Products in Fillers, Levellers & Joints: Epoxy & Epoxy Derivatives

BD54750 is a low viscosity polyamine epoxy product. The BD54750 is designed for metals and plastics bonding. This product is ideal for highway and bridge deck repairs, potting, casting, and encapsulation, floor systems, linings of tanks and pipes, and coatings. This product has good chemical, corrosion, and water resistance. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 4 hours with a full cure at room temperature within 48 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

Protective Industrial Polymers PIP 125 ESD WR-GP is a two-component, waterborne, solvent free epoxy resin ground plane coating system designed to develop a uniform, non-tracking conductive ground plane to facilitate a consistent electrostatic discharge. When used in combination with PIP 100 ESD HB or PIP 170 ESD SR it produces lower surface resistance readings to meet the mandated requirements of ignition control applications.

Protective Industrial Polymers PIP 100 ESD HB is a high solids, three-component, high-build epoxy resin system designed to facilitate electrostatic control. PIP 100 ESD HB is supplied with a blended cycloaliphatic amine curing agent that exhibits good UV and chemical resistance. This product produces a durable gloss finish.

Protective Industrial Polymers PIP 1000 Thixo HB is a two-or three component, 100% solids, low odor, epoxy resin coating system. PIP 1000 Thixo is primarily designed to grout PIP epoxy mortar systems. PIP 1000 Thixo exhibits a higher degree of body and thixotropy when compared with PIP 1000 Grout or PIP 1000 Gel. PIP 1000 Thixo may also be used as the binder in combination with decorative quartz and silica sand aggregate for vertical cove applications. PIP 1000 Thixo may be used in combination with 1000ST-B hardener for fine crack filling, or skim coat patching needs. PIP 1000 Thixo is supplied with a choice of curing agents to achieve specific cure rates, chemical resistance requirements, utility and final esthetics.

True-Bond LT™ is formulated for cold temperature applications as low as 0°F. Widely used by food plants for repairing freezer floors while the freezer remains operational. Also great for those outdoor repairs that just can't wait until spring. True-Bond LT™ is concrete filler and bonder that will not separate from concrete. Resurfaces chipped and pitted concrete. Resists wear, corrosives, weather, impact. Bonds cracked curbing, masonry, swimming pools. Waterproof. One application lasts for many years.

True-Bond PS™ concrete filler and bonder will not separate from concrete. Resurfaces chipped and pitted concrete. Resists wear. corrosives, weather. impact. Bonds cracked curbing, masonry, swimming pools. Waterproof. One application lasts for many years. Can be used at any temperature above 34°F. Quickest cure is at 70° F or higher.

DuraPatch EPX is a specially formulated, three-component, l00% solids epoxy patching system for resurfacing and repair of concrete substrates. DuraPatch EPX contains a quartz aggregate blend for heavy duty, industrial floors.

SurePoxy HM Gel is a 100% solids, two component, moisture-insensitive, epoxy resin system. This is a highly thixotropic, multi-purpose gel adhesive for use with concrete, metals such as steel, wood, and other substrates. SurePoxy HM Gel is completely non-shrinking and does not contain any oil extenders.

Protective Industrial Polymers PIP 1000 Thixo CR is a two-or three component, 100% solids, low odor, epoxy resin coating system. PIP 1000 Thixo is primarily designed to grout PIP epoxy mortar systems. PIP 1000 Thixo exhibits a higher degree of body and thixotropy when compared with PIP 1000 Grout or PIP 1000 Gel. PIP 1000 Thixo may also be used as the binder in combination with decorative quartz and silica sand aggregate for vertical cove applications. PIP 1000 Thixo may be used in combination with 1000ST-B hardener for fine crack filling, or skim coat patching needs. PIP 1000 Thixo is supplied with a choice of curing agents to achieve specific cure rates, chemical resistance requirements, utility and final esthetics.

Eco-GPE™ is a two-component, neutral epoxy with a high solids content. Priming at 3 mils (0.08 mm) or build coat at up to 30 mils (0.76 mm) (1/32 inch). Colors are not required.

Precision Epoxy Products SC-15P is a colored system formulated for use in machine shops for leveling a wide variety of applications from table tops to linear rail mounting platforms. The standard color is 'Black' but, it can be pigmented to a color of choice and is excellent for hiding substrate surfaces. It offers unparalleled adhesion to properly prepared steel surfaces without delamination. SC-15P is very durable, chemically resistant and is a poured application with advanced leveling characteristics for extreme accuracy. This version is pigmented to allow for additional de-air additives which makes this system a less technical application than the SC-15N.

Precision Epoxy Products FP-85 is the pigmented version of the FP Series Epoxies for use in surface plate applications. Available in 14 standard colors with custom colors available upon request. Both Floor Plate Epoxies are extremely durable, chemical resistant with excellent scratch and impact resistance.

Duromar® Durofil is a specially formulated 100% solids epoxy grout and rebuilding product for filling holes and rebuilding severely chemically attacked concrete floors and secondary containment areas. Duromar® Durofil provides an excellent base for other DUROFLOR® products, such as CHEMCRETE, DF-4301, etc., where more acid resistance or a smoother finish is required.

KEY #730-FC is a 100% solids fast cure epoxy adhesive/filler with <10 min. working time. KEY #730-FC is used to bond most materials including flooring materials, precast base, divider strip, marble/granite, ceramics, glass, cement board and drywall. KEY #730-FC is durable and impact resistant making it the ideal material for repair of concrete cracks, etc.

Protective Industrial Polymers PIP 1000 Thixo ST is a two-or three component, 100% solids, low odor, epoxy resin coating system. PIP 1000 Thixo is primarily designed to grout PIP epoxy mortar systems. PIP 1000 Thixo exhibits a higher degree of body and thixotropy when compared with PIP 1000 Grout or PIP 1000 Gel. PIP 1000 Thixo may also be used as the binder in combination with decorative quartz and silica sand aggregate for vertical cove applications. PIP 1000 Thixo may be used in combination with 1000ST-B hardener for fine crack filling, or skim coat patching needs. PIP 1000 Thixo is supplied with a choice of curing agents to achieve specific cure rates, chemical resistance requirements, utility and final esthetics.

Precision Epoxy Products FP-80 is a clear self-leveling system for use in surface plate applications. This system is extremely hard and can be used in industrial laminating applications that have harsh or punishing environments.

Eco-MPE™ is a two-component, neutral epoxy with a high solids content. Priming at 3 mils (76.2 microns) or build coat at up to 30 mils (762 microns) (1/32 inch). For thicker applications, a slurry option is available (instructions at the end of the document). Colors are not required.

Chemester® Mortar is an epoxy novolac based vinyl ester resin mortar for chemical resistant brick and tile vessel construction.

True-Bond CT™ is the answer for expansion joints or asphalt surfaces. From hairline cracks to crater-like potholes this product comes through every time. With up to 35% elasticity it is extremely flexible to temperature changes, yet incredibly hard and durable. Serves as an excellent waterproofing membrane for bridges and concrete overlays. Perfect for expansion joints, roof repairs and bridge footings, True-Bond CT™ boasts a minimum tensile elongation of 35%. True-Bond CT™ is asphalt filler and bonder that will not separate from bituminous surfaces. Repairs blacktop and concrete. Resists wear, corrosives, weather, impact. Waterproofing membrane for bridges and concrete overlays Bonds expansion joints and bridge footings. One application lasts for years.

Pennsealer EE-CT is a single component, waterbased, cationic, coal tar epoxy sealer / coating. Specially designed urethane modified epoxy polyelectrolyte emulsion offers unique interactive technology to this compound, which upon cure, produces a tough, durable and protective coating to the treated surface.

True-Bond Gel™ is perfect for repairing cracked walls and even ceilings without the need for forms. Holds up to the same durability standards as all True-Bond™ materials. True-Bond Gel™ is concrete filler and bonder that will not separate from concrete. Resurfaces chipped and pitted concrete. Resists wear, corrosives, weather, impact. Bonds cracked curbing, masonry, swimming pools and is Waterproof. One application lasts for many years.

Fill-Loc™ Crack Repair is a two-component, VOC compliant, 100% epoxy floor patching product. It is designed to make repairs to small vertical and horizontal surface imperfections prior to applying a thin coating. It will quickly fill and span small cracks without slumping. It can also be used to skim coat over small roughed surface areas.

SPARTACOTE® Epoxy Membrane is a flexible epoxy membrane underlayment designed to bridge surface cracks. A high solids, two component epoxy containing flexiblized epoxy resin and silica fillers, it can be used in combination with other SPARTACOTE products to produce a durable, seamless coating system.

KEY #715 is a 100% solids epoxy crack filler used to patch or repair floor and wall surfaces. KEY #715 is the ideal material for repair of concrete surfaces damaged from environmental or chemical attack. KEY #715 can also be used as a base material beneath coating, slurry, and mortar systems to repair defects in the concrete before coating.

EPOXYPLUS is the latest advancement in non-staining technology. Specially formulated with 100% solid epoxy resins and hardeners, EPOXYPLUS uses integrally colored quartz fillers, which eliminates pigment staining of tiles, typical of traditional cement and epoxy grouts and joint filters. It can be used for setting and grouting ceramic tile, pavers, marble and stone over a variety of substrates.

Precision Epoxy Products SC-15N is a clear system formulated for use in machine shops for leveling a wide variety of applications from table tops to linear rail mounting platforms. It offers unparalleled adhesion to properly prepared steel surfaces without delamination. SC-15N is very durable, chemically resistant and is a poured application with advanced leveling characteristics for extreme accuracy. This version is used for laminating surfaces that may need to be visible under the epoxy overlay.

RECKLI Epoxy GF Filler is a pasty, glass fiber reinforced, solvent-free twocomponent epoxy resin with high impact resistance as well as compressive- and flexural strength. It is almost shrinkage-free and insensitive to moisture, thus being applicable on slightly humid surfaces. The addition of further filling material is not recommended.

IntegraSqueeze™ Resin is an impermeable well remediation and well abandonment system which has unique fluid and mechanical properties, making it stronger and more ductile than conventional cement. It can be customized to meet individual well requirements and is easily mixed and pumped with standard cement pumping equipment to minimize operational complexity.

CHEM-POXY GROUT E999 is solvent-free 100% solids, moisture-insensitive three component, ultra-low creep, pumpable, high flow and non-shrink epoxy grout system. It is formulated to be highly flowable for clearances down to 13mm.

SurePoxy HM Class B is a high modulus, 100% solids, two-component, moisture-insensitive, epoxy resin system. It is an all-purpose, very high strength rigid adhesive designed for structural bonding of dry and damp materials free of standing water, and may be used with concrete, metals such as steel, wood, and other substrates. This product is chemically engineered specifically for cold weather work in temperatures as low as 32°F. SurePoxy HM Class B does not contain fillers or non-reactive diluents.

True-Bond Kote™ is utilized for heavy impact, chemically resistant, industrial and commercial flooring. Resists chipping, corrosives, weather, bacteria, and impact. True-Bond Kote™ is also an excellent waterproofing material. True-Bond Kote™ will not separate from concrete. True-Bond 'Kote is utilized for heavy impact, chemically resistant, industrial, and commercial flooring. Resists chipping, corrosives, weather, bacteria, and impact Water- proofs. . One application lasts many years.

SurePoxy HM is a 100% solids, two-component, and moisture-insensitive, epoxy resin system. It is an all purpose, very high strength rigid adhesive designed for structural bonding of dry and damp materials free of standing water. SurePoxy HM may be used with concrete, metals such as steel, wood, and other substrates.

KEY #780 is a 100% solids semi-rigid epoxy joint filler used to protect saw cut joints in concrete slabs or in repair of existing damaged joints. KEY #780 absorbs the impact and shock of heavy loads and steel wheeled traffic, preventing erosion of control joint edges. KEY #780 is available in Regular Cure (RC), Fast Cure (FC), and Super Fast Cure (SFC) formulations.

KEY #783 is a 100% solids, semi-rigid epoxy novolac joint filler used to provide chemical resistant protection for saw-cut joints (contraction/control joints) in concrete slabs or to repair existing damaged joints. KEY #783 absorbs the impact and shock of heavy loads and steel wheeled traffic, preventing erosion of control joint edges.

SurePoxy 110 is a multi purpose, moisture insensitive 100% solids, epoxy resin system.

True-Bond™ is concrete filler and bonder that will not separate from concrete. Resurfaces chipped and pitted concrete. Resists wear, corrosives, weather, impact. Bonds cracked curbing, masonry, swimming pools. Waterproofs. One application lasts for many years.