LNP THERMOCOMP™ Compound - QC006 - SABIC's Specialty

Identification & Functionality

Features & Benefits

Labeling Claims: No Added PFAS
Materials Features: Cost Effective,
ESD Protection,
Electrically Conductive,
High Stiffness,
High Strength,
Light Weight,
Low Moisture Absorption,
No Added PFAS

Applications & Uses

Markets: Building & Construction,
Consumer Goods,
Electrical & Electronics,
Personal Care,
Printing & Packaging
Applications: Consumer Goods — Appliances & Electronics
Building & Construction — Decorative Materials & Finishes
Artificial Turf
Electrical & Electronics — Devices & Assemblies
Consumer Electronics,
Displays
Consumer Goods — Lawn & Garden
Printing & Packaging — Packaging
Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
Applicators & Accessories
Electrical & Electronics — Parts & Components
Connectors,
Switches & Relays
Consumer Goods — Sports & Recreation
Plastics & Elastomers End Uses: Appliances,
Building Materials,
Cell Phones,
Commercial Appliance,
Computer Components,
Consumer Applications,
Containers,
Displays,
Electrical Components,
Electrical/Electronic Applications,
Fishing Lines,
Fishing Nets,
Garden Equipment,
Home Appliances,
Lawn Equipment,
Personal Accessories,
Pool Covers,
Sporting Goods,
Tablets,
Tarpaulins,
Turf Applications
Plastics & Elastomers Processing Methods: Injection Molding

Properties

Mechanical Properties
Physical Properties
Thermal Properties
Electrical Properties
Impact Properties
Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.

¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

	Value	Units	Test Method / Conditions
Flexural Modulus ¹¹	18610	MPa	ASTM D790
Tensile Stress (Break, 5 mm/min) ¹¹	196	MPa	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	243	MPa	ISO 527
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	214	MPa	ASTM D638
Tensile Stress (Break) ¹¹	236	MPa	ASTM D638
Flexural Stress ¹¹	393	MPa	ASTM D790
Flexural Stress ¹¹	349	MPa	ISO 178
Tensile Strain (Break, 5 mm/min) ¹¹	2.7	%	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	2.2	%	ISO 527
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	3	%	ASTM D638
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹	326	MPa	ASTM D790
Tensile Modulus (at 1 mm/min) ¹¹	18700	MPa	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	23010	MPa	ISO 527
Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹	325	MPa	ASTM D790
Flexural Stress (Yield, at 2 mm/min) ¹¹	290	MPa	ISO 178
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	16100	MPa	ASTM D790
Flexural Stress (Break, 2 mm/min) ¹¹	280	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	15200	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	18770	MPa	ISO 178

	Value	Units	Test Method / Conditions
Density ¹¹	1.22	g/cm³	ISO 1183
Density ¹¹	1.24	g/cm³	ASTM D792
Mold Shrinkage (flow) ᵍ ¹¹	0.1 - 0.3	%	SABIC method
Water Absorption (at 23°C, 24hrs) ¹¹	0.25	%	ISO 62-1
Specific Gravity ¹¹	1.2	—	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.2	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.1 - 0.3	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.8 - 1	%	ASTM D955
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.3	%	ISO 62

	Value	Units	Test Method / Conditions
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	211	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	217	°C	ASTM D648
Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹	0.0000074	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹	0.000095	1/°C	ISO 11359-2
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80104, sp=64mm) ¹¹	221	°C	ISO 75/Bf
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80104, sp=64mm) ¹¹	2.21E+02	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	213	°C	ISO 75/Af
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	205	°C	ISO 75/Af
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	220	°C	ASTM D648
Coefficient of Thermal Expansion (at -30°C to 30°C, flow) ¹¹	0.000012	1/°C	ASTM D696
Coefficient of Thermal Expansion (at -30°C to 30°C, xflow) ¹¹	0.000055	1/°C	ASTM D696

	Value	Units	Test Method / Conditions
Surface Resistivity ¹¹	10 - 1000	Ω	ASTM D257

Regulatory & Compliance

Packaging & Availability

LNP™ THERMOCOMP™ Compound QC006