Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Value | Units | Test Method / Conditions | |
Tensile Stress (Break) ¹¹ | 185 | MPa | ASTM D638 |
Tensile Strain (Break) ¹¹ | 3.3 | % | ASTM D638 |
Flexural Stress ¹¹ | 262 | MPa | ISO 178 |
Flexural Stress ¹¹ | 275 | MPa | ASTM D790 |
Value | Units | Test Method / Conditions | |
Density ¹¹ | 1.46 | g/cm³ | ASTM D792 |
Wear Factor Washer ¹¹ | 6 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
Dynamic COF ¹¹ | 0.61 | — | ASTM D3702 Modified: Manual |
Value | Units | Test Method / Conditions | |
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.00003 | 1/°C | ASTM E831 |
Relative Temperature Index (Electrical) ᵖ ¹¹ | 65 | °C | UL 746B |
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 65 | °C | UL 746B |
Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 65 | °C | UL 746B |
Value | Units | Test Method / Conditions | |
Multi-Axial Impact ¹¹ | 4 | J | ISO 6603 |
Value | Units | Test Method / Conditions | |
Drying Temperature ⁷ | 80 | °C | — |
Drying Time ⁷ | 4 | Hrs | — |
Maximum Moisture Content ⁷ | 0.15 - 0.25 | % | — |
Melt Temperature ⁷ | 280 - 305 | °C | — |
Front - Zone 3 Temperature ⁷ | 295 - 305 | °C | — |
Middle - Zone 2 Temperature ⁷ | 280 - 295 | °C | — |
Rear - Zone 1 Temperature ⁷ | 265 - 275 | °C | — |
Mold Temperature ⁷ | 95 - 110 | °C | — |
Back Pressure ⁷ | 0.2 - 0.3 | MPa | — |
Screw Speed ⁷ | 30 - 60 | rpm | — |
Value | Units | Test Method / Conditions | |
UL Recognized (94HB Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Regional Availability