 - 95°C-
Back Pressure ⁷0.2 - 0.3MPa-
Screw Speed ⁷30 - 60rpm-
Note
  • ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
  • ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
  • ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
 

Packaging & Availability

Regional Availability
  • Americas
  • Asia
  • North America