Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
- Product Attributes
NORYL NHP5054 resin is a 20% glass reinforced blend of polyphenylene ether (PPE) and high impact polystyrene (HIPS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of VO at 0.75 mm for thin-wall molding capability. NORYL NHP5054 resin is based on a unique copolymer technology and exhibits good dimensional stability, high heat resistance, strong electrical performance, and very low specific gravity. Itis an excellent candidate for electric vehicle module and battery housings, automotive under-the-hood enclosures and components where thin-wall FR, modulus retention, and high heat resistance is required.
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Physical Properties
- Mechanical Properties
- Thermal Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹³ This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions. UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.
- ¹⁵ Typical values only. Variations within normal tolerances are possible for various colors. All values are measured at least after 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume rate are measured on injection molded samples. All samples are prepared according to ISO 294. Only typical data for material selection purpose.Not to be used for part or tool design. The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
| Value | Units | Test Method / Conditions | |
| Specific Gravity ¹⁵ | 1.3 | — | ASTM D792 |
| Melt Flow Rate (at 250°C, 10.0 kgf) ¹⁵ | 8 | g/10 min | ASTM D1238 |
| Melt Volume Rate (at 280°C, 10.0 kg) ¹⁵ | 22 | cm³/10 min | ISO 1133 |
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹⁵ | 0.27 | % | SABIC method |
| Density ¹⁵ | 1.27 | g/cm³ | ISO 1183 |
| Moisture Absorption (at 23°C, 50% RH) ¹⁵ | 0.24 | % | ISO 62 |
| Mold Shrinkage (flow) ᵍ ¹⁵ | 0.22 | % | SABIC method |
| Mold Shrinkage (xflow) ᵍ ¹⁵ | 0.52 | % | SABIC method |
| Value | Units | Test Method / Conditions | |
| Tensile Strain (Break, Type I, 5 mm/min) ¹⁵ | 2.5 | % | ASTM D638 |
| Tensile Stress (Yield, Type I, 5 mm/min) ¹⁵ | 120 | MPa | ASTM D638 |
| Flexural Modulus (at 2.6 mm/min, 100 mm span) ¹⁵ | 6000 | MPa | ASTM D790 |
| Flexural Stress (Yield, 2.6 mm/min, 100 mm span) ¹⁵ | 150 | MPa | ASTM D790 |
| Tensile Strain (Break, 5 mm/min) ¹⁵ | 2.4 | % | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹⁵ | 110 | MPa | ISO 527 |
| Flexural Modulus (at 2 mm/min) ¹⁵ | 6000 | MPa | ISO 178 |
| Flexural Stress (Yield, at 2 mm/min) ¹⁵ | 145 | MPa | ISO 178 |
| Tensile Modulus (at 1 mm/min) ¹⁵ | 7300 | MPa | ISO 527 |
| Ball Indentation Hardness (H358/30) ¹⁵ | 215 | MPa | ISO 2039-1 |
| Value | Units | Test Method / Conditions | |
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹⁵ | 120 | °C | ASTM D648 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹⁵ | 115 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹⁵ | 122 | °C | ISO 75/Bf |
| Relative Temperature Index (Electrical) ᵖ ¹⁵ | 125 | °C | UL 746B |
| Vicat Softening Temperature (Rate B/120) ¹⁵ | 130 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹⁵ | 128 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹⁵ | 0.000021 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹⁵ | 0.000057 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹⁵ | 0.000032 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, xflow) ¹⁵ | 0.000103 | 1/°C | ISO 11359-2 |
| Relative Temperature Index (Mechanical with impact) ᵖ ¹⁵ | 115 | °C | UL 746B |
| Relative Temperature Index (Mechanical without impact) ᵖ ¹⁵ | 125 | °C | UL 746B |
| Value | Units | Test Method / Conditions | |
| Izod Impact (Notched, at 23°C) ¹⁵ | 100 | J/m | ASTM D256 |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*4 sp=62mm) ¹⁵ | 36 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹⁵ | 8 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹⁵ | 35 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹⁵ | 9 | kJ/m² | ISO 179/1eA |
| Value | Units | Test Method / Conditions | |
| Drying Temperature ⁷ | 105 - 110 | °C | — |
| Drying Time ⁷ | 3 - 4 | Hrs | — |
| Drying Time (Cumulative) ⁷ | 8 | Hrs | — |
| Maximum Moisture Content ⁷ | 0.02 | % | — |
| Melt Temperature ⁷ | 280 - 310 | °C | — |
| Nozzle Temperature ⁷ | 280 - 310 | °C | — |
| Front - Zone 3 Temperature ⁷ | 270 - 310 | °C | — |
| Middle - Zone 2 Temperature ⁷ | 260 - 305 | °C | — |
| Rear - Zone 1 Temperature ⁷ | 250 - 300 | °C | — |
| Mold Temperature ⁷ | 75 - 105 | °C | — |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa | — |
| Screw Speed ⁷ | 20 - 100 | rpm | — |
| Shot to Cylinder Size ⁷ | 30 - 70 | % | — |
| Value | Units | Test Method / Conditions | |
| UL Recognized (94V-0 Flame Class Rating) ¹³ | min. 0.75 | mm | UL 94 |
| Glow Wire Flammability Index (at 3 mm) ¹³ | 960 | °C | IEC 60695-2-12 |
| Glow Wire Ignitability Temperature (at 1.0 mm) ¹³ | 775 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (at 2.0 mm) ¹³ | 800 | °C | IEC 60695-2-13 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability