Products

This product is a filled prototype casting compound on polyurethane base and is flame retardant according to UL 94 V-0 and clasification DIN EN 45545-2: 2013-08 class R24 HL2 Processing preferentially in standard vacuum casting plants.

Ebalta LH 22 / GL is an epoxy laminating resin, which, depending on its application, can be used with the slow GL hardener or the faster GR hardener. They distinguish by minimal physiolgical effects. Regarding dimensional accuracy and –stability, laminates made of ebalta LH 22, even come up to great demands. Due to its long potlife ebalta LH 22/GL is especially suitable for large-area and thick laminates, which also with a thickness of more than 10 mm, applied in one step, cure without any shrinkage at room temperature.

Ebalta MG 453 GF is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Release agent – please see category release agent

ebalta AH 120/ TL-1 is a very thin liquid epoxy resin with high values of strength and dimensional stability. Due to its good impregnating and wetting properties it is suitable as laminating resin for high-strength components with fabrics of glass –or carbon fiber. ebalta AH 120/ TL-1 is suitable for laminating of thin as well as thick laminates with large surface up to a thickness of 10 mm. Mechnical properties basing on test pieces being postcured for 8 hrs. at 80°C Demoulding depending on layer thickness, geometry and room temperature. Check for individual case. Postcuring before demoulding of laminates, if possible.

Ebalta AH 140 / TC 60 is a temperature resistant laminating resin.

Ebalta SG 700 / PUR 5 is a two-component-Polyurethane casting resin, which cures very fast at room temperature. The very good workability and the excellent mechanical properties makes SG 700 a material with versatile application possibilities. ebalta SG 700 A is even more abrasion-resistant, but not so well workable by machine. Displacements, even made of wood, can be filled in. Material should be carefully stirred up/ shaked before use.

Ebalta AH 140 / LI 130-2 is a general purpose resin.

This product is a polyurethane system. The processing is preferably made in customary vacuum pouring plant. Manual processing possible. Mouldmaterial: we recommend silicone molds, for example Silastic® RTV 4234-T4O.

This product is a polyurethane system. Mechanical data according to test pieces post-cured for 8 hrs. at 80°C. No heavy chemical and mechanical stress before 7 days after curing at room temperature (20-23°C).

ebalta 120/GL is a very low-viscous two-component epoxy resin with high strength values and fast curing. Due to its good soaking and wetting characteristics, this resin/hardener mixture is most suitable for solid parts with fabrics made of glass or carbon fibers. AH 120/GL is suitable as laminating resin for both large area- and thick laminates. Due to its almost odorless and skin-friendly GL hardener it is most suitable as laminating resin. With a mixing ratio of 100:40 you reach an about 15°C higher TG, slightly stiffer laminates as well as better impact resistance. The laminate thickness should not exceed 6-7 mm.

Ebalta LH 28-1 / TM is a two components epoxy laminating resin, precuring at room temperature and, depending on postcuring, can be used till 175°C. Since this laminating resin system contains no fillers, it has got good wetting properties and makes a high glass fabric content possible. This leads to a low coefficient of thermal expansion and high strength. Together with aluminum granules, ebalta LH 28-1 is suitable for back filling of heat resistant molds and molding tools. At room temperature the curing takes 7 days and the material can only be used for applications till 60°C.

Ebalta LH 30 / Resin+Hardener is a two components epoxy laminating resin, precuring at room temperature and, depending on postcuring, can be used till 175°C. Since this laminating resin system contains no fillers, it has got good wetting properties and makes a high glass fabric content possible. This leads to a low coefficient of thermal expansion and high strength. Together with aluminum granules, ebalta LH 28-1 is suitable for back filling of heat resistant molds and molding tools.

ebalta MG 425 is processed on a two-component low pressure device. The systems MG 400 / MG 425 / MG 475 are cured with the hardener PUR 19. By mixing MG 425 with MG 400 the E-modulus can variably between 630 – 1550 MPa. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryllacquer- systems. Release agent – please see category release agent

Ebalta AH 100 is a very thin, unfilled epoxy resin, which can be used with different hardeners. Depending on the application the suitable hardener can be mixed with the resin AH 100. AH 100 / TGL is preferentially used for big volume backfillings.

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

Ebalta AH 120 / TGL is a very thin liquid epoxy resin with high values of strength and dimensional stability. Due to its good impregnating and wetting properties it is suitable as laminating resin for high-strength components with fabrics of glass –or carbon fiber. ebalta AH 120/TGL is suitable for laminating of thin as well as thick laminates with large surface up to a thickness of 8 mm. A post-curing should be executed, if possible before demoulding.

This product is a Polyurethane system If the product is cured at room temperature, no entire chemical and mechanical load before 7 days after curing.

Ebalta AH 110 / TGS is a non-filled epoxy resin with high strength and dimensional stability, even at increasing temperature. It also can be used as casting resin with powder fillers as aluminum powder, as laminating resin with glass fabrics and as binding resin with granular fillers as aluminum granules. Depending on the application if just needs to use a different hardener for the mixture. As laminating resin AH 110 / TGS is suitable for thin high solid laminates.

GM 708 is a high-quality, almost odorless 2-components-polyurethane casting compound without any filler. The filler will only be added when mixing both components. The long potlife of more than 45 min makes it possible to cast big-volume parts. Depending on the application, different dry fillers can be used. To get optimum properties, especially low shrinkage, we recommend a high filler content.

ebalta AH 120/TC 60 is a very thin liquid epoxy resin with high values of strength and dimensional stability. Due to its good impregnating and wetting properties it is suitable as laminating resin for high-strength components with fabrics of glass –or carbon fiber. ebalta AH 120/TC 60 is suitable for laminating of thin as well as thick laminates with large surface up to a thickness of 8 mm. A post-curing should be executed, if possible before demoulding.

Ebalta MG 707 / Z 400 is a 2-components polyurethane material, which is cured thermically and used for prototypes. The four mentioned formulations differ in being filled or non-filled and their mechanical properties. The B-components Z 400 (potlife 8-12 min.) and Z 460 (potlife 60-70 min.) are identical and can be mixed with each other to control the reactivity, e.g. potlife. These combinations of Z 400 and Z 460 comp. B can be made any way as long as the totally required quantity of comp. B is observed (for each system). The total amount of Z 400 and Z 460 always has to be 30 g for 100 g comp. A

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

Ebalta GM 727 is a well castable two components polyurethane casting resin, curing slowly at room temperature. This casting resin is particularly suitable for solid casting of dimensionally accurate large-volume models with high temperature resistance. Due to low mixing viscosity of GM 727 you can add 70% filler F-B and about 50% plastic granules to reduce shrinkage to approx. 0.05%.

This product is a polyurethane system. No load on GM 965-70 before 24 hrs. curing at room temperature (23°C) If the product is cured at room temperature, no entire chemical and mechanical load before 7 days after curing. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product.

Ebalta AH 100 is a very thin, unfilled epoxy resin, which can be used with different hardeners. Depending on the application the suitable hardener can be mixed with the resin AH 100. The fast hardener TGS is used for thin laminates and small-volume back fillings.

GM 987 Comp. B (Amine) can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. The postcured material is not UV stable and darkens by and by. However according to our experience the change in color does not affect its utilizability. The mechanical properties will be reached after 7 d at room temperature or post curing of 8 h at 80°C. As bonding agent on aluminum support we recommend our PU coupling paste KP 8.

Ebalta MG 703 / Z 400 is a 2-components polyurethane material, which is cured thermically and used for prototypes. The four mentioned formulations differ in being filled or non-filled and their mechanical properties. The B-components Z 400 (potlife 8-12 min.) and Z 460 (potlife 60-70 min.) are identical and can be mixed with each other to control the reactivity, e.g. potlife. These combinations of Z 400 and Z 460 comp. B can be made any way as long as the totally required quantity of comp. B is observed (for each system).

The product group ebalta SG 2000 consists of high-quality, nearly odorless two-component-Polyurethane casting resins without mixed in filler. The filler is stirred in when the components are mixed. There are different resin components available, which are processed with one hardener. The single types differ in potlife and curing time.

This product is a polyurethane system. Preferential processing in usually used vacuum pouring plants. Maximum wall thicknesses of the parts: from 5 – 10 mm.

Ebalta SG 700 A / PUR 5 is a two-component-Polyurethane casting resin, which cures very fast at room temperature. The very good workability and the excellent mechanical properties makes SG 700 a material with versatile application possibilities. ebalta SG 700 A is even more abrasion-resistant, but not so well workable by machine. Displacements, even made of wood, can be filled in. Material should be carefully stirred up/ shaked before use.

Ebalta IH 16 / hardener slow is a very thin liquid two component epoxy resin with high strength values and high mold resistance. Due to its good soaking and wet-out characteristics the resin/hardener mixture is suitable as infilitration resin for porouse printed parts. The resin/hardener mixture is suitable as an infiltrations resin for porouse printed parts because of its good soaking and wet-out characteristics.

This product is a polyurethane system. The processing is preferably made in customary vacuum pouring plant. Manual processing possible. Maximum wall thicknesses of the parts: from 5 – 10 mm.

Ebalta AH 120 / TG is a Laminating resin.

ebalta SG 150 is a four component acryl casting resin. It consists of 2 liquid components and a hardener powder. Both liquid components are filled with the 1,5 amount in ppw of special aluminum powder. The resin cures within 20-30 minutes to well heat-conducting, heat-resistant molds. The cured molds are very well workable by machines. The structure is extremely dense and the machined areas have an aluminum-like appearance. It is possible to cast any quantity, which can be mixed in one or more containers. Altercating or casting in layers is not possible. Therefore it is very important to determine the casting volume exactly in order to avoid that the mixed quantity is too small. Since the hardener powder is hygroscopic, always seal it air-tight. We recommend to sieve it before each use. Linear shrinkage as per mixture listed in the data sheet. Room temperature and starting temperature of resin components are 21°C as per measurement. For other temperatures or a different content of aluminum powder, shrinkage might also be different.

Ebalta ebatemp is a high-quality two-component Polyurethane casting resin, which is very suitable for the production of vacuum thermoformed moldings. The fast casting resin, which is filled with very fine aluminum powder is very well castable and after curing very well polishable and workable. With ebatemp vacuum thermoformed moldings can be produced within 1-2 hours, these moldings show a temperature capacity of 80-90°C . Post-curing is not necessary. Material should be carefully stirred up/ shacked before use.

Ebalta AH 110 / TGL is an unfilled epoxy resin with high strength values and dimensional stability, even at increased temperature. It can be used as casting resin with powdered fillers as aluminum powder, laminating resin with glass fabric and binder with grainy fillers as aluminum granules. Depending on application the suitable hardener can be mixed with the resin. AH 110/TGL is suitable as laminating resin for big surfaces at a temperature range until 110 °C.