Products results

Lucobit® 1220 by Lucobit AG is comprised of Crosslinkable Polyethylene and Polyethylene Copolymer. It is commonly used It is available in Granules form.

Smooth-Cast™ ONYX™ SLOW is a mercury-free urethane resin that cures at room temperature to a deep black, solid plastic. ONYX™ resins offer the convenience of a 1A:1B by volume mix ratio and have very low viscosities, so they are easy to mix and pour. ONYX™ resins have an ultimate Shore hardness of 80D and offer higher physical properties and higher heat resistance vs. other general purpose resins. ONYX™ resins are available in 2 speeds. ONYX™ FAST resin has a pot life of 2.5 minutes and a cure time of 10-15 minutes, while ONYX™ SLOW has a pot life of 5 minutes and a cure time of 90 minutes.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

Durez™ 32962 by Sumitomo Bakelite Company is comprised of Phenolic Compound. It is commonly used Durez™ 32962 is certified as UL Flame Rated. It is available in Granules form.

MB 1150 is an Avocado colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1150 is low density foam of approximately 15lbs/ft³ board. Easily cut using CNC machining equipment or by hand the MB 1150 is perfectly suited for temporary master models, architectural design models, foundry patterns as well as design verification and prototype tools.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

Siropol DE-33C resin is low viscosity, high reactivity, general­purpose, and unsaturated polyester resin. The raw materials used in the manufacture of this resin are listed as acceptable in FDA regulation Title 21 CFR 177.2420” for repeated use in contact with food subject to user’s compliance with the prescribed limitations of that regulation.

KPR 6410 by Kemrock Industries and Exports is an orthophthalate-based unsaturated polyester resin (UPR). It is available as liquid and cast resin. Offers excellent mechanical and corrosion resistance properties. KPR 6410 is used in roof lights.

SIROPOL 7440 resin is medium viscosity, excellent fiber wet­out and resilient polyester resin. The raw materials used in the manufacture of this resin are listed as acceptable in FDA regulation Title 21 CFR 177.2420 for repeated use in contact with food subject to user’s compliance with the prescribed limitations of that regulation.

BC 7009-1 is an iron oxide filled, low-cost mass casting system. Thicknesses up to two inches in non-conductive molds, and four inches in conductive molds can be achieved without foaming or yielding excessive shrinkage. Ideal for stretch forms, patterns, dies, molds, duplications, prototypes, etc.

Epoxy OH is a pigmented, thixotropic, solvent-free two-component epoxy resin. It shows high dimensional stability under heat as well as impact- and wearresistance. It is available in white and blue.

This product is a polyurethane system. No load on GM 965-70 before 24 hrs. curing at room temperature (23°C) If the product is cured at room temperature, no entire chemical and mechanical load before 7 days after curing. The product can be subject to color variations due to raw materials, but these color variations have no influence on the quality and the properties of the product.

Duresco NU 461 R is a Epoxy molding compound with excellent thermal shock and chemical resistance for high temperature applications.

BB Resins BB-EPA 1100 is a medium viscosity unmodified epoxy resin obtained by blend of Bisphenol A/Bisphenol F based resins.

RALUPOL® UP 4566 molding compounds are characterized by excellent dimensional stability with very low processing and post-shrinkage. Due to their high rigidity and excellent heat resistance, RALUPOL® products withstand short-term heat loads. They have excellent electrical insulation and dielectric properties, which are retained even with long-term use at high temperatures. The reason for this is high tracking resistance (CTI> 600 V), arc resistance, glow wire test (GWFI 960 ° C) and a high electrical RTI (relative temperature index) of 170 ° C according to UL 746 (IEC 60216 / T1).

RAKU® TOOL PF-3708 has the following properties: unfilled, very low viscosity, high fill rate capability, good cure, very high strength, and good temperature resistance.

Beetafin™ BF2819 is a water based Polyurethane emulsion having excellent compatibility with most common water-based systems. The product is suitable for application to a variety of substrates where high quality and longevity are prime requirements.

RIGIDDI-PAK R-4528 SeriesA black, flame retardant, thermally conductive, high performance series that can be used in all types of electrical components. Combined with its ability to dissipate heat, DI-PAK R-4528 also provides low linear thermal expansion, low shrinkage, and low exothermic heat while curing. Meets UL requirements.

47N is a low-flow epoxy prepreg engineered for binding multilayer epoxy rigid-flex or attaching heatsinks to multilayer PCBs. An optional low lamination temperature protects components already mounted on the PCB.

CLH6230 is a semi-flexible epoxy casting system. This product was specifically developed for potting/casting of electrical and electronic components. The long pot life of the material makes it suitable for large mass castings or heat induced curing with minimal stress. Product passes Ul 94-Hb In-house flammability testing. for a softer system, Clr 350 is recommended. using the same cure schedule, Clr 3516, a black version of Clr 3517, passed class B, 130C. when tested to Ul 1446.

Raptor Resins BMI-1 is a high-temperature Bismaleimide resins with features that you may need in your application.

Polyurethane (PUR) based compound. Glass fibres. Very good noise reduction. Good impact resistance even at low temperature.

Depol Т-810 is a non pre-accelerated unsaturated thixothropic polyester halogenated resin based on chlorendic anhydride. It is formulated for hand lay-up as well as for spray-up, RTM-technologies.

Durez™ SUMIKON PM-9501 by Sumitomo Bakelite Company is comprised of Phenolic Compound. It is commonly used Durez™ SUMIKON PM-9501 is certified as UL Flame Rated. It is available in Granules form.

Ares P106 is orthophthalic resin with medium-low reactivity and good elongation. Peak controlled. The wettability of the fillers is excellent.

Ebalta AH 110 / TGS is a non-filled epoxy resin with high strength and dimensional stability, even at increasing temperature. It also can be used as casting resin with powder fillers as aluminum powder, as laminating resin with glass fabrics and as binding resin with granular fillers as aluminum granules. Depending on the application if just needs to use a different hardener for the mixture. As laminating resin AH 110 / TGS is suitable for thin high solid laminates.

KPR 6200 by Kemrock Industries and Exports is a general purpose, orthophthalate-based unsaturated polyester resin (UPR). It is available as liquid and cast resin. Offers excellent mechanical and corrosion resistance properties. KPR 6200 is used in boats and marine applications. Approved by Lloyd’s Register of Shipping.

A black epoxy system with a convenient 1:1 mix ratio by volume. This product has excellent machinability, good impact strength, and cures overnight at room temperature. It has very low shrinkage making it ideal for prototypes, models, dies, and cast production parts.

CLH6441 is a filled, room temperature cure, two component epoxy system. The system is suitable for potting and encapsulating electrical and electronic components. The products use of non-abrasive filler and convenient mix ratio makes it suitable for processing in automatic dispense equipment. This product is certified with ul and passes ul94-v1 flammability testing.

Duresco NU 6110 T/NU 6110 V is a Glass fiber reinforced epoxy molding compound with very good mechanical properties for high temperature applications.

MB 1100 is an Olive colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1100 is low density foam of approximately 10lbs/ft³ board. Easily cut using CNC machining equipment or by hand the MB 1100 is perfectly suited for temporary master models, architectural design models, foundry patterns as well as design verification and prototype tools.

BCC Kwik Kast/Black is a two component, fast setting polyurethane reproduction plastic. BC 8001 sets to a demoldable hardness within 30 minutes @ 77°F. Uses include; tracing models core boxes, duplicating aids, patterns, prototypes, low temperature vacuum form tools, etc.Handling Properties:BCC's Kwik Kast/Black is a fast-setting, two part casting system which requires careful preparation prior to mixing parts A and B. Because Kwik Kast/Black contains components of high density there will be some separation at the bottom of each container. Using a paint shaker, jiffy mixer, or mixing spatula, re-suspension of the ingredients is easily accomplished. Precaution should be taken to prevent any moisture contamination from containers or utensils. It is recommended that the work area be well ventilated and normal cleanliness and safety rules be observed. Avoid prolonged exposure to vapors and contact with skin.Preparation of Mold Surface:Clean the surface from dust and possible presence of moisture. Apply BC 87 Parting Agent and polish to a uniform high gloss finish (usually 2-3 coats are recommended). For plaster or wood surfaces seal with PVC sealer to ensure complete absence of moisture, followed by 2-3 coats of 87 Parting Agent.Mixing and Pouring:Although not necessary, best results are obtained by evacuation of each component under 29 inches of vacuum which removes entrapped air prior to blending the two components. Pour weighed or measured amounts of Part A & B into a separate dry container by pouring Part A into Part B. Mix with a spatula or mechanical stirrer for 30-40 seconds for quart size batches or 40-50 seconds for gallon batches while avoiding air entrapment. Immediately pour mixed resin uninterrupted from a convenient height above the mold cavity. Clean your mixing tools by rinsing in an alcohol type solvent. Larger masses (2 feet or more) may be built up with successive pours. Castings may be demolded within 30-60 minutes but should be properly supported while "green". Under normal conditions, maximum hardness or cure will be achieved in 12-18 hours.

Duresco NU 3723 N is a Glass fiber reinforced epoxy molding compound with high temperature resistance and very good dimensional stability.Excellent chemical resistance.

CLR1190 is an exceptionally tough epoxy casting system with excellent low temperature thermal and mechanical shock resistance.

Durez™ 29502 by Sumitomo Bakelite Company is comprised of Phenolic Compound. It is commonly used It is available in Granules form.