Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Polymer Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Value | Units | Test Method / Conditions | |
Flexural Modulus (at 2.6 mm/min, 100 mm span) ¹¹ | 2732 | MPa | ASTM D790 |
Flexural Stress (Yield, 2.6 mm/min, 100 mm span) ¹¹ | 88 | MPa | ASTM D790 |
Value | Units | Test Method / Conditions | |
Melt Flow Rate (at 300°C, 1.2 kgf) ¹¹ | 9.6 | g/10 min | ASTM D1238 |
Value | Units | Test Method / Conditions | |
Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ | 133 | °C | ASTM D648 |
Relative Temperature Index (Electrical) ᵖ ¹¹ | 80 | °C | UL 746B |
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 80 | °C | UL 746B |
Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 80 | °C | UL 746B |
Value | Units | Test Method / Conditions | |
Ash Content ¹¹ | 19 | Wt. % | - |
Value | Units | Test Method / Conditions | |
Back Pressure ⁷ | 0.3 - 0.7 | MPa | — |
Drying Temperature ⁷ | 120 | °C | — |
Drying Time ⁷ | 3 - 4 | Hrs | — |
Front - Zone 3 Temperature ⁷ | 290 - 310 | °C | — |
Melt Temperature ⁷ | 290 - 310 | °C | — |
Middle - Zone 2 Temperature ⁷ | 275 - 300 | °C | — |
Mold Temperature ⁷ | 70 - 95 | °C | — |
Nozzle Temperature ⁷ | 280 - 305 | °C | — |
Rear - Zone 1 Temperature ⁷ | 265 - 290 | °C | — |
Screw Speed ⁷ | 40 - 70 | rpm | — |
Value | Units | Test Method / Conditions | |
UL Recognized (94V-0 Flame Class Rating) ᵖ | min. 3 | mm | UL 94 |
UL Recognized (94V-1 Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Regional Availability