Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Physical Properties
- Mechanical Properties
- Thermal Properties
- Electrical Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Value | Units | Test Method / Conditions | |
Mold Shrinkage (flow) ᵍ ¹¹ | 0.3 | % | SABIC method |
Mold Shrinkage (xflow) ᵍ ¹¹ | 0.5 | % | SABIC method |
Specific Gravity ¹¹ | 1.45 | — | ASTM D792 |
Water Absorption (at 23°C, 24hrs) ¹¹ | 0.05 | % | ISO 62-1 |
Value | Units | Test Method / Conditions | |
Tensile Modulus (at 5 mm/min) ¹¹ | 9500 | MPa | ASTM D638 |
Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 104 | MPa | ASTM D638 |
Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 1.6 | % | ASTM D638 |
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 8500 | MPa | ASTM D790 |
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ | 150 | MPa | ASTM D790 |
Value | Units | Test Method / Conditions | |
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm) ¹¹ | 276 | °C | ASTM D648 |
Heat Deflection Temperature (at 1.82 MPa, 3.2 mm) ¹¹ | 255 | °C | ASTM D648 |
Relative Temperature Index (Electrical) ᵖ ¹¹ | 65 | °C | UL 746B |
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 65 | °C | UL 746B |
Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 65 | °C | UL 746B |
Value | Units | Test Method / Conditions | |
Dielectric Constant (at 1.1 GHz) ¹¹ | 3.56 | — | SABIC method |
Dissipation Factor (at 1.1 GHz) ¹¹ | 0.009 | — | SABIC method |
Value | Units | Test Method / Conditions | |
Izod Impact (Notched, at 23°C) ¹¹ | 34 | J/m | ASTM D256 |
Izod Impact (Unnotched, at 23°C) ¹¹ | 300 | J/m | ASTM D4812 |
Value | Units | Test Method / Conditions | |
Drying Temperature ⁷ | 120 | °C | — |
Drying Time ⁷ | 4 - 7 | Hrs | — |
Front - Zone 3 Temperature ⁷ | 300 - 320 | °C | — |
Melt Temperature ⁷ | 290 - 330 | °C | — |
Middle - Zone 2 Temperature ⁷ | 280 - 300 | °C | — |
Mold Temperature ⁷ | 120 - 150 | °C | — |
Nozzle Temperature ⁷ | 300 - 320 | °C | — |
Rear - Zone 1 Temperature ⁷ | 260 - 280 | °C | — |
Value | Units | Test Method / Conditions | |
UL Recognized (94V-0 Flame Class Rating) ᵖ | min. 0.4 | mm | UL 94 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability