Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
Features & Benefits
Applications & Uses
- Applications
- Application Area
- Instructions for Use
- Weigh each 100 grams of PART-A to 100 grams of Hardener PART-B.
- Mix until uniform. Scrape the sides and bottom of container repeatedly during mixing.
- Apply to clean bonding surfaces and cure as recommended to achieve the desired properties.
- Typical cured properties were determined using recommended cure schedule.
- Some difference in properties may occur with the alternate or other cure schedules.
Properties
- Typical Cured Properties
- Handling Properties
- Note
- Typical Cured Properties : Tested at 25°C unless otherwise indicated
- 1 After 7days, Immersed in water at 100°C
- 2 After 7days, Immersed in Isopropanol at Room Temperature
- 3 After 7days, In oven at 150°C
| Value | Units | Test Method / Conditions | |
| Specific Gravity | 1.1 | — | — |
| Hardness | 72 | Shore D | — |
| Lap Shear Strength to Aluminium | 3200 | psi | — |
| Lap Shear Strength to Aluminium ¹ | 1580 | psi | — |
| Lap Shear Strength to Aluminium ² | 2330 | psi | — |
| Lap Shear Strength to Aluminium ³ | 4000 | psi | — |
| T-peel Strength to Aluminum | 23 | pli | — |
| Service Temperature Range | -55 to 110 | °C | — |
| Glass Transition Temperature (Tg) | 50 | °C | — |
| Coefficient of Linear Thermal Expansion (Below Tg) | 94 | 10⁻⁶/°C | — |
| Dielectric Strength | 380 | Volts/mil | — |
| Dielectric Constant (at 1 kHz) | 3.81 | — | — |
| Dissipation Factor (at 1 kHz) | 0.4 | — | — |
| Volume Resistivity | 2x10¹³ | ohm-cm | — |
| Value | Units | Test Method / Conditions | |
| Adhesive | Part A | — | — |
| Hardener | Part B | — | — |
| Mix Ratio by Weight (Adhesive/Hardener) | 100/100 | — | — |
| Mixed Viscosity (at 25°C) | 5000 - 8000 | cps | — |
| Pot Life (at 25°C, 100 grams) | 2 | hours | — |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Curing Information
- Recommended Cure : 2 hr at 65°C
- Alternate Cure : 24-48 hr at 25°C
- Frozen Adhesive
Thaw premixed frozen adhesive at room temperature for 5-10 minutes. Dispense adhesive and cure at recommended schedules.
Safety & Health
- Safety Information
- For Industrial Use Only : Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning : Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet (MSDS) for additional health and safety information.
Packaging & Availability
- Packaging Type
- Packaging Options
- 2 parts Kit : Packaged in Pint, Quart, Gallon, and 5-Gallon size. Also available in 50mL and 400mL dual cartridges.
- Premixed and frozen : Packaged in 3cc, 5cc, 10cc and 30cc disposable syringes and ship in dry ice at -80°C
Storage & Handling
- Shelf Life
- 1 Year (Two Parts Kit at 25°C), 1 Year (Frozen at -40°C)