LNP THERMOCOMP™ Compound - RB006 - SABIC's Specialty

Identification & Functionality

Features & Benefits

Labeling Claims: No Added PFAS
Materials Features: Cost Effective,
Good Mold Release,
Heat Stabilized,
High Stiffness,
Low Warpage,
No Added PFAS

Applications & Uses

Markets: Building & Construction,
Consumer Goods,
Electrical & Electronics,
Personal Care,
Printing & Packaging
Applications: Consumer Goods — Appliances & Electronics
Building & Construction — Decorative Materials & Finishes
Artificial Turf
Electrical & Electronics — Devices & Assemblies
Consumer Electronics,
Displays
Consumer Goods — Lawn & Garden
Printing & Packaging — Packaging
Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
Applicators & Accessories
Electrical & Electronics — Parts & Components
Connectors,
Switches & Relays
Consumer Goods — Sports & Recreation
Plastics & Elastomers End Uses: Appliances,
Building Materials,
Cell Phones,
Commercial Appliance,
Computer Components,
Consumer Applications,
Containers,
Displays,
Electrical Components,
Electrical/Electronic Applications,
Fishing Lines,
Fishing Nets,
Garden Equipment,
Home Appliances,
Lawn Equipment,
Personal Accessories,
Pool Covers,
Sporting Goods,
Tablets,
Tarpaulins,
Turf Applications
Plastics & Elastomers Processing Methods: Injection Molding

Properties

Flame Rating: UL 94 HB
Mechanical Properties
Physical Properties
Thermal Properties
Electrical Properties
Impact Properties
Injection Molding
Flame Characteristics
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.

¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

	Value	Units	Test Method / Conditions
Tensile Stress (Break, 5 mm/min) ¹¹	56	MPa	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	80	MPa	ISO 527
Tensile Stress (Break) ¹¹	66	MPa	ASTM D638
Tensile Strain (Break, 5 mm/min) ¹¹	9	%	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	7.6	%	ISO 527
Tensile Strain (Break) ¹¹	3	%	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	58	MPa	ASTM D638
Tensile Modulus (at 1 mm/min) ¹¹	4500	MPa	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	7280	MPa	ISO 527
Tensile Modulus (at 50 mm/min) ¹¹	4320	MPa	ASTM D638
Tensile Modulus (at 50 mm/min) ¹¹	6810	MPa	ASTM D638
Flexural Stress (Break, 2 mm/min) ¹¹	130	MPa	ISO 178
Flexural Stress ¹¹	124	MPa	ASTM D790
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	6.5	%	ASTM D638
Flexural Modulus (at 2 mm/min) ¹¹	4400	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	3840	MPa	ISO 178
Flexural Modulus ¹¹	4690	MPa	ASTM D790
Hardness (Rockwell L) ¹¹	105	—	ISO 2039-2
Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹	87	MPa	ASTM D790
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	4050	MPa	ASTM D790

	Value	Units	Test Method / Conditions
Density ¹¹	1.37	g/cm³	ISO 1183
Density ¹¹	1.36	g/cm³	ASTM D792
Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹	1.1 - 1.5	%	SABIC method
Water Absorption (at 23°C, saturated) ¹¹	5.5	%	ISO 62-1
Specific Gravity ¹¹	1.38	—	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.72	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	1 - 3	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	1 - 3	%	ASTM D955
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.72	%	ISO 62

	Value	Units	Test Method / Conditions
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	101	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	92	°C	ASTM D648
Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹	0.00004	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹	0.00004	1/°C	ISO 11359-2
Vicat Softening Temperature (Rate B/120) ¹¹	253	°C	ISO 306
Heat Deflection Temperature/Be (at 0.45MPa, Edgew 120104, sp=100mm) ¹¹	235	°C	ISO 75/Be
Heat Deflection Temperature/Ae (at 1.8 Mpa, Edgew 120104, sp=100mm) ¹¹	100	°C	ISO 75/Ae
Coefficient of Thermal Expansion (at -30°C to 30°C, flow) ¹¹	0.000063	1/°C	ASTM D696
Coefficient of Thermal Expansion (at -30°C to 30°C, xflow) ¹¹	0.000062	1/°C	ASTM D696
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	95	°C	ISO 75/Af

	Value	Units	Test Method / Conditions
Comparative Tracking Index ¹¹	500	V	IEC 60112
Comparative Tracking Index (M) ¹¹	250	V	IEC 60112

	Value	Units	Test Method / Conditions
Izod Impact (Unnotched, at 23°C) ¹¹	320	J/m	ASTM D4812
Izod Impact (Unnotched, at 23°C) ¹¹	390	J/m	ASTM D4812
Izod Impact (Notched, 80104, at 23°C) ¹¹	4	kJ/m²	ISO 180/1A
Izod Impact (Notched, 80104, at 23°C) ¹¹	3	kJ/m²	ISO 180/1A
Izod Impact (Notched, at 23°C) ¹¹	32	J/m	ASTM D256
Izod Impact (Notched, at 23°C) ¹¹	42	J/m	ASTM D256
Izod Impact (Notched, 80104, at -20°C) ¹¹	3	kJ/m²	ISO 180/1A
Izod Impact (Notched, 80104, at -40°C) ¹¹	2	kJ/m²	ISO 180/1A
Charpy Impact (at 23°C, Unnotch Edgew 80104 sp=62mm) ¹¹	30	kJ/m²	ISO 179/1eU
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	25	kJ/m²	ISO 180/1U

	Value	Units	Test Method / Conditions
UL Compliant (94HB Flame Class Rating)	1.6	mm	UL 94 by SABIC-IP
Oxygen Index (LOI)	26	%	ISO 4589

Regulatory & Compliance

Packaging & Availability

LNP™ THERMOCOMP™ Compound RB006