Products in Base Chemicals & Intermediates: Aluminum Compounds

BCI A is used in ferro alloys/ foundry / chemical.

DiTech Coagulant is widely accepted as the preferred polyaluminum chloride for cost-effective improvement of finished water quality. As a coagulant, it enhances filter performance, potentially eliminates the need for pH adjustment with alkalis, and decreases sludge residuals. It meets the specifications of American Water Works Association Standard B408-18 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dosage of 250 mg/L.

AEROXIDE® Alu C is a fine-particulate, pure aluminum oxide (Al₂O₃) with high specific surface area and marked aggregate and agglomerate structure. Because of it high purity and low water content, the product can be used well as an additive to anorganic materials, for heat insulation, and also as a catalyst substrate. The positive surface charge can be used to control the electrostatic charge.

USALCO Aluminum Chloride is a solution that is very effective in drinking water treatment, removal of phosphorus from municipal/industrial wastewater, and as an intermediate chemical in the manufacturing of various products. This product complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects at a maximum dosage of 250 mg/L.

USALCO Sodium Aluminate Solution (38%) is an economical source of highly reactive alumina manufactured by dissolving alumina tri‐hydrate (ATH) into sodium hydroxide and water. USALCO 38 is also stabilized to prevent alumina from precipitating. The use of only stringently selected raw materials and state‐of‐the‐art manufacturing practices ensures that USALCO 38 is of the highest quality. USALCO 38 meets the specifications of the American Water Works Association Standard B405‐16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals ‐Health Effects at a maximum dosage of 105 mg/L.

DelPAC® 1842 is an advanced formulation of basic polyaluminum chloride that has demonstrated exceptional effectiveness in the treatment of drinking water and the elimination of phosphorus in municipal and industrial wastewater systems. It conforms to the specifications outlined in the American Water Works Association Standard B408-18 and meets the criteria established in NSF/ANSI 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dose of 250 mg/L.

USALCO Sodium Aluminate Solution (45%) is an economical source of highly reactive alumina manufactured by dissolving alumina tri‐hydrate (ATH) into sodium hydroxide and water. USALCO 45 is also stabilized to prevent alumina from precipitating. The use of only stringently selected raw materials and state‐of‐the‐art manufacturing practices ensures that USALCO 45 is of the highest quality. USALCO 45 meets the specifications of the American Water Works Association Standard B405‐16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals ‐Health Effects at a maximum dosage of 89 mg/L.

USALCO Dry Aluminum Sulfate (Rice Grind) is manufactured using state-of-the-art processes and high-quality raw materials to ensure that the product meets the highest quality standards. USALCO offers various grades of dry alum, including low-iron, iron-free, and FCC grades, as well as specialty granular sizes to meet a wide range of applications. This product is used in water treatment, dye production, leather tanning, and papermaking, among other industrial applications. It meets the specifications of the American Water Works Association Standard B403-16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 150 mg/L.

DelPAC® 2450 is a widely accepted polyaluminum chloride solution that is known for its cost-effective benefits in improving water quality. As a coagulant, it can provide longer filtration runs, minimize the need for pH adjustment with alkali, and decrease the amount of sludge residuals. This product meets the standards set by the American Water Works Association Standard B408-18 and complies with NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects at a maximum dosage of 250 mg/L.

DelPAC® 2000 is a widely accepted polyaluminum chloride that is known for its cost-effective ability to improve finished water quality. As a coagulant, it can offer longer filtration runs, minimize or eliminate the need for pH adjustment with alkalis, and reduce sludge residuals. It complies with American Water Works Association Standard B408-18 and NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 250 mg/L.

USALCO Dry Aluminum Sulfate (Purified Grade) is manufactured to meet high-quality standards using advanced processes and premium raw materials. It comes in various grades, including low-iron, iron-free, and FCC grades, and in special granular sizes to meet diverse needs. It is utilized in industries such as water treatment, dye production, leather tanning, papermaking, and others. This dry alum meets the American Water Works Association Standard B403-16 and follows NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 150 mg/L.

USALCO Sodium Aluminate (Granular) is a white powder that easily dissolves in water and is the dry form of sodium aluminate. It is produced by mixing alumina trihydrate with sodium hydroxide to create a solution, which is then solidified by removing excess moisture. This product does not contain any stabilizing agents.

USALCO Dry Aluminum Sulfate (Iron Free Grade) is manufactured using a state-of-the-art process and high-quality raw materials, which ensures that the product meets the highest quality standards. USALCO also produces dry alum in various other grades (low-iron and FCC-grade) and in specialty granular sizes to satisfy even the most difficult applications. USALCO's dry alum is used in water treatment, colors and dyes, leather tanning, papermaking, and many other industrial applications. It meets the specifications of the American Water Works Association Standard B403-16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects at a maximum dosage of 150 mg/L.

USALCO Aluminum Sulfate Solution (Acidified) is produced by dissolving alumina trihydrate in water and sulfuric acid. Only the finest raw materials and advanced manufacturing techniques are used to ensure the top-notch quality of this product. It conforms to the specifications outlined in the American Water Works Association Standard B403-16 and satisfies the criteria set forth in NSF/ANSI 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dose of 150 mg/L.

DelPAC® 2950 is widely accepted as the preferred polyaluminum chloride for cost-effective improvement of finished water quality. As a coagulant, it enhances filter performance, potentially eliminates the need for pH adjustment with alkalis, and decreases sludge residuals. It meets the specifications of American Water Works Association Standard B408-18 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dosage of 250 mg/L.

DelPAC® 1525 is an advanced formulation of basic polyaluminum chloride that has demonstrated exceptional effectiveness in the treatment of drinking water and the elimination of phosphorus in municipal and industrial wastewater systems. It conforms to the specifications outlined in the American Water Works Association Standard B408-18 and meets the criteria established in NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dose of 250 mg/L.

DelPAC® 2020 is a highly effective polyaluminum chloride solution for improving the quality of finished water. As a coagulant, it can offer longer filtration runs, minimize or eliminate the need for pH adjustment with alkalis, and decrease sludge residuals. This product adheres to the standards set by the American Water Works Association Standard B408-18 and meets the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 250 mg/L.

DelPAC® 2500 is a highly regarded polyaluminum chloride solution that is known for its cost-effectiveness in enhancing the quality of finished water. As a coagulant, it can extend filtration runs, minimize or eliminate the requirement for alkali pH adjustment, and decrease sludge residuals. It conforms to the American Water Works Association Standard B408-18 and NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 250 mg/L.

DelPAC® XG (Aluminum Chlorohydrate) is a highly effective coagulant that is used in water and wastewater treatment. DelPAC® XG is proven to be an excellent option for removing organic matter, TSS, and copper. It is known for its high concentration and basicity, making it effective in removing organic matter and performing well over a wide pH range. This product meets the standards set by the American Water Works Association Standard B408-18 and complies with the health effects requirements of NSF/ANSI/CAN 60, with a maximum recommended dosage of 250 mg/L.

USALCO Aluminum Sulfate Solution is manufactured by dissolving alumina trihydrate (ATH) in water and sulfuric acid. To ensure the highest quality of this product, stringently selected raw materials and state-of-the-art manufacturing practices are used. USALCO Alum meets the specifications of the American Water Works Association Standard B403‐16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals ‐ Health Effects at a maximum dosage of 150 mg/L.

USALCO Dry Aluminum Sulfate (Low Iron Grade) is produced using advanced techniques and high-quality materials to meet the highest quality standards. USALCO also produces dry alum in various other grades (iron-free and FCC-grade) and custom granular sizes to meet a wide range of applications. This product is used in water treatment, dye production, leather tanning, papermaking, and other industrial applications. It adheres to the American Water Works Association Standard B403-16 and meets the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dosage limit of 150 mg/L.

Gelest ALUMINUM ISOPROPOXIDE (AKA070) is a reagent used for the reduction of carbonyls to alcohols. It reacts with higher glycols in the non-hydrolytic method to yield ceramics. It also functions as an antioxidant and is commonly used in chemical production.

Gelest ALUMINUM s-BUTOXIDE (AKA020) is employed in the preparation of alumina sols and cordierite ceramics. It is used as a primer for adhesives on mild steel and in catalyst manufacturing and chemical production.

Boratherm™ GA6 S21.5 is submicron ground alumina produced by the calcination of carefully selected synthetic aluminum hydroxide (ATH). Boratherm™ GA grades are often used in combination with Boratherm™ SA and Boratherm™ SG grades in order to enhance a formulation’s particle packing and flow properties, resulting in improved thermal conductivity and stability (filler settling). Boratherm™ GA6 S21.5 is the surface-modified (1.5 % w/w coated) version of Boratherm™ GA6, a submicron ground alumina tailored to improve the stability of thermally conductive uncured polymeric composites. Changes in type of treatment and loading level are possible to meet your specific requirements. To guarantee a consistent product quality for the Boratherm™ GA grades, the chemical composition of the raw materials, the product particle size of the final products, and the treatment process (in the case of the Boratherm™ GA6 S21.5) are closely monitored and kept within a narrow variation.

Boratherm™ SA 0080 spherical alumina particles are made from a special fusion process using high-quality ground alumina material. Boratherm™ SA grades are used in various applications because of their high thermal conductivity, heat resistance, and low thermal expansion. Due to the sphericity of the particles and the possibility to combine grades, one can obtain very high packing densities, resulting in formulations with excellent thermal conduction while maintaining low viscosity and easy application.

Boratherm™ SA 0700 spherical alumina particles are made from a special fusion process using high-quality ground alumina material. Boratherm™ SA grades are used in various applications because of their high thermal conductivity, heat resistance, and low thermal expansion. Due to the sphericity of the particles and the possibility to combine grades, one can obtain very high packing densities, resulting in formulations with excellent thermal conduction while maintaining low viscosity and easy application.

Boratherm™ SA 0050 spherical alumina particles are made from a special fusion process using high-quality ground alumina material. Boratherm™ SA grades are used in various applications because of their high thermal conductivity, heat resistance, and low thermal expansion. Due to the sphericity of the particles and the possibility to combine grades, one can obtain very high packing densities, resulting in formulations with excellent thermal conduction while maintaining low viscosity and easy application.

Boratherm™ SG200 E is produced from carefully selected synthetic aluminum hydroxide (ATH). Boratherm™ SG-E grades are used in various applications because of their high thermal conductivity, flame retardancy, smoke suppression, and low viscosity. Combining these grades with finer products (ATH or Al2O3-based) makes it possible to obtain a high packing density, resulting in excellent thermal conductivity. Boratherm™ SG is perfectly suited for formulations needing good flowability. It is specially designed to offer an ultra-low surface area and large particle sizes.

APYRAL® 40CD stands as a Mineral flame retardant, offering several advantages such as smooth conveyance and dosing, finely textured particles, minimal oil absorption, high extrusion speeds, and outstanding mechanical properties. Its applications span cables, the electrical and electronics industries, construction, and transportation sectors.

PolyJet® 505 is a remarkable flame retardant solution with a base chemical function. Its key component, Alumina Trihydrate (ATH), is an aluminum compound that imparts exceptional fire-resistant properties. Available in powder form, Complying with various chemical inventories like DSL (Canada), IECSC (China), KECI (Korea), NZIoC (New Zealand), PICCS (Philippines), and TSCA (USA), PolyJet® 505 is a versatile choice for enhancing fire safety in diverse applications.

AllanChem Aluminum Sulfate is an inorganic substance commonly used in chemical manufacturing.

AllanChem Aluminum Nitrate 9H2O is an inorganic, colorless, crystalline substance commonly used in chemical manufacturing.

description here.