Products

ebalta AH 120/ TL-1 is a very thin liquid epoxy resin with high values of strength and dimensional stability. Due to its good impregnating and wetting properties it is suitable as laminating resin for high-strength components with fabrics of glass –or carbon fiber. ebalta AH 120/ TL-1 is suitable for laminating of thin as well as thick laminates with large surface up to a thickness of 10 mm. Mechnical properties basing on test pieces being postcured for 8 hrs. at 80°C Demoulding depending on layer thickness, geometry and room temperature. Check for individual case. Postcuring before demoulding of laminates, if possible.

Ebalta AH 100 is a very thin, unfilled epoxy resin, which can be used with different hardeners. Depending on the application the suitable hardener can be mixed with the resin AH 100. This resin/hardener-mixture is inexpensive and therefore suitable as binder for silica sand auxiliary negatives.

Ebalta AH 110 / TGL is an unfilled epoxy resin with high strength values and dimensional stability, even at increased temperature. It can be used as casting resin with powdered fillers as aluminum powder, laminating resin with glass fabric and binder with grainy fillers as aluminum granules. Depending on application the suitable hardener can be mixed with the resin. AH 110/TGL is suitable as laminating resin for big surfaces at a temperature range until 110 °C.

Ebalta AH 110 / TGS is a non-filled epoxy resin with high strength and dimensional stability, even at increasing temperature. It also can be used as casting resin with powder fillers as aluminum powder, as laminating resin with glass fabrics and as binding resin with granular fillers as aluminum granules. Depending on the application if just needs to use a different hardener for the mixture. As laminating resin AH 110 / TGS is suitable for thin high solid laminates.

Ebalta AH 100 is a very thin, unfilled epoxy resin, which can be used with different hardeners. Depending on the application the suitable hardener can be mixed with the resin AH 100. Due to its almost odorless skinfriendly hardener GL this mixture is also suitable as laminating resin. The good wetting properties allow fast laminating and lead to high glass contents of the laminate. This way you get solid and dimensionally stable parts.

Ebalta AH 110 / TG is a High strength general purpose resin.

Ebalta AH 120 / TG is a Laminating resin.

ebalta AH 120/TC 60 is a very thin liquid epoxy resin with high values of strength and dimensional stability. Due to its good impregnating and wetting properties it is suitable as laminating resin for high-strength components with fabrics of glass –or carbon fiber. ebalta AH 120/TC 60 is suitable for laminating of thin as well as thick laminates with large surface up to a thickness of 8 mm. A post-curing should be executed, if possible before demoulding.

ebalta 120/GL is a very low-viscous two-component epoxy resin with high strength values and fast curing. Due to its good soaking and wetting characteristics, this resin/hardener mixture is most suitable for solid parts with fabrics made of glass or carbon fibers. AH 120/GL is suitable as laminating resin for both large area- and thick laminates. Due to its almost odorless and skin-friendly GL hardener it is most suitable as laminating resin. With a mixing ratio of 100:40 you reach an about 15°C higher TG, slightly stiffer laminates as well as better impact resistance. The laminate thickness should not exceed 6-7 mm.

Ebalta AH 100 is a very thin, unfilled epoxy resin, which can be used with different hardeners. Depending on the application the suitable hardener can be mixed with the resin AH 100. The fast hardener TGS is used for thin laminates and small-volume back fillings.

Ebalta AH 100 is a very thin, unfilled epoxy resin, which can be used with different hardeners. Depending on the application the suitable hardener can be mixed with the resin AH 100. AH 100 / TGL is preferentially used for big volume backfillings.

Ebalta AH 120 / TGL is a very thin liquid epoxy resin with high values of strength and dimensional stability. Due to its good impregnating and wetting properties it is suitable as laminating resin for high-strength components with fabrics of glass –or carbon fiber. ebalta AH 120/TGL is suitable for laminating of thin as well as thick laminates with large surface up to a thickness of 8 mm. A post-curing should be executed, if possible before demoulding.

AH 110/GL is an epoxy resin with high strength even on elevated temperatures. It can be used as a casting resin with powdery fillers like aluminum powder, as a laminating resin with fiber glass cloth and as a bonding resin for granular fillers like aluminum granules. Depending on the application you can choose from a variety of hardeners. AH 100/GL is suitable as laminating resin for large area parts and thick laminates. Due to its almost odourles skin friendly hardener GL, this mixture is especially applicable as laminating resin. With a mixing ratio of 100:39 you reach an about 15°C higher TG, slightly stiffer laminates as well as better impact resistance. The laminate thickness should not exceed 6-7 mm.

Ebalta AH 120 / TGS is heat resistant laminating resin.