Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Electrical Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
| Value | Units | Test Method / Conditions | |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 160 | MPa | ISO 527 |
| Tensile Stress (Break) ¹¹ | 165 | MPa | ISO 527 |
| Tensile Stress (Break) ¹¹ | 128 | MPa | ISO 527 |
| Tensile Stress (Break) ¹¹ | 129 | MPa | ASTM D638 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 3.7 | % | ISO 527 |
| Tensile Strain (Break) ¹¹ | 2.8 | % | ASTM D638 |
| Tensile Strain (Break) ¹¹ | 2.9 | % | ISO 527 |
| Tensile Strain (Break) ¹¹ | 3 - 5 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 9500 | MPa | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 8500 | MPa | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 8580 | MPa | ISO 527 |
| Tensile Modulus (at 50 mm/min) ¹¹ | 8750 | MPa | ASTM D638 |
| Flexural Stress (Break, 2 mm/min) ¹¹ | 230 | MPa | ISO 178 |
| Flexural Stress ¹¹ | 225 | MPa | ISO 178 |
| Flexural Stress ¹¹ | 201 | MPa | ASTM D790 |
| Flexural Stress ¹¹ | 2.03E+02 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 8000 | MPa | ISO 178 |
| Flexural Modulus ¹¹ | 6960 | MPa | ASTM D790 |
| Flexural Modulus ¹¹ | 8100 | MPa | ISO 178 |
| Hardness (Rockwell L) ¹¹ | 111 | — | ISO 2039-2 |
| Value | Units | Test Method / Conditions | |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.2 - 0.4 | % | ISO 294 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.2 - 0.5 | % | ASTM D955 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.17 - 0.5 | % | ISO 294 |
| Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ | 1 - 1.2 | % | ASTM D955 |
| Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ | 1 - 1.2 | % | ISO 294 |
| Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ | 0.9 - 1.3 | % | ISO 294 |
| Density ¹¹ | 1.37 | g/cm³ | ISO 1183 |
| Density ¹¹ | 1.37 | g/cm³ | ASTM D792 |
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹ | 0.2 - 0.4 | % | SABIC method |
| Mold Shrinkage (on Tensile Bar, xflow) ᵍ ¹¹ | 0.8 - 1.1 | % | SABIC method |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.86 | % | ASTM D570 |
| Water Absorption (at 23°C, saturated) ¹¹ | 6.5 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 1.8 | % | ISO 62 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 1.53 | % | ISO 62 |
| Value | Units | Test Method / Conditions | |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 203 | °C | ISO 75/Af |
| Relative Temperature Index (Electrical) ᵖ ¹¹ | 130 | °C | UL 746B |
| Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 70 | °C | UL 746B |
| Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 85 | °C | UL 746B |
| Thermal Conductivity ¹¹ | 0.33 | W/m-°C | ISO 8302 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.000025 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000085 | 1/°C | ISO 11359-2 |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 219 | °C | ASTM D648 |
| Ball Pressure Test (at 123°C to 127°C) ¹¹ | Pass | — | IEC 60695-10-2 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 206 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.0000305 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.0000306 | 1/°C | ISO 11359-2 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 215 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.0000673 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.0000672 | 1/°C | ISO 11359-2 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 215 | °C | ISO 306 |
| Heat Deflection Temperature/Be (at 0.45MPa, Edgew 120*10*4, sp=100mm) ¹¹ | 220 | °C | ISO 75/Be |
| Heat Deflection Temperature/Ae (at 1.8 Mpa, Edgew 120*10*4, sp=100mm) ¹¹ | 205 | °C | ISO 75/Ae |
| Value | Units | Test Method / Conditions | |
| Comparative Tracking Index (UL, PLC) ¹¹ | 0 | PLC Code | UL 746A |
| Hot Wire Ignition (PLC 2) ¹¹ | min. 3 | mm | UL 746A |
| Hot Wire Ignition (PLC 3) ¹¹ | min. 1.5 | mm | UL 746A |
| High Ampere Arc Ignition (PLC 0) ¹¹ | min. 1.5 | mm | UL 746A |
| High Voltage Arc Track Rate (PLC) ¹¹ | 1 | PLC Code | UL 746A |
| Arc Resistance (Tungsten, PLC) ¹¹ | 5 | PLC Code | ASTM D495 |
| Volume Resistivity ¹¹ | min. 1.E+16 | Ω.cm | IEC 60093 |
| Surface Resistivity (ROA) ¹¹ | min. 1.E+16 | Ω | IEC 60093 |
| Dielectric Strength (in oil, at 3.2mm) ¹¹ | 20 | kV/mm | IEC 60243-1 |
| Relative Permittivity (1 MHz) ¹¹ | 3.4 | — | IEC 60250 |
| Dissipation Factor (at 50/60 Hz) ¹¹ | 0.0061 | — | IEC 60250 |
| Dissipation Factor (at at 1 MHz) ¹¹ | 0.016 | — | IEC 60250 |
| Comparative Tracking Index ʳ ¹¹ | 500 | V | IEC 60112 |
| Comparative Tracking Index (M) ʳ ¹¹ | 375 | V | IEC 60112 |
| Relative Permittivity (50/60 Hz) ¹¹ | 3.6 | — | IEC 60250 |
| Value | Units | Test Method / Conditions | |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 85 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 55 | kJ/m² | ISO 180/1U |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 8 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 11 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 15 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -20°C) ¹¹ | 10 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 9 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -40°C) ¹¹ | 9 | kJ/m² | ISO 180/1A |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 11 | kJ/m² | ISO 179/1eA |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 827 | J/m | ASTM D4812 |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 9 | kJ/m² | ISO 179/1eA |
| Izod Impact (Notched, at 23°C) ¹¹ | 117 | J/m | ASTM D256 |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 90 | kJ/m² | ISO 179/1eU |
| Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ | 9 | J | ASTM D3763 |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 75 | kJ/m² | ISO 179/1eU |
| Multi-Axial Impact ¹¹ | 2 | J | ISO 6603 |
| Value | Units | Test Method / Conditions | |
| Drying Temperature ⁷ | 80 | °C | — |
| Drying Temperature ⁷ | 75 - 85 | °C | — |
| Drying Time ⁷ | 4 | Hrs | — |
| Drying Time ⁷ | 4 - 6 | Hrs | — |
| Maximum Moisture Content ⁷ | 0.15 - 0.25 | % | — |
| Maximum Moisture Content ⁷ | 0.2 | % | — |
| Melt Temperature ⁷ | 250 - 280 | °C | — |
| Melt Temperature ⁷ | 265 - 275 | °C | — |
| Melt Temperature ⁷ | 255 - 265 | °C | — |
| Front - Zone 3 Temperature ⁷ | 250 - 280 | °C | — |
| Front - Zone 3 Temperature ⁷ | 275 - 290 | °C | — |
| Front - Zone 3 Temperature ⁷ | 250 - 260 | °C | — |
| Nozzle Temperature ⁷ | 240 - 270 | °C | — |
| Middle - Zone 2 Temperature ⁷ | 265 - 275 | °C | — |
| Middle - Zone 2 Temperature ⁷ | 250 - 260 | °C | — |
| Middle - Zone 2 Temperature ⁷ | 250 - 280 | °C | — |
| Rear - Zone 1 Temperature ⁷ | 250 - 260 | °C | — |
| Rear - Zone 1 Temperature ⁷ | 250 - 280 | °C | — |
| Rear - Zone 1 Temperature ⁷ | 245 - 255 | °C | — |
| Mold Temperature ⁷ | 70 - 120 | °C | — |
| Mold Temperature ⁷ | 80 - 95 | °C | — |
| Mold Temperature ⁷ | 55 - 95 | °C | — |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa | — |
| Back Pressure ⁷ | 0.2 - 0.3 | MPa | — |
| Hopper Temperature ⁷ | 60 - 80 | °C | — |
| Screw Speed ⁷ | 30 - 60 | rpm | — |
| Value | Units | Test Method / Conditions | |
| UL Recognized (94HB Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
| UV-light (Water exposure/immersion) ᵖ | F2 | — | UL 746C |
| UL Compliant (94HB Flame Class Rating) ᵖ | 0.75 | mm | UL 94 by SABIC-IP |
| Glow Wire Flammability Index (passes at 650°C) ʳ ᵖ | 2 | mm | IEC 60695-2-12 |
| Oxygen Index (LOI) ᵖ | 25 | % | ISO 4589 |
| FMVSS Burning Speed (Thickness 2 mm) ᵖ | 6 | mm/min | FMVSS 302 |
| FMVSS Burning Speed (Thickness 3 mm) ᵖ | 2 | mm/min | FMVSS 302 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability