Products in Cellulosics

MOCOM Compounds CELLIDOR® CP 300-13 is a pre-drying condition polymer made of cellulose acetate propionate and 13% phthalate-free plasticiser. It is typically used for various applications. For injection molding, the melt temperature should be between 180-230°C and the mold temperature should be between 40-80°C. The maximum moisture content should not exceed 0.15%.

MOCOM Compounds CELLIDOR® CP 400-12 is an injection molding grade polymer made of Cellulose Acetate Propionate. This product requires pre-drying in an air circulating dryer at 50-80°C for 2-4 hours, depending on moisture content. It contains 12% phthalate-free plasticizer and can be used for various applications.

MOCOM Compounds CELLIDOR® B 501-10 is a Base Polymer of Cellulose Acetate Butyrate that has been pre-dried in either a dry air (dessiccant) dryer at 50-70°C for 1-2 h or an air circulating dryer at 50-70°C for 2-4 h. It is suitable for Processing Injection molding with a melt temperature of 190-235°C and a mold temperature of 40-80°C and is formulated with a phthalate-free plasticiser and other additives to provide good chemical resistance, high light transmission, high surface quality, processing stabilization, injection molding grade, good haptics, and good weathering resistance, making it suitable for various market segments and applications areas with typical applications.

MOCOM Compounds CELLIDOR® CP 300.02-16 is a base polymer made of CelluloseAcetatePropionate, typically used for various applications in the Medical/Personal Care market segment. It contains a phthalate-free plasticiser and light stabilizer filler/additive system. For injection molding, the melt temperature should be 180-230°C, and the mold temperature should be between 40-80°C.

MOCOM Compounds CELLIDOR® CP 410-11 is a base polymer made of cellulose acetate propionate, which is typically used for thick-walled parts. It is pre-dried in an air circulating dryer between 50-80°C for 2-4 h, depending on moisture content, with a maximum moisture content of 0.15%. During processing, injection molding is used with a melt temperature of 180-230°C and a mold temperature of 40-80°C. It contains 11% phthalate-free plasticiser for optimal performance. It should be stored in a dry and light-protected environment, not exceeding 30°C for best results.

MOCOM Compounds CELLIDOR® CP 310-10 is a base polymer of Cellulose Acetate Propionate and is typically used for thick-walled parts. The pre-drying conditions should be in an air circulating dryer at 60-90°C for 2-4 h, depending on the moisture content not exceeding 0.15%. The processing injection molding should have a melt temperature of 180-230°C and a mold temperature of 40-80°C. It also contains a phthalate-free plasticiser as part of the filler/additive system, ensuring that the end product is safe and compliant with regulations.

MOCOM Compounds CELLIDOR® B 500-20 is a base polymer composed of Cellulose Acetate Butyrate and a filler/additive system of 20% phthalate-free plasticiser. It has low odor and is typically used for injection molded parts. For optimal results, it should be stored in a dry, light-protected environment. For injection molding, processing requires a melt temperature of 180-230°C and a mold temperature of 40-80°C. No extra sentences needed.

MOCOM Compounds CELLIDOR® CP 400-10 is a base polymer made of CelluloseAcetatePropionate with a 10% phthalate-free plasticiser. It is typically used in various applications. For pre-drying conditions, it should be placed in an air circulating dryer at 60-90°C for 2-4 hours, depending on the moisture content, with a maximum moisture content of 0.15%. For processing injection molding, the melt temperature should be set between 180-230°C and the mold temperature should be between 40-80°C.

MOCOM Compounds CELLIDOR® CP 2825-11 is a base polymer of cellulose acetate propionate with a phthalate-free filler/additive system of plasticiser and light stabilizer. It has special features of easy flow, high toughness, high stiffness, and UV stabilization, making it suitable for various market segments and applications areas, such as sports equipment and spectacle lenses. For injection molding, the melt temperature should be set between 190-235°C and the mold temperature should be between 40-80°C.

MOCOM Compounds CELLIDOR® CP 400-15 is a base polymer made of Cellulose Acetate Propionate and contains 15% phthalate-free plasticizer. For pre-drying conditions, it should be placed in an air-circulating dryer with a temperature between 50-80°C for 2-4 hours, depending on the moisture content, with a maximum moisture content of 0.15%. For processing injection molding, the melt temperature should be between 180-230°C and the mold temperature should be between 40-80°C. This product has many typical applications.

MOCOM Compounds CELLIDOR® CP FC 400.01-08 is a base polymer composed of cellulose acetate propionate containing 8% phthalate-free plasticiser. It is suitable for injection molding parts, food contact and typical applications such as toothbrushes. Pre-drying conditions should be in an air circulating dryer at 60-90°C for 2-4 h, depending on moisture content, with a maximum moisture content of 0.15%. Processing should be injection molding with a melt temperature of 180-230°C and a mold temperature of 40-80°C. To ensure quality, keep it dry and protected from light.

MOCOM Compounds CELLIDOR® CP 400-08 is a base polymer made of cellulose acetate propionate with 8% phthalate-free plasticiser. Pre-drying conditions should be done in an air-circulating dryer for 2-4 hours at a temperature of 60-90°C, depending on the moisture content with a maximum moisture content of 0.15%. For optimal processing performance, injection molding should be done at a melt temperature of 180-230°C and a mold temperature of 40-80°C.

MOCOM Compounds CELLIDOR® B 631-10 is a cellulose acetate butyrate base polymer used for injection molding with a phthalate-free plasticiser filler/additive system. It is pre-dried in a dry air (dessiccant) dryer or air circulating dryer at temperatures of 50-70°C for 1-2 h or 2-4 h respectively, depending on moisture content. The extrusion melt temperature ranges from 190-235°C, and indie temperature from 40-80°C. It is used in the sport and leisure and various market segments for extruded parts and profiles, with typical applications such as protection-strips and grease reservoirs. The parts produced using this polymer have excellent dimensional stability and high strength.

MOCOM Compounds CELLIDOR® CP 410-18 is a base polymer of Cellulose Acetate Propionate, which is processing stabilized and has a high toughness. It is typically used for various applications. Pre-drying conditions involve air-circulation in a dryer at 50-80°C for 2-4 hours, depending on the moisture content. During injection molding, the melt temperature should range from 180-230°C and the mold temperature from 40-80°C. It is phthalate-free and contains a plasticiser.

MOCOM Compounds CELLIDOR® B 531-10 is a Cellulose Acetate Butyrate polymer with 10% phthalate-free plasticiser. It is used for various applications and pre-dried in an air circulating dryer at a temperature of 60-90°C for 2-4 hours, depending on the moisture content with a maximum moisture content of 0.05%. For processing injection molding, the extrusion melt temperature should range from 180-230°C and the injection molding temperature should be 40-80°C.

MOCOM Compounds CELLIDOR® B 500-10 is a base polymer made of Cellulose Acetate Butyrate, with a filler/additive system of 10% phthalate-free plasticiser and special features of low odor. For pre-drying conditions, it should be placed in an air circulating dryer at 60-90°C for 2-4 hours depending on moisture content, with a maximum moisture content of 0.15%. For processing injection molding, the recommended melt temperature should be 180-230°C, and the mold temperature should be 40-80°C. Typical applications for CELLIDOR® B 500-10 include various industries such as automotive, electronics, and medical.

MOCOM Compounds CELLIDOR® CP 430-13 AG is a base polymer composed of Cellulose Acetate Propionate with 13% phthalate-free plasticiser. Pre-drying conditions require an air circulating dryer with a temperature between 50-80°C for 2-4 h, depending on moisture content, with a maximum moisture content of less than 0.05%. For processing injection molding, an extrusion melt temperature of 180-230°C and an indie temperature of 40-80°C are required.

MOCOM Compounds CELLIDOR® B 500-15 is a cellulose acetate butyrate base polymer with 15% phthalate-free plasticiser. It is suitable for injection molding with melt temperatures ranging from 180-230°C and mold temperatures from 40-80°C. It has the special features of low odor and is used for various applications.

MOCOM Compounds CELLIDOR® B 5111-10 is a polymeric material with a base polymer of Cellulose Acetate Butyrate and a filler-additive system of phthalate-free plasticiser. It is designed for use in injection molding and is processing stabilized, UV stabilized and weather stabilized, making it suitable for use in building and construction applications. It has good chemical resistance, high surface quality, high surface gloss, and good haptics. It is also suitable for use in thick-walled parts and has a high light transmission.

MOCOM Compounds CELLIDOR® CP 400-17 is a base polymer of cellulose acetate propionate with a filler/additive system of 17% phthalate-free plasticiser. For pre-drying conditions, it should be placed in an air circulating dryer for 2-4 hours at a temperature of 50-80°C, depending on the moisture content which should not exceed 0.15%. For processing injection molding, the melt temperature should be set between 180-230°C and the mold temperature should be set between 40-80°C. Typical applications of this product include various applications.

MOCOM Compounds CELLIDOR® B 631-10S is a base polymer of CelluloseAcetateButyrate with a filler/additive system of phthalate-free plasticiser. It is used in the market segment of sport and leisure and its application area is extruded parts and profiles. Typical applications are protection-strip and grease reservoirs. Processing injection molding - extrusion melt temperature is 190-235°C, with an inlet temperature of 40-80°C.

MOCOM Compounds CELLIDOR® B 631-12,5 is a cellulose acetate butyrate polymer with a phthalate-free plasticiser system of 12-13%, a light stabilizer, and added features of high toughness, high surface quality, high surface gloss, good haptics, and good weathering resistance. It is used for extruded parts and profiles.

MOCOM Compounds CELLIDOR® B 531-07 is a base polymer made of cellulose acetate butyrate and contains a filler/additive system of 7% phthalate-free plasticiser. It is suitable for processing injection molding with an extrusion melt temperature of 180-230°C and an indie temperature of 40-80°C. Typical applications for CELLIDOR® B 531-07 are varied and include automotive parts, toys, and furniture components.

MOCOM Compounds CELLIDOR® CP 300-10 is a base polymer composed of cellulose acetate propionate, with a 10% phthalate-free plasticiser. It is suitable for use in the production of toothbrushes and other products. It should be pre-dried in an air circulating dryer at temperatures between 60-90°C for 2-4 hours, depending on the moisture content. For injection molding, the melt temperature should be between 180-230°C and the mold temperature should be between 40-80°C. No extra sentence required.

MOCOM Compounds CELLIDOR® CP 300-18 is a base polymer composed of cellulose acetate propionate, with an 18% phthalate-free plasticiser. It is suitable for injection molding, with a melt temperature of 180-230°C and a mold temperature of 40-80°C. Typical applications include various injection molded parts.

MOCOM Compounds CELLIDOR® CP 2810-11 is a processing injection molding material with a melt temperature range of 190-235°C, a mold temperature range of 40-80°C, a base polymer of cellulose acetate propionate, a filler/additive system of phthalate-free plasticiser, and special features including easy flow, high toughness, high stiffness and UV stabilization. It is suitable for the sport and leisure market segment and for the production of various injection molded parts, with typical applications including various uses.

MOCOM Compounds CELLIDOR® CP 410-10 is a base polymer made of cellulose acetate propionate with a 10% phthalate-free plasticiser added as a filler/additive system. Pre-drying conditions involve an air circulating dryer at 60-90°C for 2-4 h, depending on the moisture content which should not exceed 0.15%. When processed via injection molding, the melt temperature should be between 180-230°C and the mold temperature should be between 40-80°C. Typical applications for this material include thick-walled parts with good strength and durability.

Rotuba MSS is a scented acetate.

Rotuba H is a scented acetate.

Rotuba H2 is a scented acetate.

Rotuba H3 is a scented acetate.

Rotuba H4 is a scented acetate.

Rotuba MH is a scented acetate.

Arboform® L, V100 Natur is made from 100% renewable raw materials and is biodegradable. This material contains lignin, which is second only to cellulose as the most abundant natural polymer. Lignin is a by-product of the pulp industry and the volume produced worldwide is about 50 million tons per year. Mixing lignin with natural fibers (flax, hemp or other fiber plants) and natural additives produces a fiber composite that can be processed at raised temperatures and pressure and made into moldings on plastic injection molding machines.

Arboform® ZE 50 Natur is made from 100% renewable raw materials and is biodegradable. This material contains lignin, which is second only to cellulose as the most abundant natural polymer. Lignin is a by-product of the pulp industry and the volume produced worldwide is about 50 million tons per year. Mixing lignin with natural fibers (flax, hemp or other fiber plants) and natural additives produces a fiber composite that can be processed at raised temperatures and pressure and made into moldings on plastic injection molding machines.

Zelfo Technology Zelfo HG is a Patented fiber engineering technologies developed by Zelfo Technology can transform 100% renewable or recycled cellulose fibers into self-binding Zelfo® materials.