LNP THERMOCOMP™ Compound - MF006SXP - SABIC's Specialty

Identification & Functionality

Features & Benefits

Labeling Claims: No Added PFAS
Materials Features: Cost Effective,
Good Mold Release,
Heat Stabilized,
High Modulus,
High Stiffness,
No Added PFAS

Applications & Uses

Markets: Consumer Goods,
Electrical & Electronics,
Personal Care,
Printing & Packaging
Applications: Consumer Goods — Appliances & Electronics
Electrical & Electronics — Devices & Assemblies
Consumer Electronics,
Displays
Printing & Packaging — Packaging
Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
Applicators & Accessories
Electrical & Electronics — Parts & Components
Connectors,
Switches & Relays
Consumer Goods — Sports & Recreation
Plastics & Elastomers End Uses: Cell Phones,
Computer Components,
Consumer Applications,
Containers,
Displays,
Electrical Components,
Electrical/Electronic Applications,
Personal Accessories,
Sporting Goods,
Tablets
Plastics & Elastomers Processing Methods: Injection Molding

Properties

Flame Rating: UL 94 HB
Mechanical Properties
Physical Properties
Thermal Properties
Electrical Properties
Impact Properties
Injection Molding
Flame Characteristics
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.

⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.

¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

	Value	Units	Test Method / Conditions
Tensile Stress (Break) ¹¹	88	MPa	ASTM D638
Tensile Stress (Break) ¹¹	91	MPa	ISO 527
Tensile Stress (Yield, 50 mm/min) ¹¹	81	MPa	ISO 527
Tensile Strain (Break) ¹¹	3	%	ASTM D638
Tensile Strain (Break) ¹¹	3.2	%	ISO 527
Tensile Strain (Yield, 50 mm/min) ¹¹	2.6	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	7600	MPa	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	5700	MPa	ISO 527
Tensile Modulus (at 50 mm/min) ¹¹	7300	MPa	ASTM D638
Flexural Stress (Yield, at 2 mm/min) ¹¹	105	MPa	ISO 178
Flexural Stress ¹¹	159	MPa	ISO 178
Flexural Stress ¹¹	1.39E+02	MPa	ASTM D790
Flexural Modulus (at 2 mm/min) ¹¹	5100	MPa	ISO 178
Flexural Modulus ¹¹	8700	MPa	ISO 178
Flexural Modulus ¹¹	6200	MPa	ASTM D790

	Value	Units	Test Method / Conditions
Density ¹¹	1.13	g/cm³	ASTM D792
Density ¹¹	1.13	g/cm³	ISO 1183
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.02	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.5	%	ASTM D955
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.5	%	ISO 294
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	1	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.96	%	ISO 294
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.03	%	ISO 62

	Value	Units	Test Method / Conditions
Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹	0.000035	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹	0.000126	1/°C	ISO 11359-2
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	152	°C	ISO 75/Af
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	136	°C	ISO 75/Af
Relative Temperature Index (Electrical) ᵖ ¹¹	65	°C	UL 746B
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹	65	°C	UL 746B
Relative Temperature Index (Mechanical without impact) ᵖ ¹¹	65	°C	UL 746B
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	160	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	150	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000264	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000264	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000598	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000597	1/°C	ASTM E831

	Value	Units	Test Method / Conditions
Comparative Tracking Index (UL, PLC) ¹¹	0	PLC Code	UL 746A
Hot Wire Ignition (PLC 2) ¹¹	min. 3	mm	UL 746A
Hot Wire Ignition (PLC 3) ¹¹	min. 1	mm	UL 746A
High Ampere Arc Ignition (PLC 1) ¹¹	min. 1.5	mm	UL 746A
High Ampere Arc Ignition (PLC 3) ¹¹	min. 1	mm	UL 746A
High Voltage Arc Track Rate (PLC) ¹¹	1	PLC Code	UL 746A
Arc Resistance (Tungsten, PLC) ¹¹	6	PLC Code	ASTM D495

	Value	Units	Test Method / Conditions
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	35	kJ/m²	ISO 180/1U
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	45	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80104, at 23°C) ¹¹	11	kJ/m²	ISO 180/1A
Izod Impact (Notched, 80104, at 23°C) ¹¹	9	kJ/m²	ISO 180/1A
Izod Impact (Unnotched, at 23°C) ¹¹	704	J/m	ASTM D4812
Izod Impact (Notched, at 23°C) ¹¹	117	J/m	ASTM D256
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹	3	J	ASTM D3763
Multi-Axial Impact ¹¹	2	J	ISO 6603

	Value	Units	Test Method / Conditions
UL Recognized (94HB Flame Class Rating) ᵖ	min. 1	mm	UL 94

Regulatory & Compliance

Packaging & Availability

LNP™ THERMOCOMP™ Compound MF006SXP