Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Applications & Uses
- Markets
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Railway Pads Application Data
Details
Arnitel® is a thermoplastic co-polyester with a very high temperature resistance. Arnitel® ECO TPC is a biobased alternative.Benefits
- Arnitel® TPC allows for cost effective solutions since it yields thermoplastic processing advantages over rubber, resulting in faster cycle times in compraison with other TPE's
- Arnitel® TPC allows for reliable solutions due to its high abrasion resistance, excellent load bearing capacity, great fatigue, and environmental resistance and due to a very consistent performance over temperature ranges from -55°C (-67°F) to +150°C (+300°F) and longest lifetime to failure as compared to any other rubber or class of TPE's used in this application
Properties
- Mechanical Properties
- Thermal Properties
- Electrical Properties
- Other Properties
- Mechanical Properties (TPE)
- Rheological Properties
Value | Units | Test Method / Conditions | |
Yield Stress | 17 | MPa | ISO 527-1/-2 |
Yield Strain | 35 | % | ISO 527-1/-2 |
Stress at Break | 31 | MPa | ISO 527-1/-2 |
Charpy Notched Impact Strength (at +23°C) | N | kJ/m² | ISO 179/1eA |
Charpy Notched Impact Strength (at -30°C) | 16 | kJ/m² | ISO 179/1eA |
Izod Notched Impact Strength (at +23°C) | N | kJ/m² | ISO 180/1A |
Izod Notched Impact Strength (at -30°C) | 15 | kJ/m² | ISO 180/1A |
Value | Units | Test Method / Conditions | |
Melting Temperature (10°C/min) | 218 | °C | ISO 11357-1/-3 |
Temperature of Deflection Under Load (0.45 MPa) | 100 | °C | ISO 75-1/-2 |
Vicat Softening Temperature (50°C/h 50N) | 105 | °C | ISO 306 |
Coefficient of Linear Thermal Expansion (parallel) | 1.1 | E-4/°C | ISO 11359-1/-2 |
Coefficient of Linear Thermal Expansion (normal) | 1.1 | E-4/°C | ISO 11359-1/-2 |
Value | Units | Test Method / Conditions | |
Relative Permittivity (1 MHz) | 4 | — | IEC 62631-2-1 |
Dissipation Factor (1 MHz) | 400 | E-4 | IEC 62631-2-1 |
Volume Resistivity | >1E13 | Ohm*m | IEC 62631-3-1 |
Electric Strength | 21 | kV/mm | IEC 60243-1 |
Comparative Tracking Index | 600 | V | IEC 60112 |
Value | Units | Test Method / Conditions | |
Water Absorption | 2.5 | % | Sim. to ISO 62 |
Humidity Absorption | 0.4 | % | Sim. to ISO 62 |
Density | 1240 | kg/m³ | ISO 1183 |
Value | Units | Test Method / Conditions | |
Tensile Modulus | 210 | MPa | ISO 527-1/-2 |
Stress at 5% strain | 9.2 | MPa | ISO 527-1/-2 |
Stress at 10% strain | 13.2 | MPa | ISO 527-1/-2 |
Stress at 50% strain | 16.5 | MPa | ISO 527-1/-2 |
Stress at 100% strain | 17 | MPa | ISO 527-1/-2 |
Stress at Break | 31 | MPa | ISO 527-1/-2 |
Strain at Break | 300 | % | ISO 527-1/-2 |
Nominal Strain at Break | 400 | % | ISO 527-1/-2 |
Tear Strength | 125 | kN/m | ISO 34-1; Method B |
Shore D Hardness (3s) | 53 | — | ISO 868 |
Value | Units | Test Method / Conditions | |
Melt Volume-Flow Rate (at 230 / * °C, 2.16 / * kg) | 15 | cm³/10min | ISO 1133 |
Molding Shrinkage (parallel) | 1.7 | % | Sim. to ISO 294-4 |
Molding Shrinkage (normal) | 1.8 | % | Sim. to ISO 294-4 |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Chemical Resistance
Chemical Type Chemical Name Resistance Other Acetic acid (10% by mass) at 23°C resistant Ketones Acetone at 23°C resistant Other Ammonium hydroxide (10% by mass) at 23°C limited resistant, tests necessary to verify Other ASTM 1 at 23°C resistant Other ASTM 3 at 23°C resistant Other Brake fluids (DOT 3/4) at 23°C not resistant Other Calcium chloride (10% by mass) at 23°C limited resistant, tests necessary to verify Other Chloroform at 23°C not resistant Ethers Diethyl ether at 23°C limited resistant, tests necessary to verify Alcohols Ethanol at 23°C limited resistant, tests necessary to verify Other Ethyl Acetate at 23°C limited resistant, tests necessary to verify Other Fuel; Diesel at 85°C resistant Other Hydrochloric acid (10% by mass) at 23°C resistant Other Hydrogen peroxide (30% by mass) at 23°C limited resistant, tests necessary to verify Other Nitric acid (10% by mass) at 23°C resistant Other Phosphoric acid (10% by mass) at 23°C resistant Other Sodium hydroxide (10% by mass) at 23°C resistant Other Sulfuric acid (30% by mass) at 23°C resistant Other Tetrachloroethylene at 23°C limited resistant, tests necessary to verify Hydrocarbons Toluene at 23°C resistant Other Transformer oil at 23°C not resistant Other Trichloroethylene at 23°C not resistant Other Water at 23°C resistant Other Zinc chloride (10% by mass) at 23°C resistant - Stress-Strain
- Stress-Strain (TPE)
Packaging & Availability
- Packaging Type