Products in Oil, Gas & Mining Chemicals: Fracturing Fluids

BTC® 85-RT is a quaternary for formulation into a wide variety of institutional and industrial cleaning applications, including water treatment, gas and oil drilling muds and packer fluids, gas and oil recovery injection water systems, gas and oil fracturing fluid systems, and wood preservation. This biocidal active is associated with a u.S. Epa-registered end-use formulation that meets the criteria for applications against emerging viral pathogens. End-use formulations meeting this criteria may be considered for use as hard surface disinfectants against sars-cov-2, the novel coronavirus that causes the disease covid-19.

Tytan™ AQZ30 serves as a highly effective rheology modifier specifically designed for functionalized guar derivatives, primarily utilized in secondary and tertiary recovery processes for oil and gas wells. This versatile product can crosslink in both water-borne and solvent-borne coatings, providing exceptional adhesion in water-borne and solvent-borne printing inks. Additionally, Tytan™ AQZ30 offers preventive measures against yellowing of the polymer during use.

Tytan™ TAA boasts an exceptional balance between reactivity and cross-linking/adhesion-improvement properties, rendering it highly suitable for significantly enhancing the performance of industrial coatings on challenging modern polymeric substrates, glass, and certain metals. It's important to note that Tytan™ TAA is exclusively applicable in solvent-based inks and coatings.

Alpha Olefin Sulfonate Synsul™ AOS is an aqueous solution of sodium olefin sulfonates with a molecular weight of approximately 325. This non-ionic surfactant is highly effective as the foaming agent in many different personal care applications as well as fracturing fluids for subterranean formations. It also has utility as a foaming agent in enhanced oil recovery and is an efficient component for the clean-up of gas producing wells. Synsul™ AOS exhibits excellent heat stability and is compatible with a wide variety of other additives. It is especially suited for use in freshwater systems and is readily biodegradable.

Encap-HT is an encapsulated oxidizer for use as a delayed release breaker in hydraulic fracturing applications. Encap-HT slowly releases ammonium persulfate breaker into the fracturing fluid, thus enabling a higher concentration of breaker to be used without fluid rheology being compromised.

Encap-LT is an encapsulated oxidizer for use as a delayed release breaker in hydraulic fracturing applications. Encap-LT slowly releases ammonium persulfate breaker into the fracturing fluid, thus enabling a higher concentration of breaker to be used without fluid rheology being compromised.

Encap-HT Xtra is an encapsulated oxidizer for use as a delayed release breaker in hydraulic fracturing applications. Encap- HT slowly releases ammonium persulfate breaker into the fracturing fluid, thus enabling a higher concentration of breaker to be used without fluid rheology being compromised.

Fracsal Ultra crosslinking additive consists of a specifically sized, sparingly-soluble borate crosslinking agent suspended in a aqueous, crosslink modifier solution. The low pour point of the winterized Fracsal Ultra makes this product ideal for use under extreme cold conditions. The standard concentration for Fracsal Ultra is 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1.5 to 6.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal Ultra packaging can be customized to meet specific requirements.

Fracsal Ultra SC crosslinking additive consists of a specifically sized, sparingly-soluble borate crosslinking agent suspended in a aqueous, crosslink modifier solution. The low pour point of the winterized Fracsal Ultra SC makes this product ideal for use under moderately cold conditions. The standard concentration for Fracsal Ultra SC is 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1.5 to 7.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal Ultra SC packaging can be customized to meet specific requirements.

Fracsal Waterbase MP consists of a specifically sized, sparingly-soluble borate crosslinking agent suspended in an aqueous solution. The standard concentration for Fracsal Waterbase MP is 1 to 3 gal per 1,000 gal of fracturing fluid. Crosslink times range from 2 to 6 minutes, depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal Waterbase MP packaging can be customized to meet specific requirements.

Fracsal II crosslinking additive consists of a specifically sized, sparingly-soluble borate crosslinking agent suspended in a hydrocarbon based carrier fluid. A standard concentration for Fracsal II is 1.0 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 3 to 5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system.

Fracsal Waterbase EM is formulated as three separate products, Fracsal Waterbase EM1, Fracsal Waterbase EM2, and Fracsal Waterbase EM3, each product with a different crosslink time. The Fracsal Waterbase EM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous solution. Fracsal Waterbase EM series contains a solubilized alkaline salt modifier which is capable of adjusting the rate at which gelation of organic polymer occurs, without substantially altering the final pH or other characteristics of the crosslinked system. Typical usage concentrations for all Fracsal Waterbase EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1 minute to 3.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system.

Fracsal Waterbase EM is formulated as three separate products, Fracsal Waterbase EM1, Fracsal Waterbase EM2, and Fracsal Waterbase EM3, each product with a different crosslink time. The Fracsal Waterbase EM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous solution. Fracsal Waterbase EM series contains a solubilized alkaline salt modifier which is capable of adjusting the rate at which gelation of organic polymer occurs, without substantially altering the final pH or other characteristics of the crosslinked system. Typical usage concentrations for all Fracsal Waterbase EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1 minute to 3.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system.

Fracsal EM is formulated as three separate products, Fracsal EM1, Fracsal EM2, and Fracsal EM3, each product with a different crosslink time. The Fracsal EM series consists of a specially sized, sparingly-soluble borate crosslinking agent and an alkaline salt modifier suspended in a carrier fluid with an extremely low aromatic content. Typical usage concentrations for all Fracsal EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 2 minutes to 11.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal EM packaging can be customized to meet specific requirements.

Fracsal MS is a concentrated borate solution that is used to crosslink guar and derivatized guar-based fracture fluid systems. Fracsal MS is added continuously during the fracturing fluid pumping operation. Fracsal MS produces a unique gel structure downhole that is elastic and thermally stable. This product exhibits improved sand transport into fractures, and the ability to re-heal itself and form a stable gel structure after shearing.

Fracsal Waterbase EM is formulated as three separate products, Fracsal Waterbase EM1, Fracsal Waterbase EM2, and Fracsal Waterbase EM3, each product with a different crosslink time. The Fracsal Waterbase EM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous solution. Fracsal Waterbase EM series contains a solubilized alkaline salt modifier which is capable of adjusting the rate at which gelation of organic polymer occurs, without substantially altering the final pH or other characteristics of the crosslinked system. Typical usage concentrations for all Fracsal Waterbase EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1 minute to 3.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system.

Fracsal EM is formulated as three separate products, Fracsal EM1, Fracsal EM2, and Fracsal EM3, each product with a different crosslink time. The Fracsal EM series consists of a specially sized, sparingly-soluble borate crosslinking agent and an alkaline salt modifier suspended in a carrier fluid with an extremely low aromatic content. Typical usage concentrations for all Fracsal EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 2 minutes to 11.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal EM packaging can be customized to meet specific requirements.

Rockwater Energy XLZ - 351 is an aqueous zirconium crosslinker of triethanolamino zirconium lactate. XLZ - 351 is an effective crosslinker for low pH CMC fluids, and is ideal for use with guar and guar derivatives across a wide fluid pH and temperature range. Slightly delayed when used in neutral pH fracturing fluids.

APChem OMS is a highly concentrated (70% active) oil-based slurry used to break hydrocarbon gels. Effective temperature range from 4 to 149°C.

Fracsal IV crosslinking additive consists of a specifically sized, sparingly-soluble borate crosslinking agent suspended in a carrier fluid with an extremely low aromatic content. The standard concentration for Fracsal IV is 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 6 to 9.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal IV packaging can be customized to meet specific requirements.

APChem HGA 44 is a organo-metallic complex cross-linker that rapidly releases its metal hydroxide for cross-linking HGA-37 up to 121°C.

Anhui Taichang Chemical Titanate Cross-linking Agent TA-9-2 are used to cross link with sesbania gum, guar gum, carboxymethyl cellulose CMC and etc.

Rockwater Energy XLZ - 350 is an aqueous zirconium crosslinker of diisopropyl bistriethanolamino zirconate. XLZ - 350 has application across a wide range of fluid pH and temperatures. Slightly delayed when used in the crosslinking of neutral pH fracturing fluids.

Fracsal Waterbase HM is formulated as three separate products, Fracsal Waterbase HM1, Fracsal Waterbase HM2, and Fracsal Waterbase HM3, each product with a different crosslink time. The Fracsal Waterbase HM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous solution. Fracsal Waterbase HM series contains a supplemental additive as a scale inhibitor or iron control. Typical usage concentrations for all Fracsal Waterbase HM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1 minute to 3.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal Waterbase HM packaging can be customized to meet specific requirements.

APChem HGA-70 is a concentrated phosphate ester based gelling agent for diesel, kerosene or crude oils stable over 149°C. Most active gelling agent manufactured by Clearwater and is used with HGA-48, HGA-61, HGA-S61, or HGA-65 activators.

Fracsal Waterbase HM is formulated as three separate products, Fracsal Waterbase HM1, Fracsal Waterbase HM2, and Fracsal Waterbase HM3, each product with a different crosslink time. The Fracsal Waterbase HM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous solution. Fracsal Waterbase HM series contains a supplemental additive as a scale inhibitor or iron control. Typical usage concentrations for all Fracsal Waterbase HM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1 minute to 3.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal Waterbase HM packaging can be customized to meet specific requirements.

Anhui Taichang Chemical Titanate Cross-linking Agent TD-5-1are applied to cross link with sesbania gum, guar gum, carboxymethyl cellulose CMC and etc.

APChem HGA 48 is an organo-metallic complex that functions as a cross-linker for hydrocarbon-based fracturing fluids. Temperature range is over 149°C.

Fracsal Waterbase HM is formulated as three separate products, Fracsal Waterbase HM1, Fracsal Waterbase HM2, and Fracsal Waterbase HM3, each product with a different crosslink time. The Fracsal Waterbase HM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous solution. Fracsal Waterbase HM series contains a supplemental additive as a scale inhibitor or iron control. Typical usage concentrations for all Fracsal Waterbase HM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1 minute to 3.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal Waterbase HM packaging can be customized to meet specific requirements.

Fracsal Waterbase crosslinking additive consists of a specifically sized, sparingly-soluble borate crosslinking agent suspended an aqueous, crosslink modifier solution. The standard concentration for Fracsal Waterbase is 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 1 to 8.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system.

Fracsal I crosslinking additive consists of a specifically sized, sparingly-soluble borate crosslinking agent suspended in a hydrocarbon based carrier fluid. A standard concentration for Fracsal I is 1.0 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 2 to 3 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal I packaging can be customized to meet specific requirements.

Fracsal OS is a concentrated borate solution that is used to crosslink guar and derivatized guar-based fracture fluid systems. Fracsal OS is able to achieve low pour points by incorporating a pour point depressant that exhibits low toxicityand has excellent biodegradability. Fracsal OS solutions can achieve pour points as low as -46°C (-15°F). Required pour points for Fracsal OS may be tailored to meet specific customer requirements. This product is added continously during the fracturing fluid pumping operation. Fracsal OS produces a unique gel structure downhole that is elastic and thermally stable. This product exhibits improved sand transport into fractures, and the ability to re-heal itself and form a stable gel structure after shearing.

Fracsal EM is formulated as three separate products, Fracsal EM1, Fracsal EM2, and Fracsal EM3, each product with a different crosslink time. The Fracsal EM series consists of a specially sized, sparingly-soluble borate crosslinking agent and an alkaline salt modifier suspended in a carrier fluid with an extremely low aromatic content. Typical usage concentrations for all Fracsal EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 2 minutes to 11.5 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system. Fracsal EM packaging can be customized to meet specific requirements.

Fracsal Ultra EM is formulated as three separate products, Fracsal Ultra EM1, Fracsal Ultra EM2, and Fracsal Ultra EM3, each product with a different crosslink time. The Fracsal Ultra EM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous crosslink modifier solution. Fracsal Ultra EM series contains a solubilized alkaline salt modifier which is capable of adjusting the rate at which gelation of organic polymer occurs, without substantially altering the final pH or other characteristics of the crosslinked system. Typical usage concentrations for all Fracsal Ultra EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 45 seconds to 3 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system.

Fracsal Ultra EM is formulated as three separate products, Fracsal Ultra EM1, Fracsal Ultra EM2, and Fracsal Ultra EM3, each product with a different crosslink time. The Fracsal Ultra EM series consists of a specially sized, sparingly-soluble borate crosslinking agent suspended in an aqueous crosslink modifier solution. Fracsal Ultra EM series contains a solubilized alkaline salt modifier which is capable of adjusting the rate at which gelation of organic polymer occurs, without substantially altering the final pH or other characteristics of the crosslinked system. Typical usage concentrations for all Fracsal Ultra EM products is from 1 to 3 gal per 1,000 gal of fracturing fluid with crosslink times ranging from 45 seconds to 3 minutes depending upon the pH, temperature, and type of polymer-based fracturing fluid system.

Anhui Taichang Chemical Titanate Cross-linking Agent TA-361 are applied to cross link with sesbania gum, guar gum, carboxymethyl cellulose CMC and etc.