LNP THERMOCOMP™ Compound - RC006 - SABIC's Specialty

Identification & Functionality

Features & Benefits

Labeling Claims: No Added PFAS
Materials Features: Cost Effective,
Electrically Conductive,
High Stiffness,
High Strength,
Light Weight,
No Added PFAS

Applications & Uses

Markets: Building & Construction,
Consumer Goods,
Electrical & Electronics,
Personal Care,
Printing & Packaging
Applications: Consumer Goods — Appliances & Electronics
Building & Construction — Decorative Materials & Finishes
Artificial Turf
Electrical & Electronics — Devices & Assemblies
Consumer Electronics,
Displays
Consumer Goods — Lawn & Garden
Printing & Packaging — Packaging
Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
Applicators & Accessories
Electrical & Electronics — Parts & Components
Connectors,
Switches & Relays
Consumer Goods — Sports & Recreation
Plastics & Elastomers End Uses: Appliances,
Building Materials,
Cell Phones,
Commercial Appliance,
Computer Components,
Consumer Applications,
Containers,
Displays,
Electrical Components,
Electrical/Electronic Applications,
Fishing Lines,
Fishing Nets,
Garden Equipment,
Home Appliances,
Lawn Equipment,
Personal Accessories,
Pool Covers,
Sporting Goods,
Tablets,
Tarpaulins,
Turf Applications
Plastics & Elastomers Processing Methods: Injection Molding

Properties

Flame Rating: UL 94 HB
Mechanical Properties
Physical Properties
Thermal Properties
Electrical Properties
Impact Properties
Injection Molding
Flame Characteristics
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.

¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

	Value	Units	Test Method / Conditions
Tensile Stress (Break) ¹¹	266	MPa	ASTM D638
Tensile Stress (Break) ¹¹	271	MPa	ISO 527
Tensile Stress (Yield, 5 mm/min) ¹¹	261	MPa	ISO 527
Tensile Strain (Break) ¹¹	1.9	%	ISO 527
Tensile Strain (Break) ¹¹	1.7	%	ASTM D638
Tensile Stress (Break, 5 mm/min) ¹¹	250	MPa	ISO 527
Tensile Modulus (at 50 mm/min) ¹¹	27780	MPa	ASTM D638
Tensile Strain (Break, 5 mm/min) ¹¹	2	%	ISO 527
Flexural Stress ¹¹	406	MPa	ASTM D790
Flexural Stress ¹¹	412	MPa	ISO 178
Tensile Modulus (at 1 mm/min) ¹¹	22300	MPa	ISO 527
Flexural Modulus ¹¹	18750	MPa	ASTM D790
Flexural Modulus ¹¹	21020	MPa	ISO 178
Flexural Stress (Yield, at 2 mm/min) ¹¹	360	MPa	ISO 178
Flexural Stress (Break, 2 mm/min) ¹¹	360	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	18900	MPa	ISO 178
Hardness (Rockwell L) ¹¹	108	—	ISO 2039-2

	Value	Units	Test Method / Conditions
Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹	0.1 - 0.3	%	SABIC method
Density ¹¹	1.27	g/cm³	ISO 1183
Density ¹¹	1.28	g/cm³	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.6	%	ASTM D570
Water Absorption (at 23°C, 24hrs) ¹¹	1.1	%	ISO 62-1
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.1	%	ASTM D955
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.08	%	ISO 294
Water Absorption (at 23°C, saturated) ¹¹	4.5	%	ISO 62-1
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.6	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.56	%	ISO 294
Wear Factor Washer ¹¹	20	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.46	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.36	—	ASTM D3702 Modified: Manual

	Value	Units	Test Method / Conditions
Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹	0.000008	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹	0.000086	1/°C	ISO 11359-2
Vicat Softening Temperature (Rate B/120) ¹¹	255	°C	ISO 306
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	261	°C	ASTM D648
Heat Deflection Temperature/Be (at 0.45MPa, Edgew 120104, sp=100mm) ¹¹	260	°C	ISO 75/Be
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000108	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000115	1/°C	ISO 11359-2
Heat Deflection Temperature/Ae (at 1.8 Mpa, Edgew 120104, sp=100mm) ¹¹	257	°C	ISO 75/Ae
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000486	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000486	1/°C	ISO 11359-2
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80104, sp=64mm) ¹¹	261	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	252	°C	ISO 75/Af

	Value	Units	Test Method / Conditions
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	67	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80104, at 23°C) ¹¹	11	kJ/m²	ISO 180/1A
Izod Impact (Notched, 80104, at -20°C) ¹¹	7	kJ/m²	ISO 180/1A
Izod Impact (Unnotched, at 23°C) ¹¹	1014	J/m	ASTM D4812
Izod Impact (Notched, 80104, at -40°C) ¹¹	6	kJ/m²	ISO 180/1A
Izod Impact (Notched, at 23°C) ¹¹	96	J/m	ASTM D256
Charpy Impact (at 23°C, Unnotch Edgew 80104 sp=62mm) ¹¹	70	kJ/m²	ISO 179/1eU
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹	15	J	ASTM D3763
Multi-Axial Impact ¹¹	3	J	ISO 6603

	Value	Units	Test Method / Conditions
UL Compliant (94HB Flame Class Rating)	1.6	mm	UL 94 by SABIC-IP
Oxygen Index (LOI)	27	%	ISO 4589

Regulatory & Compliance

Packaging & Availability

LNP™ THERMOCOMP™ Compound RC006