Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Polymer Name
- Technologies
Features & Benefits
- Labeling Claims
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Typical Properties
- Optical Properties
- Flammability
- Processing Information (Injection Molding)
- Rheological Properties
Value | Units | Test Method / Conditions | |
Flexural Modulus | 1600.0 | MPa | ISO 178 |
Flexural Stress (3.5% Strain) | 37.0 | MPa | ISO 178 |
Tensile Modulus | 1700.0 | MPa | ISO 527 |
Tensile Stress at Yield | 27.0 | MPa | ISO 527 |
Tensile Elongation at Yield | 11.0 | % | ISO 527 |
Tensile Elongation at Break | 60.0 | % | ISO 527 |
Impact Strength (Charpy, at 23°C) | no break | kJ/m² | ISO 179/1eU |
Impact Strength (Charpy, at -40°C) | 20.0 | kJ/m² | ISO 179/1eU |
Notched Impact Strength (Charpy, at 23°C) | 10.0 | kJ/m² | ISO 179/1eA |
Notched Impact (Charpy, at -40°C) | 2.0 | kJ/m² | ISO 179/1eA |
Value | Units | Test Method / Conditions | |
Density | 1040.0 | kg/m³ | ISO 1183 |
Value | Units | Test Method / Conditions | |
Vicat B50 | 61.0 | °C | ISO 306 |
Value | Units | Test Method / Conditions | |
Moisture Content | max. 0.02 | % | — |
Value | Units | Test Method / Conditions | |
Total Transmission T(Y) (d=1,0mm, A, 2°) | 77.5 | % | ISO 13468 |
Total Transmission T(Y) (d=2,0mm, A, 2°) | 62.5 | % | ISO 13468 |
Total Transmission T(Y) (d=3,0mm, A, 2°) | 52.5 | % | ISO 13468 |
Total Transmission T(Y) (d=4,0mm, A, 2°) | 45.0 | % | ISO 13468 |
Haze T(Y) (d=1.0 mm, A, 2°) | 93.5 | % | ISO 13468 |
Haze T(Y) (d=2.0 mm, A, 2°) | 95.5 | % | ISO 13468 |
Haze T(Y) (d=3.0 mm, A, 2°) | 95.5 | % | ISO 13468 |
Haze T(Y) (d=4.0 mm, A, 2°) | 95.5 | % | ISO 13468 |
Half Power Angle T(Y) (d=1mm, A, 2°) | 2.0 | Degree | — |
Half Power Angle T(Y) (d=2mm, A, 2°) | 28.0 | Degree | — |
Half Power Angle T(Y) (d=3mm, A, 2°) | 44.0 | Degree | — |
Half Power Angle T(Y) (d=4mm, A, 2°) | 52.0 | Degree | — |
Value | Units | Test Method / Conditions | |
Glow Wire (GWFI, 550°C, 1mm) | Passed | — | DIN EN 60695 |
Glow Wire (GWFI, 550°C, 2mm) | Passed | — | DIN EN 60695 |
Value | Units | Test Method / Conditions | |
Melt Temperature | 200 - 240 | °C | — |
Mould Temperature | 30 - 60 | °C | — |
Value | Units | Test Method / Conditions | |
Melt Index (MVR) | 75.0 | cm³/10min | ISO 1133 |
MVR Temperature | 220.0 | °C | — |
MVR Load | 10.0 | kg | — |
Shrinkage (24h) | 0.3 - 0.7 | % | ISO 294-4 |
Regulatory & Compliance
Technical Details & Test Data
- Pre-Drying Conditions
65 °C in a dry air (dessiccant) dryer for 2-3 h
Storage & Handling
- Storage Conditions
Store in dry, protected from light.