Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
- Labeling Claims
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Electrical Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
| Value | Units | Test Method / Conditions | |
| Tensile Stress (Yield, Type I, 5 mm/min) ¹¹ | 119 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 119 | MPa | ASTM D638 |
| Tensile Strain (Yield, Type I, 5 mm/min) ¹¹ | 2.7 | % | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 3 | % | ASTM D638 |
| Tensile Modulus (at 5 mm/min) ¹¹ | 9300 | MPa | ASTM D638 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ | 195 | MPa | ASTM D790 |
| Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹ | 189 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 7580 | MPa | ASTM D790 |
| Hardness (Rockwell R) ¹¹ | 118 | — | ISO 2039-2 |
| Hardness (Rockwell R) ¹¹ | 118 | — | ASTM D785 |
| Taber Abrasion (CS-17, 1 kg) ¹¹ | 19 | mg/1000cy | ASTM D1044 |
| Tensile Stress (Yield, 5 mm/min) ¹¹ | 125 | MPa | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 125 | MPa | ISO 527 |
| Tensile Strain (Yield, 5 mm/min) ¹¹ | 2 | % | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 2 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 9300 | MPa | ISO 527 |
| Flexural Stress (Yield, at 2 mm/min) ¹¹ | 195 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 8500 | MPa | ISO 178 |
| Ball Indentation Hardness (H358/30) ¹¹ | 122 | MPa | ISO 2039-1 |
| Value | Units | Test Method / Conditions | |
| Specific Gravity ¹¹ | 1.53 | — | ASTM D792 |
| Specific Volume ¹¹ | 0.65 | cm³/g | ASTM D792 |
| Density ¹¹ | 1.53 | g/cm³ | ASTM D792 |
| Filler Content ¹¹ | 30 | % | ASTM D229 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.06 | % | ASTM D570 |
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹ | 0.3 - 0.7 | % | SABIC method |
| Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹ | 0.3 - 0.7 | % | SABIC method |
| Mold Shrinkage (flow, 1.5-3.2 mm) ᵍ ¹¹ | 0.3 - 0.5 | % | SABIC method |
| Mold Shrinkage (flow, 3.2-4.6 mm) ᵍ ¹¹ | 0.5 - 0.8 | % | SABIC method |
| Mold Shrinkage (on Tensile Bar, xflow) ᵍ ¹¹ | 0.5 - 1 | % | SABIC method |
| Mold Shrinkage (xflow, 3.2 mm) ᵍ ¹¹ | 0.5 - 1 | % | SABIC method |
| Mold Shrinkage (xflow, 1.5-3.2 mm) ᵍ ¹¹ | 0.4 - 0.6 | % | SABIC method |
| Mold Shrinkage (xflow, 3.2-4.6 mm) ᵍ ¹¹ | 0.6 - 0.9 | % | SABIC method |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.08 | % | ISO 62 |
| Melt Flow Rate (at 250°C, 2.16 kg) ¹¹ | 17 | g/10 min | ISO 1133 |
| Melt Volume Rate (at 250°C, 2.16 kg) ¹¹ | 13 | cm³/10 min | ISO 1133 |
| Value | Units | Test Method / Conditions | |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 215 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 215 | °C | ISO 306 |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 220 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 203 | °C | ASTM D648 |
| Heat Deflection Temperature (at 0.45 MPa, 6.4 mm, Unannealed) ¹¹ | 215 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ | 207 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.0000252 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.0000252 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.00012 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.00012 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at 60°C to 138°C, flow) ¹¹ | 0.0000252 | 1/°C | ASTM E831 |
| Thermal Conductivity ¹¹ | 0.19 | W/m-°C | ISO 8302 |
| Ball Pressure Test (at 123°C to 127°C) ¹¹ | Pass | — | IEC 60695-10-2 |
| Vicat Softening Temperature (Rate A/50) ¹¹ | 223 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 215 | °C | ISO 306 |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 217 | °C | ISO 75/Bf |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 204 | °C | ISO 75/Af |
| Relative Temperature Index (Electrical) ᵖ ¹¹ | 140 | °C | UL 746B |
| Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 140 | °C | UL 746B |
| Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 140 | °C | UL 746B |
| Value | Units | Test Method / Conditions | |
| Volume Resistivity ¹¹ | 1.00E+15 | Ω.cm | IEC 60093 |
| Volume Resistivity ¹¹ | min. 3.2E+16 | Ω.cm | ASTM D257 |
| Dielectric Strength (in air, at 3.2mm) ¹¹ | 18.7 | kV/mm | ASTM D149 |
| Dielectric Strength (in oil, at 1.6mm) ¹¹ | 24.8 | kV/mm | ASTM D149 |
| Dielectric Strength (in oil, at 1.6mm) ¹¹ | 24 | kV/mm | IEC 60243-1 |
| Relative Permittivity (100 Hz) ¹¹ | 3.8 | — | ASTM D150 |
| Relative Permittivity (1 MHz) ¹¹ | 3.1 | — | IEC 60250 |
| Relative Permittivity (1 MHz) ¹¹ | 3.7 | — | ASTM D150 |
| Dissipation Factor (at 100 Hz) ¹¹ | 0.002 | — | ASTM D150 |
| Dissipation Factor (at 100 Hz) ¹¹ | 0.001 | — | IEC 60250 |
| Dissipation Factor (at at 1 MHz) ¹¹ | 0.01 | — | IEC 60250 |
| Dissipation Factor (at at 1 MHz) ¹¹ | 0.02 | — | ASTM D150 |
| Surface Resistivity (ROA) ¹¹ | 1.00E+15 | Ω | IEC 60093 |
| Dielectric Strength (shorttime, at 1mm) ¹¹ | 19 | kV/mm | IEC 60243-1 |
| Dielectric Strength (in oil, at 0.8mm) ¹¹ | 28 | kV/mm | IEC 60243-1 |
| Dielectric Strength (in oil, at 3.2mm) ¹¹ | 16 | kV/mm | IEC 60243-1 |
| Dissipation Factor (at 50/60 Hz) ¹¹ | 0.001 | — | IEC 60250 |
| Comparative Tracking Index ¹¹ | 300 | V | IEC 60112 |
| Relative Permittivity (50/60 Hz) ¹¹ | 3.1 | — | IEC 60250 |
| Comparative Tracking Index (UL, PLC) ¹¹ | 0 | PLC Code | UL 746A |
| Hot Wire Ignition (PLC 0) ¹¹ | min. 6 | mm | UL 746A |
| Hot Wire Ignition (PLC 1) ¹¹ | min. 1.5 | mm | UL 746A |
| Hot Wire Ignition (PLC 3) ¹¹ | min. 0.84 | mm | UL 746A |
| Hot Wire Ignition (PLC 4) ¹¹ | min. 0.38 | mm | UL 746A |
| High Ampere Arc Ignition (PLC 1) ¹¹ | min. 1.5 | mm | UL 746A |
| High Ampere Arc Ignition (PLC 2) ¹¹ | min. 0.38 | mm | UL 746A |
| High Voltage Arc Track Rate (PLC) ¹¹ | 1 | PLC Code | UL 746A |
| Arc Resistance (Tungsten, PLC) ¹¹ | 5 | PLC Code | ASTM D495 |
| Value | Units | Test Method / Conditions | |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 801 | J/m | ASTM D4812 |
| Izod Impact (Notched, at 23°C) ¹¹ | 85 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹¹ | 80 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 8 | J | ASTM D3763 |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 45 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at -30°C) ¹¹ | 45 | kJ/m² | ISO 180/1U |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 8 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 7 | kJ/m² | ISO 180/1A |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 5.00E+00 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 5 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 45 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 45 | kJ/m² | ISO 179/1eU |
| Value | Units | Test Method / Conditions | |
| Drying Temperature ⁷ | 120 | °C | — |
| Drying Time ⁷ | 3 - 4 | Hrs | — |
| Drying Time (Cumulative) ⁷ | 12 | Hrs | — |
| Maximum Moisture Content ⁷ | 0.02 | % | — |
| Melt Temperature ⁷ | 250 - 265 | °C | — |
| Nozzle Temperature ⁷ | 245 - 260 | °C | — |
| Front - Zone 3 Temperature ⁷ | 250 - 265 | °C | — |
| Middle - Zone 2 Temperature ⁷ | 245 - 260 | °C | — |
| Rear - Zone 1 Temperature ⁷ | 240 - 255 | °C | — |
| Mold Temperature ⁷ | 65 - 90 | °C | — |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa | — |
| Screw Speed ⁷ | 50 - 80 | rpm | — |
| Shot to Cylinder Size ⁷ | 40 - 80 | % | — |
| Vent Depth ⁷ | 0.025 - 0.038 | mm | — |
| Value | Units | Test Method / Conditions | |
| UL Recognized (94HB Flame Class Rating) ᵖ | min. 0.84 | mm | UL 94 |
| Glow Wire Ignitability Temperature (at 1.0 mm) ᵖ | 775 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (at 1.5 mm) ᵖ | 775 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (at 3.0 mm) ᵖ | 825 | °C | IEC 60695-2-13 |
| Glow Wire Flammability Index (at 1 mm) ᵖ | 750 | °C | IEC 60695-2-12 |
| Glow Wire Flammability Index (at 1.5 mm) ᵖ | 750 | °C | IEC 60695-2-12 |
| Glow Wire Flammability Index (at 3 mm) ᵖ | 800 | °C | IEC 60695-2-12 |
| Oxygen Index (LOI) ᵖ | 19 | % | ASTM D2863 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability