Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
- Labeling Claims
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Potential Applications
PC based LNP THERMOCOMP™ compounds may be qualified to use in consumer electronics, industrial applications for combination of dimensional stability, thin wall and non-Br/Cl Eco FR systems.
Properties
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Electrical Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
| Value | Units | Test Method / Conditions | |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 110 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 2.7 | % | ASTM D638 |
| Tensile Modulus (at 5 mm/min) ¹¹ | 6680 | MPa | ASTM D638 |
| Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹ | 167 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 6150 | MPa | ASTM D790 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 112 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 2.6 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 6800 | MPa | ISO 527 |
| Flexural Stress (Break, 2 mm/min) ¹¹ | 165 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 6240 | MPa | ISO 178 |
| Value | Units | Test Method / Conditions | |
| Density ¹¹ | 1.35 | g/cm³ | ASTM D792 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.2 - 0.4 | % | ASTM D955 |
| Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ | 0.2 - 0.4 | % | ASTM D955 |
| Melt Flow Rate (at 300°C, 1.2 kgf) ¹¹ | 12 | g/10 min | ASTM D1238 |
| Melt Flow Rate (at 300°C, 2.16 kgf) ¹¹ | 24 | g/10 min | ASTM D1238 |
| Water Absorption (at 23°C, saturated) ¹¹ | 0.07 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.03 | % | ISO 62 |
| Melt Volume Rate (at 300°C, 1.2 kg) ¹¹ | 10 | cm³/10 min | ISO 1133 |
| Melt Volume Rate (at 300°C, 2.16 kg) ¹¹ | 20 | cm³/10 min | ISO 1133 |
| Value | Units | Test Method / Conditions | |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 121 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 116 | °C | ASTM D648 |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 121 | °C | ISO 75/Bf |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 117 | °C | ISO 75/Af |
| Vicat Softening Temperature (Rate A/50) ¹¹ | 131 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 123 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 125 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹¹ | 0.000026 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, xflow) ¹¹ | 0.000073 | 1/°C | ISO 11359-2 |
| Relative Temperature Index (Electrical) ᵖ ¹¹ | 80 | °C | UL 746B |
| Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 80 | °C | UL 746B |
| Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 80 | °C | UL 746B |
| Value | Units | Test Method / Conditions | |
| High Ampere Arc Ignition (PLC 0) ¹¹ | min. 0.6 | mm | UL 746A |
| Comparative Tracking Index (UL, PLC) ¹¹ | 3 | PLC Code | UL 746A |
| High Voltage Arc Track Rate (PLC) ¹¹ | 0.00E+00 | PLC Code | UL 746A |
| Hot Wire Ignition (PLC 0) ¹¹ | min. 0.6 | mm | UL 746A |
| Comparative Tracking Index ¹¹ | 200 | V | IEC 60112 |
| Dielectric Strength (in oil, at 1mm) ¹¹ | 40 | kV/mm | IEC 60243-1 |
| Volume Resistivity ¹¹ | 10000000000000000 - 100000000000000000 | Ω.cm | IEC 62631-3-1 |
| Arc Resistance (Tungsten, PLC) ¹¹ | 7 | PLC Code | ASTM D495 |
| Dielectric Constant (at 1.1 GHz) ¹¹ | 3.24 | — | SABIC method |
| Dielectric Constant (at 1.9 GHz) ¹¹ | 3.28 | — | SABIC method |
| Dielectric Constant (at 5 GHz) ¹¹ | 3.28 | — | SABIC method |
| Dielectric Constant (at 10 GHz) ¹¹ | 3.27 | — | SABIC method |
| Dissipation Factor (at 1.1 GHz) ¹¹ | 0.0067 | — | SABIC method |
| Dissipation Factor (at 1.9 GHz) ¹¹ | 0.0066 | — | SABIC method |
| Dissipation Factor (at 5 GHz) ¹¹ | 0.007 | — | SABIC method |
| Dissipation Factor (at 10 GHz) ¹¹ | 0.0072 | — | SABIC method |
| Value | Units | Test Method / Conditions | |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 13 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 9.00E+00 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*3, at 23°C) ¹¹ | 13 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*3, at -30°C) ¹¹ | 9 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 48 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at -30°C) ¹¹ | 56 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*3, at 23°C) ¹¹ | 48 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*3, at -30°C) ¹¹ | 54 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*3 sp=62mm) ¹¹ | 15 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*3 sp=62mm) ¹¹ | 1.00E+01 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 14 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*3 sp=62mm) ¹¹ | 55 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*3 sp=62mm) ¹¹ | 67 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 59 | kJ/m² | ISO 179/1eU |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 715 | J/m | ASTM D4812 |
| Izod Impact (Notched, at 23°C) ¹¹ | 150 | J/m | ASTM D256 |
| Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ | 21 | J | ASTM D3763 |
| Value | Units | Test Method / Conditions | |
| Drying Temperature ⁷ | 110 | °C | — |
| Drying Time ⁷ | 3 - 6 | Hrs | — |
| Maximum Moisture Content ⁷ | 0.02 | % | — |
| Melt Temperature ⁷ | 285 - 310 | °C | — |
| Nozzle Temperature ⁷ | 285 - 305 | °C | — |
| Front - Zone 3 Temperature ⁷ | 280 - 300 | °C | — |
| Middle - Zone 2 Temperature ⁷ | 270 - 290 | °C | — |
| Rear - Zone 1 Temperature ⁷ | 260 - 280 | °C | — |
| Mold Temperature ⁷ | 80 - 110 | °C | — |
| Back Pressure ⁷ | 0.1 - 0.3 | MPa | — |
| Screw Speed ⁷ | 50 - 90 | rpm | — |
| Value | Units | Test Method / Conditions | |
| Glow Wire Ignitability Temperature (at 0.6 mm) ᵖ | 850 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (at 1.5 mm) ᵖ | 875 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (at 3.0 mm) ᵖ | 875 | °C | IEC 60695-2-13 |
| Glow Wire Flammability Index (at 0.6 mm) ᵖ | 960 | °C | IEC 60695-2-12 |
| Glow Wire Flammability Index (at 1.5 mm) ᵖ | 960 | °C | IEC 60695-2-12 |
| Glow Wire Flammability Index (at 3 mm) ᵖ | 960 | °C | IEC 60695-2-12 |
| UL Recognized (94V-0 Flame Class Rating) ᵖ | min. 0.6 | mm | UL 94 |
| UL Recognized (94V-1 Flame Class Rating) ᵖ | min. 0.4 | mm | UL 94 |
| UL Recognized (94V-2 Flame Class Rating) ᵖ | min. 0.3 | mm | UL 94 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability