Products

MOCOM Compounds TEDUR® L 9510-1 is a polyphenylene sulfide-based polymer with a 40% glass fiber filler/additive system. It has high stiffness, making it suitable for pump components and various other applications. During processing injection molding, the melt temperature should be between 320-340°C and the mold temperature should be higher than 140°C.

MOCOM Compounds TEDUR® L 9903-1 is a base polymer composed of Polyphenylene Sulfide and 70% special filler, with special features of increased thermal conductivity, electrostatic dissipation, high density, and magnetisability. It is suitable for pre-drying conditions in a dry air (dessiccant) dryer at a temperature of 130-140°C for 2-4 hours, depending on moisture content and processing injection molding with a melt temperature of 320-340°C and a mold temperature greater than 140°C. This product is suitable for the automotive, machinery, electrical, and electronic market segments and is typically used for applications such as coil formers/bobbins. It is an ideal choice for high-heat applications.

MOCOM Compounds TEDUR® L FC 9510-6 is a polyphenylene sulfide base polymer filled with 40% glass fibers, designed for the machinery market segment. It is used for applications such as pipe fitting, pump components, and ducting/piping systems. It has high stiffness and is recommended to be pre-dried with a dry air (dessiccant) dryer at 130-140°C for 2-4 hours, depending on moisture content, before injection molding. For injection molding, the melt temperature should be 320-340°C, and the mold temperature should be greater than 140°C.

MOCOM Compounds TEDUR® L 9220-1 is a base polymer of Polyphenylene Sulfide filled/additive system with 65% glass fiber/mineral that offers features such as high stiffness, good hydrolysis resistance, and oil resistance. For processing injection molding, it should be melted at a temperature of 320-340°C and the mold temperature should be greater than 140°C. It is used in the Automotive and Machinery market segment, and its typical applications include injection molded parts for highly stressed parts.

MOCOM Compounds TEDUR® L 9214-1 is a base polymer of polyphenylene sulfide with a filler/additive system of 45% glass fibers and 20% mineral. It is designed for highly stressed parts in the automotive and machinery market segments, and has special features of high stiffness. Pre-drying conditions include a dry air (dessiccant) dryer at 130-140°C for 2-4 hours depending on moisture content. Processing includes injection molding with a melt temperature of 320-340°C and a mold temperature greater than 140°C.

MOCOM Compounds TEDUR® L 9511-2 is a Polyphenylene Sulfide (PPS) base polymer filled with 45% glass fibers that offers high stiffness. It is typically used in the automotive, machinery, and injection molded parts markets for applications such as pump components, pump impellers, housings, and high pressure vessels. Pre-drying conditions for TEDUR® L 9511-2 involve drying in a dry air (dessiccant) dryer at 130-140°C for 2-4 hours depending on the moisture content. Processing injection molding requires a melt temperature of 320-340°C and a mold temperature of less than 140°C.

MOCOM Compounds TEDUR® L 9107-1 U is a polyphenylene sulfide-based injection molding grade with 40% glass fibers as a filler/additive system. It has high toughness, reduced flash, and increased burst strength, making it suitable for pump components such as pump impellers. The addition of 40% glass fiber gives TEDUR® L 9107-1 U increased burst strength and high toughness, making it ideal for pump components in demanding environments.

MOCOM Compounds TEDUR® L FC 9510-5 is a Polyphenylene Sulfide base polymer with 40% glass fibers, designed for Machinery, electrical and electronic, building and construction applications. It has high stiffness, easy flow, and is suitable for injection molded parts, pump components, housings and parts in contact with drinking water. Pre-drying conditions should be in a dry air (dessiccant) dryer 130-140°C for 2-4 hours, depending on moisture content. When processing injection molding, a melt temperature of 320-340°C and a mold temperature of greater than 140°C should be used.

MOCOM Compounds ALTECH® PSU FC 1000/100 is a polysulfone base polymer with good flow, used for injection molding of machinery, electrical and electronic parts, and food contact parts. Pre-drying conditions should be done in a dry air (dessiccant) dryer at 130-150°C for 3-4 hours, or an air circulating dryer at 130-150°C for 3-4 hours. Processing injection molding should be done with a melt temperature of 330-380°C and a mold temperature of 120-140°C.

MOCOM Compounds TEDUR® L PPS 1000 15087 is a polyphenylene sulfide base polymer that has been elastomer modified for high toughness. It is suitable for both extrusion and injection molding. The pre-drying conditions should be in a dry air (dessiccant) dryer at 100-130°C for 2-4 hours. The melt temperature for extrusion should be 290-310°C, while the melt temperature and mold temperature for injection molding should be 290-310°C and >100°C respectively. This product is typically used for ducting/piping systems and functional components in the automotive and machinery market segments, providing superior toughness and performance.

MOCOM Compounds TEDUR® L 9422-1 is a base polymer of Polyphenylene Sulfide containing 30% glass fibers and 15% PTFE. It has improved sliding and wear, high stiffness, and high toughness, making it suitable for use in the automotive and machinery market segments for bearings and sliding elements and functional components. Processing Injection molding requires a melt temperature of 320-340°C and a mold temperature of >140°C.

MOCOM Compounds TEDUR® L 9560 S is a Polyphenylene Sulfide injection molding grade with 50% mineral filler/additive system. It has improved surface appearance, high surface gloss, and is metallizable. Pre-drying conditions include drying in a dry air (dessiccant) dryer for 2-4 hours depending on moisture content at 130-140°C. Processing injection molding requires a melt temperature between 320-340°C and a mold temperature above 140°C. Typical applications include reflectors for automotive, lighting and consumer products.

MOCOM Compounds TEDUR® L 9105-1 is a Polyphenylene Sulfide base polymer with 30% glass fiber filler/additive system. It is designed for automotive and machinery applications and is known for its high toughness and stiffness. During processing with injection molding, the melt temperature should be between 320-340°C, and the mold temperature should be greater than 140°C.

MOCOM Compounds TEDUR® L 9114-1 S is a base polymer of Polyphenylene Sulfide containing 60% glass fibers, offering high stiffness and injection molding grade. It is suitable for various applications and should be stored in a dry, light-protected environment not exceeding 30°C. During processing injection molding, melt temperature should be 320-340°C and mold temperature should be greater than 140°C. Ensure that the temperature is not exceeded, otherwise the material may degrade.

MOCOM Compounds TEDUR® L 9560 is a Polyphenylene Sulfide base polymer with a 50% mineral filler/additive system that offers improved surface appearance and high surface gloss. It is used for injection molded parts in the automotive and machinery market segments and typical applications include reflectors. For best results, pre-drying conditions should be in a dry air (dessiccant) dryer at 130-140°C for 2-4 hours, depending on moisture content, followed by processing injection molding with melt temperature 320-340°C and mold temperature greater than 140°C.

MOCOM Compounds TEDUR® L 9404-3.2 is a Polyphenylene Sulfide base polymer with a filler/additive system of 30% carbon fibers, offering reduced surface resistivity, electrically conductive, and high stiffness properties. Typical applications for TEDUR® L 9404-3.2 include functional components and it is suitable for the Automotive, Machinery, electrical and electronic market segments. To ensure optimal performance, it should be stored in a dry, protected environment, not exceeding 30°C and away from light.

MOCOM Compounds TEDUR® L 9300-1 is a Polyphenylene Sulfide base polymer with 40% glass fibers/glass beads filler/additive system, colored black. It has high toughness, reduced flash, increased burst strength, and low warpage, making it suitable for various applications. To ensure optimal performance, TEDUR® L 9300-1 should be protected from light and stored at a temperature not exceeding 30°C. For injection molding, a melt temperature of 320-340°C and a mold temperature greater than 140°C is recommended.

MOCOM Compounds TEDUR® L 9912-1 is a polyphenylene sulfide filled with 60% glass fiber/mineral, used for the injection molding of high-density parts for the automotive and machinery market. The pre-drying conditions require a dry air (dessiccant) dryer at a temperature of 130-140°C for 2-4 hours, depending on the moisture content. For injection molding, the melt temperature should be between 320-340°C, and the mold temperature should be greater than 140°C. Typical applications are varied, and it should be stored in a dark place, and not at a temperature above 30°C.

MOCOM Compounds TEDUR® L 9116-1 is a base polymer of Polyphenylene Sulfide filled with 60% glass fibers. It has pre-drying conditions of 130-140°C for 2-4 hours in a dry air (dessiccant) dryer and is processed through injection molding with a melt temperature of 320-340°C and a mold temperature above 140°C. It has low warpage, high toughness, and high stiffness and is used in automotive and machinery applications for injection molded parts.

MOCOM Compounds TEDUR® L 9200-1 is a base polymer of Polyphenylene Sulfide that has a filler/additive system of 60% glass fiber/mineral and is known for its high toughness. It is typically used for automotive seals and various applications. For pre-drying, it should be dried in a dry air (dessiccant) dryer for 2-4 hours at 130-140°C, depending on moisture content. For injection molding, the melt temperature should be 320-340°C and the mold temperature should be greater than 140°C.

MOCOM Compounds TEDUR® L 9510-5 is a pre-drying injection molding grade polymer with a base polymer of polyphenylene sulfide. It contains 40% glass fibers, offering high stiffness and easy flow, and is used in various market segments with typical applications such as pump components and housings. The pre-drying conditions involve a dry air (dessiccant) dryer at a temperature of 130-140°C for 2-4 hours depending on the moisture content. The injection molding process requires a melt temperature of 320-340°C and a mold temperature of more than 140°C. Finally, the product should be stored in a cool, dry place and protected from light, at temperatures not exceeding 30°C.

MOCOM Compounds TEDUR® L 9107-7 is a polyphenylene sulfide injection molding grade with 40% glass fibers, featuring high toughness, reduced flash, increased burst strength, low odor, and is suitable for automotive, machinery, and various applications, such as pump components, housings, pump impellers, and high pressure vessels. Processing injection molding requires a melt temperature of 320-340°C and a mold temperature of more than 140°C.

MOCOM Compounds TEDUR® L 9510-1 S is a base polymer of Polyphenylene Sulfide filled with 40% glass fibers, designed for injection molding with pre-drying conditions in a dry air (dessiccant) dryer at 130-140°C for 2-4 hours, depending on moisture content, and melt temperature of 320-340°C and mold temperature of greater than 140°C. It is used for machinery pump components in various applications and should be stored in a cool, dark place, not above 30°C.

MOCOM Compounds TEDUR® L 9107-1 S is a polyphenylene sulfide polymer containing 40% glass fibers designed for injection molding applications. It offers high toughness and reduced flash, with increased burst strength, making it suitable for the machinery market segment. Typical applications include pump impellers. The pre-drying conditions require the material to be placed in a dry air (dessiccant) dryer at a temperature of 130-140°C for 2-4 hours, depending on moisture content. For injection molding, a melt temperature of 320-340°C and mold temperature of greater than 140°C is required.

MOCOM Compounds TEDUR® L 9410-1 is a polymer consisting of a base polymer of Polyphenylene Sulfide with a filler/additive system of 45% glass fiber/mineral and 15% PTFE. It has improved sliding/wear, high stiffness, and low warpage and is typically used for bearing and sliding elements, and functional components in Automotive and Machinery markets. It requires processing injection molding with melt temperatures of 320-340°C and mold temperatures of greater than 140°C for 2-4 hours, depending on moisture content.

MOCOM Compounds TEDUR® L 9904-1 is a Polyphenylene Sulfide base polymer with an 80% special filler/additive system that is used in the automotive, machinery, electrical, and electronic market segments. It has increased thermal conductivity, electrostatically dissipating, high density, and magnetisable properties, and is used for electrical components such as coil formers/bobbins. For processing injection molding, the melt temperature should be 320-340°C and the mold temperature should be greater than 140°C.

MOCOM Compounds TEDUR® L 9406-1 is a Polyphenylene Sulfide base polymer containing 10% carbon fibers and 50% glass fiber/mineral filler/additive system. It has the special features of being electrically conductive, high stiffness, and low warpage, and is typically used in the automotive and machinery market segments for injection molded parts such as bearings and sliding elements and functional components. Pre-drying conditions involve drying in a dry air (dessiccant) dryer at 130-140°C for 2-4 h, depending on moisture content. Processing injection molding requires a melt temperature of 320-340°C and a mold temperature greater than 140°C. Finally, it should be kept away from direct sunlight.

MOCOM Compounds TEDUR® L FC 9510-7 is a polyphenylene sulfide-based polymer containing 40% glass fibers, making it ideal for injection molding due to its high stiffness, easy flow and reduced flash. It is suitable for applications in the machinery, electrical and electronic, and building and construction markets, such as housings and parts in contact with drinking water.

MOCOM Compounds TEDUR® L 9421-1 S is a blend of Polyphenylene Sulfide and 40% glass fibers, 10% PTFE, which has improved sliding/wear, high stiffness, and high toughness properties. It is used in Automotive and Machinery markets for bearings and sliding elements, functional components. The pre-drying conditions involve drying in a dry air (dessiccant) dryer at 130-140°C for 2-4 hours, depending on moisture content. The processing injection molding involves a melt temperature of 320-340°C and a mold temperature greater than 140°C.

MOCOM Compounds TEDUR® L 9217-1 S is a polyphenylene sulfide base polymer filled with 65% glass fiber/mineral and is used in the automotive, machinery, and lighting market segments. It has special features such as high stiffness, hot oil resistance, and good hydrolysis resistance, and is typically used for highly stressed parts. Pre-drying conditions should be done in a dry air (dessiccant) dryer at 130-140°C for 2-4 hours, depending on the moisture content. Processing injection molding should be done at a melt temperature of 320-340°C and a mold temperature of greater than 140°C.

MOCOM Compounds TEDUR® R 9519 is a special injection molding grade containing 45% glass fibers and recycled material, making it suitable for applications such as fixing elements and lamp sockets. Pre-drying is required in a dry air (desiccant) dryer at 130-140°C for 2-4 hours, depending on the moisture content. During processing, injection molding should be done with a melt temperature of 320-340°C and a mold temperature of at least 140°C.

MOCOM Compounds TEDUR® L 9523 is a polyphenylene sulfide base polymer with a 60% glass fiber/mineral filler/additive system, which is black in color. It has high stiffness, improved surface appearance, and is suitable for various applications such as reflectors. Pre-drying conditions should be done in a dry air (dessiccant) dryer at 130-140°C for two to four hours depending on moisture content. For processing injection molding, the melt temperature should be 320-340°C and the mold temperature should be greater than 140°C.

MOCOM Compounds TEDUR® L 9200-1 U is a polyphenylene sulfide base polymer with a filler/additive system of 60% glass fiber/mineral. It is designed for pre-drying conditions in a dry air (dessiccant) dryer at 130-140°C for 2-4 hours, depending on moisture content. Processing injection molding requires a melt temperature of 320-340°C and a mold temperature of more than 140°C. It offers high toughness, high stiffness, low warpage, and low anisotropic shrinkage, making it suitable for use in the automotive and various market segments. It is typically used for applications such as seals.

MOCOM Compounds TEDUR® L 9107-1 is an injection molding grade of Polyphenylene Sulfide base polymer with 40% glass fibers filler/additive system. The melt temperature should be 320-340°C and the mold temperature should be greater than 140°C. It has special features such as high toughness, reduced flash, and increased burst strength. Typical applications include pump components such as pump impellers. For optimal performance, it should be stored dry and protected from light at temperatures not exceeding 30°C.

MOCOM Compounds TEDUR® L 9400-1 is a Polyphenylene Sulfide base polymer with 15% carbon fibers filler/additive system, which has reduced surface resistivity, is electrically conductive, and has high stiffness features. It is typically used for functional components in the Automotive, Machinery, electrical and electronic market segments. Pre-drying should be done in a dry air (dessiccant) dryer at 130-140°C for 2-4 h, depending on moisture content. Processing Injection molding should be done with a melt temperature of 320-340°C and a mold temperature of more than 140°C. Ensure that the material is properly dried before processing.

MOCOM Compounds TEDUR® L 9409-3.2 is a Polyphenylene Sulfide base polymer containing 30% carbon fibers and 15% PTFE filler/additive system. It has reduced surface resistivity, is electrically conductive, and improved sliding/wear characteristics. It is used in the automotive, machinery, electrical and electronic market segment for functional components, housings, bearings and sliding elements. Pre-drying conditions require a dry air (dessiccant) dryer at 130-140°C for 2-4 hours, depending on moisture content. Processing injection molding requires a melt temperature of 320-340°C and a mold temperature greater than 140°C, with appropriate cooling times.