Products

Humiseal UV Curable Adhesives Family are single component, acrylated urethane-based polymers that crosslink to tough and resilient adhesives with exposure to UV light. UV curable adhesives are excellent for high speed or high volume applications where fast or immediate curing is required. In addition, their single-component curing mechanism results in consistent and reliable performance without concerns about mix ratios or generation of heat.

CIM® 1061 is a tough, abrasion, corrosion and chemical resistant, liquid applied coating specifically for use in water and wastewater applications including those which require ANSI/NSF 61 potable water certification. Typical applications for this two component elastomeric urethane coating include tank and reservoir liners, joint seals, tank repairs, and chemical containment.

Humiseal Epoxy Adhesives Family perform in the most challenging environments due to their robust curing mechanism and resulting strength. Epoxies are used in industries including electronics, automotive, and health care devices among others. Humiseal epoxy adhesives are supplied as 2 components, chemical cure systems.

CIM® 1000 Trowel Grade Trowel Grade is a tough, liquid applied, two component, chemical and corrosion resistant urethane elastomeric coating, chemically thickened to allow trowel applications with minimum sag. CIM 1000 Trowel Grade is designed for use with all CIM materials. CIM 1000 Trowel Grade can be used as a crack filler or for application to vertical surfaces and corner flashings. CIM 1000 Trowel Grade offers the same advantages as CIM 1000 and is approved for contact with potable water in accordance with ANSI/NSF 61. CIM 1000 Trowel Grade may be applied at thicknesses up to 250 mils on vertical surfaces in one coat.

Tapecoat® 7100 Wet Bond Epoxy is a two-part 100% solids epoxy.

Vivid Cure™ Uv7041 Is Low Stress, Liquid Optically Clear Adhesive (Loca) Fast Curing, Water White, Urethane Acrylate Designed For Utilization As An Lcd Interface Adhesive. This Product Is A Soft, Flexible, Low Modulus Polymer That Provides A High Amount Of Bond Strength Without Imparting Stress. This Is A Non-Yellowing Adhesive That Exhibits Excellent Resistance To Moisture.

HumiSeal® 1A33 is a single component, polyurethane conformal coating, suitable for general printed circuit board applications. HumiSeal® 1A33 contains no free isocyanates and fluoresces under UV light for inspection purposes. HumiSeal® 1A33 coating is MIL-I-46058C qualified, IPC-CC-830B and RoHS Directive 2011/65/EC compliant and recognized under UL File Number E105698.

HumiSeal® 1A20R is a single component, chemically resistant, fast curing polyurethane conformal coating. HumiSeal® 1A20R fluoresces under UV light for ease of inspection. HumiSeal® 1A20R coating is MIL-I-46058C qualified, IPC-CC-830 and RoHS Directive 2002/95/EC compliant.

CIM® EMT Primer is a two-component solvent-free epoxy primer designed for green and damp porous surfaces such as concrete.

HumiSeal® 1A20 is a single component, chemically resistant, fast curing polyurethane conformal coating. HumiSeal® 1A20 fluoresces under UV light for ease of inspection. HumiSeal® 1A20 coating is MIL-I-46058C qualified, IPC-CC830 and RoHS Directive 2002/95/EC compliant and recognized under UL File Number E105698.

Chase Corporation Roybond 747 is a single component primer for Greenline and Handy Cap.

HumiSeal® 1A27 is a single component, polyurethane conformal coating, suitable for general printed circuit board applications. HumiSeal® 1A27 contains no free isocyanates. HumiSeal® 1A27 coating is RoHS Directive 2002/95/EC compliant and recognized under UL File Number E105698.

CIM® 61TN Epoxy Primer is a two component high solids epoxy coating used as a primer for porous and non-porous surfaces such as concrete and metal. A rapid cure version, CIM 61 TN-RC, is also available and should be used when air and surface temperatures are below 50ºF and above 35ºF during application and cure. CIM 61TN epoxy primer is a two-component, high solids, epoxy coating. It is used as a primer for porous and non-porous surfaces such as concrete and metal.ANSI/NSF 61 approved for potable water contact up to 82ºC.

HumiSeal® 1A27 LTX is a single component, polyurethane conformal coating, suitable for general printed circuit board applications. It is specially formulated with reduced xylene and toluene concentration to be fully compliant with GB30981-2020*. HumiSeal® 1A27 LTX contains no free isocyanates.

Chase Corporation Plasgard 410 Epoxy Coating is a two-part, high-build, solvent-free epoxy coating.

Humiseal Urethane Adhesives Family are designed for demanding bonding requirements in industries including electronics, automotive, and health care devices among others. Polyurethanes are supplied as 2 component, chemical cure systems.

HumiSeal® 1B73 is a single component, fast drying, acrylic conformal coating intended for use on printed circuit assemblies. HumiSeal® 1B73 is also produced as pre-blended products, at a range of viscosities, suitable for a variety of application methods without further dilution. After complete cure, the properties of HumiSeal® 1B73 Pre-blends and HumiSeal® 1B73 are comparable.

CIM® 500 is a tough, durable, waterproofing coating specifically formulated to meet the demands of waterproofing for buried, non-UV exposed, or below grade applications. This two-component, liquid applied urethane coating adheres to most materials to form a permanent, seamless barrier to water. It is especially well suited for plaza decks, areas with multiple penetrations and curbs, and between-slab waterproofing.

HumiSeal® 1B18 is a single component, fast drying, acrylic conformal coating intended for use on printed circuit assemblies. HumiSeal® 1B18 demonstrates excellent flexibility and electrical properties, fluoresces under UV light for ease of inspection and is easily repaired. HumiSeal® 1B18 coating is RoHS Directive 2002/95/EC compliant, and recognized under UL File Number E105698.

Tapecoat® 7030 High-Build Epoxy FS Fast-Set Epoxy is a two-part, 100% solids fast curing epoxy.

CIM® 1000 is a liquid applied urethane coating that cures in hours to form a tough elastomeric coating that adheres to most substrates, forming a chemical and abrasion resistant barrier for waterproofing, corrosion protection, and containment of water and most aqueous chemicals.

Chase Corporation Omniprime is a single component universal primer which can be used with Tapecoat cold or hot applied tapes.

CIM® 800 is a tough, weather durable, waterproofing coating specifically formulated to meet the demands of waterproofing above or below grade. This two component, cold, liquid applied urethane coating adheres to most materials to form a permanent seamless barrier to water. It is especially well suited for roofs over critical spaces (e.g. clean rooms, control rooms), green roofs, plaza decks, areas with multiple penetrations and curbs, and between-slab waterproofing.

HumiSeal® 1R32 LTX is a fast drying, single component acrylic conformal coating, specifically designed to protect against the effects of moisture, corrosive environments and dirt. It is specially formulated with reduced xylene and toluene concentration to be fully compliant with GB30981-2020.

HumiSeal® 1B66 is a fast drying, single component, acrylic conformal coating that provides excellent moisture and environmental protection for printed circuit assemblies. HumiSeal® 1B66 demonstrates outstanding flexibility and is easily repaired. HumiSeal® 1B66 coating is RoHS Directive 2002/95/EC compliant.

Tapecoat® 7000 Epoxy is a two-part high-temperature epoxy.

HumiSeal® 1B15 is a single component, fast drying, easily repaired, acrylic conformal coating intended for use on printed circuit assemblies. HumiSeal® 1B15 coating is RoHS Directive 2002/95/EC compliant.

Tapecoat® 7025 EZ Flow Epoxy is a two-part easy to apply all-purpose epoxy coating.

HumiSeal® Acrylic Gel is a fast drying, single component, thixotropic acrylic paste that provides excellent moisture and environmental protection for printed circuit assemblies. HumiSeal® Acrylic Gel has been designed for use with our acrylic conformal coatings. HumiSeal® Acrylic Gel can be used for sealing, damming and to provide an extra level of protection around component leads. HumiSeal® Acrylic Gel fluoresces under UV light for ease of inspection and is easily repaired. HumiSeal® Acrylic Gel is in full compliance with the RoHS Directive 2002/95/EC.

HumiSeal® 1B31 LTX is a fast drying, single component acrylic conformal coating, specifically designed to protect against the effects of moisture, corrosive environments and dirt. It is specially formulated with reduced xylene and toluene concentration to be fully compliant with GB30981-2020*. Humiseal 1B31 LTX is available in a range of preblends, which are formulated for use with no further dilution.

HumiSeal® 1R32 is a fast drying, single component acrylic conformal coating that provides excellent moisture and environmental protection for printed circuit assemblies. HumiSeal® 1R32 fluoresces under UV light for ease of inspection and is easily repaired. HumiSeal® 1R32 is in full compliance with the RoHS Directive 2002/95/EC.

Chase Corporation Primer B400 is designed to be used with Servi wrap bitumen tapes, except for M30 and Outer wrap.

HumiSeal® 1B31 is a fast drying, single component, acrylic conformal coating that provides excellent moisture and environmental protection for printed circuit assemblies. HumiSeal® 1B31 demonstrates excellent flexibility, fluoresces under UV light for ease of inspection and is easily repaired. HumiSeal® 1B31 coating is MIL-I-46058C qualified, IPC-CC-830 and RoHS Directive 2002/95/EC compliant.