Products

ME7656 is a reworkable, boron-nitride crystallite filled, electrically insulating and thermally conductive epoxy paste adhesive. It exhibits outstanding flexibility for bonding materials with highly mismatched CTE's (i.e., alumina to aluminum, silicon to copper). The very high thermal conductivity of this material makes it useful for bonding high- powered, large area die and components.

SR8850-1 is a room temperature curable, silver coated copper filled, electrically conductive RTV silicone sealant/adhesive. It can be used as a coating if dissolved or diluted with low boiling point solvent, such as naphtha. The material has no corrosive by-products and has good adhesion properties to metals, plastics, silicones, ceramics and glass. It is useful for bonding large area substrates and components of any size. The material is provided as a one-part electrically conductive elastomer/silicone with a compatible primer. The silicone cures when exposed to atmospheric conditions. The typical curing schedule is 24 hours at 25°C and 60% relative humidity. Using a large volume of paste requires a cure schedule of 48 hours at 25°C and 60% relative humidity.

CC7130-PRTC is a low viscosity version of CC7130-PR for thin coating. It is a translucent coating liquid. It provides excellent protection for electronic components and devices that are highly sensitive to moisture. CC7130 PRTC, coated on PCB, provides more than 200 giga-ohm resistance at 1000 volt even when the board is in direct contact with salt water. It protects PCB to 1000 volt even after prolong exposure to 85CI85% humidity. In accelerated aging test, submerging in 5 wt% salt waters at 60°C, it protects copper surfaces for >24 hours. It is flexible to withstand extreme temperature cycles in Outdoor environment. CC7130-PRTC can easily be dispensed using conventional tools without vacuum deposition equipment. Compared to acrylic or urethane materials, CC7130-PRTC material has low moisture absorption and low moisture transmission rate.

ME7155-AN is a reworkable, aluminum nitride filled, electrically insulating and thermally conductive epoxy paste adhesive which exhibits outstanding flexibility for bonding materials having highly mismatched CTE's (i.e., alumina to aluminum, silicon to copper). The high thermal conductivity of this material makes it useful for bonding high-powered, large area die and components. It can be readily reworked at 80-100°C.

ME8630-RC is an extra fine silver filled 100% solid rapid curing die- attach for finer pitch application. It is a low stress, low temperature curable die-attach adhesive paste. This single component, silver filled paste is electrically and thermally conductive. It is highly thixotropic with outstanding compatibility for bonding different adherends. The relatively medium Tg and modulus made it suitable for bonding both smaller and relatively large devices. ME8630-RC has been designed to eliminate bleeding on both silver plated copper and alloy 42 lead frames. It maintains more than 150 psi bond strength at 250°C for high temperature wire-bonding.

ME7155 is a reworkable, alumina filled, electrically insulating and thermally conductive epoxy paste adhesive. It exhibits not only outstanding flexibility for bonding materials having highly mismatched CTE's (i.e., alumina to aluminum, silicon to copper), but also exhibits high level of uniformity and consistency in appearance and smoothness of texture, yielding potential ease of use and success in applications. The high thermal conductivity of this material makes it useful for bonding high-powered, large area die and components. MEZ155 can be readily reworked at 80-1502.

EG8020 is a two-part, silver filled, room temperature curable adhesive upon mixing. This paste has good bond strength and is both electrically and thermally conductive. The easy mix ratio of 1:1 by weight or volume and ambient curable with long pot-life enable the adhesive to be used for small volume field and larger volume production applications.

ME8630-DA is an extra fine silver filled 100% solid low viscosity die-attach for finer pitch application. It is a low stress, low temperature curable die-attach adhesive paste. This single component, silver filled paste is electrically and thermally conductive. It is highly thixotropic with outstanding compatibility for bonding different adherends. The relatively medium Tg and modulus made it suitable for bonding both smaller and relatively large devices. ME8630-DA has been designed to eliminate bleeding on both silver plated copper and alloy 42 leadframes. It maintains more than 300 psi bond strength at 250°C for high temperature wire-bonding.

EG7658 is a reworkable, aluminum nitride filled, electrically insulating and thermally conductive epoxy paste adhesive. It which exhibits outstanding flexibility for bonding materials with highly mismatched CTE's (ie., alumina to aluminum, silicon to copper). The high thermal conductivity and flexibility make it excellent for bonding high-powered, large area die and components. EG7658 can be reworked using temperatures higher than the cure temperature from 80-150°C to soften the bond line. Use a tool adequate to break the bond and remove. Clean any residue with a solvent which will not damage the parts.

Tack-Free ESP 7455 is an alumina-filled, epoxy film adhesive designed for bonding component and substrate to a mismatched substrate or carrier. The dry, tack-free handling of the film makes it suitable for an automated assembly. The adhesive film has very low ionic impurities of less than 10 ppm and high thermal stability with TGA degradation at 450°C. ESP7455 has good thermal conductivity. The extra low Tg of -60°C helps to minimize thermal stress on the bonded parts during thermal cycling or shock testing from -55 to 150°C.

ME8412 is a silver filled, solvent free, electrically and thermally conductive paste. It is designed for automated, online, die attach processing. It is thixotropic and will not sag on vertical surfaces. Designed to meet the hybrid adhesive specification, Mil Std 883; Method 5011.4 in terms of ionic impurities, ME8412 exhibits low outgassing at 125C and passes NASA outgassing requirements.

EG7655 is a reworkable, alumina filled, electrically insulating and thermally conductive epoxy paste adhesive which exhibits outstanding flexibility for bonding materials with highly mismatched CTE'S (i.e., alumina to aluminum, silicon to copper). EG7655's high thermal conductivity and flexibility make it excellent for bonding large area substrates, components and heat sinks where thermal management is critical. EG7655 exhibits reduced bond strength at 80-100°C for easier rework. The cured adhesive is flexible with Type A hardness of 80 and tensile elongation of more than 30%.

RTK7659 is a tack-film, reworkable, diamond-filled, epoxy film adhesive designed for bonding die, component and substrate to a mismatched substrate or carrier. This B-Staged, dielectric adhesive offers excellent reworkability at 80-150°C. RTK7659 has excellent thermal conductivity and the low Tg of the adhesiveimposes minimum thermal stress on bonded parts during thermal cycling or shock testing.

ME7857-SC is a medium viscosity, silicon carbide filled, flexible epoxy for snap curing application. It is a reworkable, electrically insulating and thermally conductive epoxy paste adhesive. It exhibits outstanding flexibility down to -60°C. Ideal for bonding materials having highly mismatched CTE's (i.e., alumina to aluminum, silicon to copper). The stress-free flexible adhesive maintains good stable bond strength of 100 psi from 150-250°C and has outstanding thermal stability.

ME7863 is a one part, quartz filled cyanate ester die attach adhesive. It was designed for solder-sealed ceramic packages. It can withstand temperatures up to 300°C without thermal degradation. ME7863 has processing characteristics required in high speed automation. Its unique chemistry results in very low moisture absorption, high adhesive strength and low CTE.