Products

Ebalta MG 453 GF is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Release agent – please see category release agent

This product is a filled prototype casting compound on polyurethane base and is flame retardant according to UL 94 V-0 and clasification DIN EN 45545-2: 2013-08 class R24 HL2 Processing preferentially in standard vacuum casting plants.

The product group ebalta SG 2000 consists of high-quality, nearly odorless two-component-Polyurethane casting resins without mixed in filler. The filler is stirred in when the components are mixed. There are different resin components available, which are processed with one hardener. The single types differ in potlife and curing time.

This product is a polyurethane system. The processing is preferably made in customary vacuum pouring plant. Manual processing possible. Mouldmaterial: we recommend silicone molds, for example Silastic® RTV 4234-T4O.

Ebalta SG 131 / PUR 11 is a Polyurethane system. Material should be carefully stirred up/ shaked before use. Filler content and sales units are on the separate mixing table noted.

This product is a polyurethane system. No load on GM 965-70 before 24 hrs. curing at room temperature (23°C) If the product is cured at room temperature, no entire chemical and mechanical load before 7 days after curing. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product.

This product is a Polyurethane system If the product is cured at room temperature, no entire chemical and mechanical load before 7 days after curing.

Ebalta SG 700 A / PUR 5 is a two-component-Polyurethane casting resin, which cures very fast at room temperature. The very good workability and the excellent mechanical properties makes SG 700 a material with versatile application possibilities. ebalta SG 700 A is even more abrasion-resistant, but not so well workable by machine. Displacements, even made of wood, can be filled in. Material should be carefully stirred up/ shaked before use.

GM 986-1 Comp. B (Amine) can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. This material is most suitable for high pressure molding plants with high molding pressure and temperature resistance. For application at 60°C Shore hardness D is between 60-62! The postcured material is not UV stable and darkens by and by. However according to our experience the change in color does not affect its utilizability. As bonding agent on aluminum support we recommend our PU coupling paste KP 8. The material is also dimensionally stable at high temperatures. At a mold temperature of approx. 60°C a Shore hardness D of 62-64 will still be reached. Due to remanent brittleness, for complicated geometries we recommend demoulding after 48 hrs. As bonding agent on aluminum support we recommend our PU coupling paste KP 8.

ebalta MG 321 FR is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryllacquer- systems. As release agent you can use our T 03-01. MG 321 FR beige fire behavior according to UL 94, 3 mm thickness V0 With MG 883 the potlife of MG 321 FR beige can be set up to 120 secs. MG 321 FR-S beige/ black - Approved according to UL 94 - File E191776 Vol. 1 fire behavior based on UL 94, 3 mm thickness V0 and 5VA

This product is a polyurethane system. GM 984-1 Comp. B (Amine) can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. The postcured material is not UV stable and darkens by and by. However according to our experience the change in color does not affect its utilizability. Physical final properties will be achieved after 7 days' curing at room temperature or after postcuring for 8 hrs. at 80°C. As bonding agent on aluminum support we recommend our PU coupling paste KP 8.

Ebalta ebatemp is a high-quality two-component Polyurethane casting resin, which is very suitable for the production of vacuum thermoformed moldings. The fast casting resin, which is filled with very fine aluminum powder is very well castable and after curing very well polishable and workable. With ebatemp vacuum thermoformed moldings can be produced within 1-2 hours, these moldings show a temperature capacity of 80-90°C . Post-curing is not necessary. Material should be carefully stirred up/ shacked before use.

GM 987 Comp. B (Amine) can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. The postcured material is not UV stable and darkens by and by. However according to our experience the change in color does not affect its utilizability. The mechanical properties will be reached after 7 d at room temperature or post curing of 8 h at 80°C. As bonding agent on aluminum support we recommend our PU coupling paste KP 8.

Ebalta HFG / PUR 11 is a light filled 2-components-polyurethane casting compound, which cures fast at room temperature. After curing this material is dimensional accurate light weight but anyway resistant, which is especially suitable for big volume backfilling of coreboxes and negative molds. For bigger wall thickness it is possible to mix about 35 volume parts "Kunststoffgranulat" (=synthetic granules) in comp. A in advance

This product is a polyurethane system. Mechanical data according to test pieces post-cured for 8 hrs. at 80°C. No heavy chemical and mechanical stress before 7 days after curing at room temperature (20-23°C).

This product is a polyurethane system. Preferential processing in usually used vacuum pouring plants. Maximum wall thicknesses of the parts: from 5 – 10 mm.

Ebalta GM 727 is a well castable two components polyurethane casting resin, curing slowly at room temperature. This casting resin is particularly suitable for solid casting of dimensionally accurate large-volume models with high temperature resistance. Due to low mixing viscosity of GM 727 you can add 70% filler F-B and about 50% plastic granules to reduce shrinkage to approx. 0.05%.

ebalta MG 425 is processed on a two-component low pressure device. The systems MG 400 / MG 425 / MG 475 are cured with the hardener PUR 19. By mixing MG 425 with MG 400 the E-modulus can variably between 630 – 1550 MPa. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryllacquer- systems. Release agent – please see category release agent

This product is a polyurethane system. Mechanical data according to test pieces post-cured for 8 hrs. at 80°C. No heavy chemical and mechanical stress before 7 days after curing at room temperature (20-23°C).

This product is a polyurethane system. The processing is preferably made in customary vacuum pouring plant. Manual processing possible. Maximum wall thicknesses of the parts: from 5 – 10 mm.

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

This product is a polyurethane system. No load on GM 965-40 before 24 hrs. curing at room temperature (23°C) If the product is cured at room temperature, no entire chemical and mechanical load before 7 days after curing. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product.

Ebalta MG 707 / Z 400 is a 2-components polyurethane material, which is cured thermically and used for prototypes. The four mentioned formulations differ in being filled or non-filled and their mechanical properties. The B-components Z 400 (potlife 8-12 min.) and Z 460 (potlife 60-70 min.) are identical and can be mixed with each other to control the reactivity, e.g. potlife. These combinations of Z 400 and Z 460 comp. B can be made any way as long as the totally required quantity of comp. B is observed (for each system). The total amount of Z 400 and Z 460 always has to be 30 g for 100 g comp. A

Ebalta GM 979 is an easy-to-handle-2components-polyurethane casting compound which shows very low adhesive properties compared to molding sand. Due to its high abrasion resistance, GM 979 is especially suitable for foundry patterns, which have to resist to abrasive wear by molded sand. GM 979 even keeps its high mechanical strength when using molding sands with higher temperatures.

This product is a polyurethane system. "VP"-products are experimental products. Regarding technical data slight modifications are possible.

GM 708 is a high-quality, almost odorless 2-components-polyurethane casting compound without any filler. The filler will only be added when mixing both components. The long potlife of more than 45 min makes it possible to cast big-volume parts. Depending on the application, different dry fillers can be used. To get optimum properties, especially low shrinkage, we recommend a high filler content.

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

Ebalta MG 703 / Z 400 is a 2-components polyurethane material, which is cured thermically and used for prototypes. The four mentioned formulations differ in being filled or non-filled and their mechanical properties. The B-components Z 400 (potlife 8-12 min.) and Z 460 (potlife 60-70 min.) are identical and can be mixed with each other to control the reactivity, e.g. potlife. These combinations of Z 400 and Z 460 comp. B can be made any way as long as the totally required quantity of comp. B is observed (for each system).

The product is a Polyurethane system. For improving of the flow characteristics, GM 973 can be preheated to approx. 30°C. The final strength is achieved at room temperature after approx. 3-5 days. By post-curing at 80°C for 5 hours the stated values are achieved in short time. Parts / molds must not be cast with addition curing silicone, since this might lead to faulty reactions when curing the silicone.

Ebalta SG 700 / PUR 5 is a two-component-Polyurethane casting resin, which cures very fast at room temperature. The very good workability and the excellent mechanical properties makes SG 700 a material with versatile application possibilities. ebalta SG 700 A is even more abrasion-resistant, but not so well workable by machine. Displacements, even made of wood, can be filled in. Material should be carefully stirred up/ shaked before use.

Ebalta SG 130 L / PUR 11 is a Polyurethane system. Material should be carefully stirred up/ shaked before use. Filler content and sales units are on the separate mixing table noted

This product is a polyurethane system. After use please close the containers carefully. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product. Seal porous mold surfaces first (ebalta mold sealer). For optimum mold releasing we recommend a special release agent (like T1-1), which can be applied easily with a brush or be sprayed. Releasing of the mold 2-3 times, evaporate for about 20 min. after each releasing.

ebalta MG 426 is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryl-lacquer- systems. Release agent – please see category release agent.

This is a Polyurethane system. Material should be carefully stirred up/ shaked before use. Filler content and sales units are on the separate mixing table noted.

Ebalta SG 140 / PUR 12 is a Polyurethane system. Material should be carefully stirred up/ shaked before use. Filler content and sales units are on the separate mixing table noted.

This product is a polyurethane system. The processing is preferably made in customary vacuum pouring plant. Manual processing possible. Maximum wall thicknesses of the parts: from 5 – 10 mm.