Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Electrical Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
¹ - The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
² - Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
³ - UL Ratings shown on the technical datasheet might not cover the full range of thicknesses and colors.
⁴ - Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
| Value | Units | Test Method / Conditions | |
| Tensile Stress (Yield, 50 mm/min) ¹ | 65.0 | MPa | ISO 527 |
| Tensile Stress (Break, 50 mm/min) ¹ | 57.0 | MPa | ISO 527 |
| Tensile Strain (Yield, 50 mm/min) ¹ | 4.4 | % | ISO 527 |
| Tensile Strain (Break, 50 mm/min) ¹ | 9.2 | % | ISO 527 |
| Tensile Modulus (1 mm/min) ¹ | 2650.0 | MPa | ISO 527 |
| Flexural Modulus (2 mm/min) ¹ | 2610.0 | MPa | ISO 178 |
| Flexural Stress (Yield, 2 mm/min) ¹ | 105.0 | MPa | ISO 178 |
| Tensile Modulus (50 mm/min) ¹ | 2610.0 | MPa | ASTM D638 |
| Tensile Strain (Break, type I, 50 mm/min) ¹ | 29.0 | % | ASTM D638 |
| Tensile Strain (Break, type I, 50 mm/min) ¹ | 4.5 | % | ASTM D638 |
| Tensile Stress (Break, type I, 50 mm/min) ¹ | 52.0 | MPa | ASTM D638 |
| Tensile Stress (Yield, type I, 50 mm/min) ¹ | 66.0 | MPa | ASTM D638 |
| Flexural Modulus (1.3 mm/min, 50 mm span) ¹ | 2680.0 | MPa | ASTM D790 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹ | 105.0 | MPa | ASTM D790 |
| Value | Units | Test Method / Conditions | |
| Density ¹ | 1.08 | g/cm³ | ISO 1183 |
| Moisture Absorption (at 23°C, 50% RH) ¹ | 0.05 | % | ISO 62 |
| Water Absorption (at 23°C, saturated) ¹ | 0.25 | % | ISO 62-1 |
| Mold Shrinkage (Flow) ¹ ² | 0.5 - 0.7 | % | SABIC method |
| Specific Gravity ¹ | 1.1 | — | ASTM D792 |
| Melt Flow Rate (at 280°C/5.0 kgf) ¹ | 12.2 | g/10 min | ASTM D1238 |
| Value | Units | Test Method / Conditions | |
| HDT/Af (at 1.8 MPa, Flatw 80*10*4, sp=64mm) ¹ | 118.0 | °C | ISO 75/Af |
| HDT (at 1.82 MPa, 3.2mm, unannealed) ¹ | 116.0 | °C | ASTM D648 |
| HDT (at 0.45 MPa, 3.2 mm, unannealed) ¹ | 131.0 | °C | ASTM D648 |
| Vicat Softening Temperature (Rate B/50) ¹ | 136.0 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/120) ¹ | 138.0 | °C | ISO 306 |
| Coefficient of Thermal Expansion (-40°C to 40°C, flow) ¹ | 8.1e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (-40°C to 40°C, xflow) ¹ | 7.7e-05 | 1/°C | ISO 11359-2 |
| Relative Temperature Index (Electric) ¹ | 110.0 | °C | UL 746B |
| Relative Temperature Index (Mechanical w/impact) ¹ | 105.0 | °C | UL 746B |
| Relative Temp Index (Mechanical w/o impact) ¹ | 110.0 | °C | UL 746B |
| Value | Units | Test Method / Conditions | |
| Comparative Tracking Index ¹ | 2.0 | PLC Code | UL 746A |
| Hot-Wire Ignition (HWI, PLC 1) ¹ | min. 1.5 | mm | UL 746A |
| High Amphere Arc Ignition (HAI, PLC 0) ¹ | min. 1.5 | mm | UL 746A |
| High Voltage Arc Track Rate (PLC) ¹ | 4.0 | PLC Code | UL 746A |
| Arc Resistance (Tungsten, PLC) ¹ | 6.0 | PLC Code | ASTM D495 |
| Value | Units | Test Method / Conditions | |
| Izod Impact (Notched 80*10*4, at 23°C) ¹ | 15.0 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched 80*10*4, at -30°C) ¹ | 12.0 | kJ/m² | ISO 180/1A |
| Charpy (at 23°C, V-notch Edgew 80*10*3, sp = 62mm) ¹ | 17.0 | kJ/m² | ISO 179/1eA |
| Izod Impact (Notched, at 23°C) ¹ | 186.0 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹ | 111.0 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹ | 53.0 | J | ASTM D3763 |
| Value | Units | Test Method / Conditions | |
| Drying Temperature ⁴ | 105 - 110 | °C | — |
| Drying Time ⁴ | 3 - 4 | hrs | — |
| Maximum Moisture Content ⁴ | 0.02 | % | — |
| Melt Temperature ⁴ | 280 - 310 | °C | — |
| Nozzle Temperature ⁴ | 280 - 310 | °C | — |
| Front - Zone 3 Temperature ⁴ | 270 - 310 | °C | — |
| Middle - Zone 2 Temperature ⁴ | 260 - 305 | °C | — |
| Rear - Zone 1 Temperature ⁴ | 250 - 300 | °C | — |
| Mold Temperature ⁴ | 75 - 105 | °C | — |
| Back Pressure ⁴ | 0.3 - 0.7 | MPa | — |
| Screw Speed ⁴ | 10 - 100 | rpm | — |
| Shot to Cylinder Size ⁴ | 30 - 70 | % | — |
| Value | Units | Test Method / Conditions | |
| UL Recognized (94V-1 flame class rating) ³ | min. 1.5 | mm | UL 94 |
| Glow Wire Ignitability Temperature (3.0 mm) ³ | 750.0 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (1.5 mm) ³ | 725.0 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (2.0 mm) ³ | 700.0 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (1.0 mm) ³ | 725.0 | °C | IEC 60695-2-13 |
| Glow Wire Flammability Index (3.0 mm) ³ | 960.0 | °C | IEC 60695-2-12 |
| Glow Wire Flammability Index (1.5 mm) ³ | 960.0 | °C | IEC 60695-2-12 |
| Glow Wire Flammability Index (2.0 mm) ³ | 960.0 | °C | IEC 60695-2-12 |
| Glow Wire Flammability Index (1.0 mm) ³ | 960.0 | °C | IEC 60695-2-12 |
Regulatory & Compliance
- Certifications & Compliance