Products

This product is a filled prototype casting compound on polyurethane base and is flame retardant according to UL 94 V-0 and clasification DIN EN 45545-2: 2013-08 class R24 HL2 Processing preferentially in standard vacuum casting plants.

Ebalta MG 453 GF is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Release agent – please see category release agent

This product is a polyurethane system. Mechanical data according to test pieces post-cured for 8 hrs. at 80°C. No heavy chemical and mechanical stress before 7 days after curing at room temperature (20-23°C).

ebalta MG 321 FR is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryllacquer- systems. As release agent you can use our T 03-01. MG 321 FR beige fire behavior according to UL 94, 3 mm thickness V0 With MG 883 the potlife of MG 321 FR beige can be set up to 120 secs. MG 321 FR-S beige/ black - Approved according to UL 94 - File E191776 Vol. 1 fire behavior based on UL 94, 3 mm thickness V0 and 5VA

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

This product is a polyurethane system. Mechanical data according to test pieces post-cured for 8 hrs. at 80°C. No heavy chemical and mechanical stress before 7 days after curing at room temperature (20-23°C).

ebalta MG 425 is processed on a two-component low pressure device. The systems MG 400 / MG 425 / MG 475 are cured with the hardener PUR 19. By mixing MG 425 with MG 400 the E-modulus can variably between 630 – 1550 MPa. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryllacquer- systems. Release agent – please see category release agent

This product is a Polyurethane system If the product is cured at room temperature, no entire chemical and mechanical load before 7 days after curing.

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

SILASTIC™ RTV-3120 are pourable rubber bases that become firm, flexible silicone rubber when cured. There is a choice of three catalysts to select from in order to tailor your working times and cure rates.

This product is a polyurethane system. "VP"-products are experimental products. Regarding technical data slight modifications are possible.

The product is a Polyurethane system. For improving of the flow characteristics, GM 973 can be preheated to approx. 30°C. The final strength is achieved at room temperature after approx. 3-5 days. By post-curing at 80°C for 5 hours the stated values are achieved in short time. Parts / molds must not be cast with addition curing silicone, since this might lead to faulty reactions when curing the silicone.

ebalta MG 426 is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryl-lacquer- systems. Release agent – please see category release agent.

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

ebalta MG 453 is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Release agent – please see category release agent

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.