Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Electrical Properties
- Impact Properties
- Injection Molding
- Note
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Value | Units | Test Method / Conditions | |
Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 14000 | MPa | ASTM D638 |
Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 2.2 | % | ASTM D638 |
Tensile Modulus (at 5 mm/min) ¹¹ | 152 | MPa | ASTM D638 |
Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ | 214 | MPa | ASTM D790 |
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 1.25E+04 | MPa | ASTM D790 |
Value | Units | Test Method / Conditions | |
Density ¹¹ | 1.38 | g/cm³ | ISO 1183 |
Value | Units | Test Method / Conditions | |
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 143 | °C | ISO 75/Bf |
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 137 | °C | ISO 75/Af |
Value | Units | Test Method / Conditions | |
Surface Resistivity ¹¹ | 100 - 10000 | Ω | ASTM D257 |
Value | Units | Test Method / Conditions | |
Izod Impact (Unnotched, at 23°C) ¹¹ | 410 | J/m | ASTM D4812 |
Izod Impact (Notched, at 23°C) ¹¹ | 86 | J/m | ASTM D256 |
Value | Units | Test Method / Conditions | |
Back Pressure ⁷ | 0.2 - 0.3 | MPa | — |
Drying Temperature ⁷ | 120 | °C | — |
Drying Time ⁷ | 4 | Hrs | — |
Front - Zone 3 Temperature ⁷ | 320 - 330 | °C | — |
Maximum Moisture Content ⁷ | 0.02 | % | — |
Melt Temperature ⁷ | 305 - 325 | °C | — |
Middle - Zone 2 Temperature ⁷ | 310 - 320 | °C | — |
Mold Temperature ⁷ | 80 - 110 | °C | — |
Rear - Zone 1 Temperature ⁷ | 295 - 305 | °C | — |
Screw Speed ⁷ | 30 - 60 | rpm | — |
Packaging & Availability
- Country Availability
- Regional Availability