Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Composite Materials Functions
- Technologies
- Product Families
Applications & Uses
- Markets
- Application Method
- Composites Processing Methods
- Applications
- Crystic Gelcoat 80PA White is most suitable for all general molding requirements. It has been designed for application by brush yielding good coverage and flow and leveling properties. For normal moldings, the gelcoat thickness should be controlled to about 0.5 - 0.6mm.
- Crystic Gelcoat 80PA White is not recommended for use in the marine application or corrosion resistance application.
- Formulation Guidelines
The following formulations are recommended for laminating.
Parts by Weight Formulation I Crystic Gelcoat 80PA White 100 Catalyst M or MEKP M-50 1-2 Curing should not be carried out at temperature below 15 ºC and the gelcoat must be allowed to attain workshop temperature before being formulated for use. This gelcoat only requires the addition of catalyst to start the curing reaction. Shortly before use, the correct amount of catalyst should be added and thoroughly stirred into the gel coat.
Properties
- Color
- Resin Properties - Unfilled Casting (Cured)
- Typical Gelcoat Properties (Uncured)
- Note
* Curing Schedule - 24hrs at 20ºC, 3hrs at 80ºC.
† Curing Schedule - 24hrs at 20ºC, 5hrs at 80ºC, 3hrs at 120ºC.- Note
- Cured Properties - Curing Schedule (24hrs at 20ºC, 3hrs at 80ºC)
- Deflection Temperature Under Load - Curing Schedule (24hrs at 20ºC, 5hrs at 80ºC, 3hrs at 120ºC)
Value | Units | Test Method / Conditions | |
Barcol Hardness (Model GYZ 934-1)* | 40 | — | BS 2782 |
Deflection Temperature (under load 1.80 MPa) †* | 75 | ºC | BS 2782 |
Elongation (at break)* | 2 | % | BS 2782 |
Tensile Strength* | 65 | MPa | BS 2782 |
Tensile Modulus* | 3500 | MPa | BS 2782 |
Value | Units | Test Method / Conditions | |
Viscosity (at 25°C, B/F SP2, 20 rpm) | 40 - 50 | Poise | BS 2782 |
C & P Viscosity (at 25°C) | 12 - 20 | Poise | BS 2782 |
Specific Gravity (at 25°C) | 1.1 - 1.3 | — | BS 2782 |
Stability (at 20°C) | 3 | Months | BS 2782 |
Gel Time (at 25°C, using 2% Butanox M50 (or other equivalent catalyst)) | 18 - 22 | Minutes | BS 2782 |
Technical Details & Test Data
- Post Curing
Satisfactory laminates for many applications can be made with Crystic Gelcoat 80PA White by curing at workshop temperature (20°C). However, for optimum properties, laminates must be post-cured before being put into service. The molding should be allowed to cure for 24 hours at 20°C, and then be oven-cured for 3 hours at 80°C.
Packaging & Availability
- Packaging Type
- Packaging
Crystic Gelcoat 80PA White is supplied in 20Kg and 225Kg containers
Storage & Handling
- Storage
Crystic Gelcoat 80PA White should be stored in the dark in suitable, closed containers. It is recommended that the storage temperature should be less than 20°C where practical, but should not exceed 30°C. Ideally, containers should be opened only immediately prior to use.