Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
- Materials Features
Applications & Uses
- Applications
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
- Thermal Properties
- Electrical Properties
- Other Properties
- Mechanical Properties (Die Cutting)
- Mechanical Properties (TPE)
- Rheological Properties
Value | Units | Test Method / Conditions | |
Charpy Impact Strength (at 23°C) | N | kJ/m² | ISO 179/1eU |
Charpy Impact Strength (at -30°C) | N | kJ/m² | ISO 179/1eU |
Charpy Notched Impact Strength (at -30°C) | 5 | kJ/m² | ISO 179/1eA |
Charpy Notched Impact Strength (at 23°C) | N | kJ/m² | ISO 179/1eA |
Izod Notched Impact Strength (-20°C) | N | kJ/m² | ISO 180/1A |
Izod Notched Impact Strength (-30°C) | 5.4 | kJ/m² | ISO 180/1A |
Value | Units | Test Method / Conditions | |
Melting Temperature (at 10°C/min) | 205 | °C | ISO 11357-1/-3 |
Vicat Softening Temperature (at 50°C/h 50N) | 71 | °C | ISO 306 |
Value | Units | Test Method / Conditions | |
Relative Permittivity (100Hz) | 4.2 | — | IEC 62631-2-1 |
Relative Permittivity (1 MHz) | 3.5 | — | IEC 62631-2-1 |
Dissipation Factor (100 Hz) | 180 | E-4 | IEC 62631-2-1 |
Dissipation Factor (1 MHz) | 495 | E-4 | IEC 62631-2-1 |
Volume Resistivity | min. 1E13 | Ohm*m | IEC 62631-3-1 |
Value | Units | Test Method / Conditions | |
Humidity Absorption | 0.11 | % | Sim. to ISO 62 |
Density | 1310 | kg/m³ | ISO 1183 |
Water Absorption in Water (at 23°C, after 24h) | 0.26 | % | ISO 62 |
Value | Units | Test Method / Conditions | |
Stress (at Break, Normal) | 31 | MPa | ISO 527-1/-2 |
Stress (at 5% Strain, Normal) | 9.6 | MPa | ISO 527-1/-2 |
Stress (at 10% Strain, Normal) | 13 | MPa | ISO 527-1/-2 |
Stress (at 50% Strain, Normal) | 16 | MPa | ISO 527-1/-2 |
Stress (at 100% Strain, Normal) | 15 | MPa | ISO 527-1/-2 |
Tear Strength (Normal) | 145 | kN/m | ISO 34-1; Method B |
Tear Strength (Parallel) | 160 | kN/m | ISO 34-1; Method B |
Strain (at Break, Normal) | 590 | % | ISO 527-1/-2 |
Value | Units | Test Method / Conditions | |
Tensile Modulus | 200 | MPa | ISO 527-1/-2 |
Compression Set Under Constant Strain (at 70°C) | 52 | % | ISO 815 |
Stress (at 5% Strain) | 10 | MPa | ISO 527-1/-2 |
Stress (at 10% Strain) | 14 | MPa | ISO 527-1/-2 |
Stress (at 50% Strain) | 18 | MPa | ISO 527-1/-2 |
Stress (at 100% Strain) | 17 | MPa | ISO 527-1/-2 |
Stress (at Break) | 28 | MPa | ISO 527-1/-2 |
Strain (at Break) | min. 300 | % | ISO 527-1/-2 |
Nominal Strain (at Break) | 400 | % | ISO 527-1/-2 |
Hardness (3s) | 57 | Shore D | ISO 868 |
Hardness (15s) | 57 | Shore D | ISO 868 |
Value | Units | Test Method / Conditions | |
Melt Volume Flow Rate (at 230°C, 2.16 kg) | 17 | cm³/10min | ISO 1133 |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Viscosity Shear Rate
- Chemical Resistance Data
Chemical Name Chemical Resistance Acetic acid (10% by mass) at 23°C Resistant Acetone at 23°C Resistant Ammonium hydroxide (10% by mass) at 23°C Limited resistant, tests necessary to verify
ASTM 1 at 23°C Resistant ASTM 3 at 23°C Resistant Brake fluids (DOT 3/4) at 23°C Not resistant Calcium chloride (10% by mass) at 23°C Limited resistant, tests necessary to verify Chloroform at 23°C Not resistant Diethyl ether at 23°C Limited resistant, tests necessary to verify
Ethanol at 23°C Limited resistant, tests necessary to verify
Ethyl Acetate at 23°C Limited resistant, tests necessary to verify
Fuel; Diesel at 85°C Resistant Hydrochloric acid (10% by mass) at 23°C Resistant Hydrogen peroxide (30% by mass) at 23°C Limited resistant, tests necessary to verify
Nitric acid (10% by mass) at 23°C Resistant Phosphoric acid (10% by mass) at 23°C Resistant Sodium hydroxide (10% by mass) at 23°C Resistant Sulfuric acid (30% by mass) at 23°C Resistant Tetrachloroethylene at 23°C Limited resistant, tests necessary to verify
Toluene at 23°C Resistant Transformer oil at 23°C Not resistant Trichloroethylene at 23°C Not resistant Water at 23°C Resistant Zinc chloride (10% by mass) at 23°C Resistant - Stress Strain (TPE)
- Dynamic Tensile Modulus (E) Temperature
Packaging & Availability
- Packaging Type