Products

NM Gelcoat 275 is a thixotropic, pigmented solvent free epoxy gelcoat for laminates. NM Gelcoat 275 can be used for molds and tools.

NM Resin 094 together with NM Hardener 093 C is a low viscosity epoxy resin for manufacturing of sand molds and laminates. The resin can be accelerated with up to 10% of NM Accelerator 254. At increased amounts of accelerator, potlife and exotermic are affected. When having large molds, the accelerator should not be added.

NM Laminering 650 is a two pack, solvent‐free, epoxy laminating system with a high TG and very high strength values. Wetting and adhesive properties are very good to all kind of fibers.

NM ME 585 is a low viscosity, room temperature curing solvent free epoxy resin with all-round properties, i.e. modeling and production of molds.

NM Gelcoat 095C with NM Hardener 101 is a metal powder filled epoxy resin with a low coefficient offriction. NM Gelcoat 095C is designed as a surface resin for molds where there are high demands on durability and lack of pores.

NM Infusion 693 is an extremely low viscosity two pack epoxy system, suitable for infusion processes with demands on high TG. NM Infusion 693 has a very low vapor pressure and can be considered as odorless. Vacuum causes no gas bubbles.

NM Gelcoat 230 is a white solvent free epoxy system designed for surface coats on molds.

NM Infusion 664 is an extremely low viscosity epoxy system, suitable for all kind of infusion processes. The system is based on the latest development within the epoxy technology, which means that the low viscosity can be combined with a high Tg (glass transition temperature) even at room temperature curing. Wetting and adhesive properties are very good to all kind of fibers.

NM Laminating 380 A is a very low viscosity epoxy resin specially designed for good wetting and adhesion to glass-carbon-polyester- and aramide fibers. NM Laminating 380 A shall gel at room temperature or just above. Full cure at 60°C, 24 hours.The low viscosity makes NM Laminating 380 A suitable for injection.

NM Gjutharts 347 is a solvent-free elastic epoxy for potting components exposed to extreme temperature variations. NM Gjutharts 347 is available with two different curing agents, depending on the desired viscosity. NM Gjutharts 347 can also be colored white from the factory.

NM El Epoxy 960/980 is a two component low-viscosity epoxyresin for casting and impregnation. Theresin is colored dark blue. The air-release when casted is normally very good, but encapsulation of coils might need use of vacuum.

NM Tooling 179 V / NM Hardener 2962 is a heat-resistant metal powder filled epoxy designed for manufacturing of press-tools. The tools can either be made by a direct casting in a negative mold or by working with casted blocks. Surfaces that have been worked can be polished.

NM Laminating 3070 / H2962 is designed to be used when there are high demands of heat-resistance. Laminates with NM Laminating 3070 / H2962 should first gel at +40°C, that will take about 2 hours and then be post-cured at +150°C. Full cure will take place in approx. 4 hours at +150°C.

NM Laminering 275 is a solvent-free low-viscosity epoxy resin system for use in laminating, gluing and lacquering.

NM Laminating 160 is designed to be used when there are high demands of yellowing-resistance.

NM Tooling 179 / NM Hardener 179B is a metal powder filled epoxy designed for manufacturing of press-tools. The tools can either be made by a direct casting in a negative mold or by working with casted blocks. Surfaces that have been worked can be polished.